

Rvm interface pcb
KiCad schematic and PCB layout for an interface board that connects an Arduino Mega to the sensors, actuators and communication modules of a Reverse Vending Machine (RVM).
- Size
- 90 × 70 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 25
- Nets
- 28
- Pads
- 88
- Tracks, vias
- 228, 0
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 25 Oct 2026
- Updated
- 26 Oct 2026
Overview
Rvm interface pcb is an open-source printed circuit board by zk946190-ui, from the zk946190-ui/rvm-interface-pcb repository on GitHub. It is a 2-layer board of 90 × 70 mm with 25 parts on 28 nets, routed with 228 tracks and 0 vias.
It is built around the HX711 and BC547. Its parts include 11 connectors, 4 resistors, 3 diodes, 2 capacitors and 1 transistor. It belongs with the interfaces and adapters boards of this library.
Main components
2README
README.mdReverse Vending Machine Interface PCB (Rev 1)
KiCad schematic and PCB layout for an interface board that connects an Arduino Mega to the sensors, actuators and communication modules of a Reverse Vending Machine (RVM). The board replaces breadboard and loose-wire connections with one organised PCB.
Status: Rev 1 design, not fabricated and not tested on hardware yet. See Progress.
Schematic

PCB layout

The board is routed on the top and bottom copper layers, with four M3 mounting holes (3.2 mm).
Project objectives
- Capture the circuit as a KiCad schematic.
- Lay out and route a PCB that connects all RVM modules to the Arduino Mega through one header.
- Keep signal, power and ground connections organised and labelled.
- Use connectors for every module so the board can be wired and replaced easily.
- Prepare the design for design-rule checks and fabrication.
Modules and connectors
| Module | Connector on board | Power rail |
|---|---|---|
| Arduino Mega | Dual-row header (MEGA_LINK) | n/a |
| LCD (I2C) | LCD header (SDA, SCL) | 5V_MEGA |
| HX711 load cell amplifier | HX711 header (HX_DT, HX_SCK) | 5V_MEGA |
| Metal sensor | METAL_SENSOR header | 5V_MEGA |
| Bluetooth (HC-05) | BLUETOOTH header | 5V_MEGA |
| 4x4 keypad | KEYPAD header (4 rows, 4 columns) | n/a |
| Servo motor (select) | SERVO_SELECT header | 5V_EXT |
| Servo motor (drop) | SERVO_DROP header | 5V_EXT |
| GSM module | GSM header (GSM_TX, GSM_RX) | 5V_EXT |
| Buzzer | BUZZER header (driven by a transistor) | 5V_EXT |
| External power input | POWER_IN screw terminal | 5V_EXT |
Circuit design notes
- Two supply rails: the logic modules (LCD, HX711, Bluetooth, metal sensor) use
5V_MEGA. The higher-current loads (servos, GSM, buzzer) use a separate external5V_EXTsupply. All grounds are on one commonGNDnet. - Bluetooth RX level divider: a 1 kΩ and a 2.2 kΩ resistor form a voltage divider on the HC-05 RX line, which is fed from the Arduino TX1 pin.
- Buzzer driver: a BC547 NPN transistor with a 1 kΩ base resistor switches the buzzer from the
BUZ_CTRLsignal. A 1N4148 diode is placed across the buzzer. - Power input: a 1N5819 Schottky diode sits in the external 5 V input path.
- Decoupling: a 0.1 µF capacitor and a 1000 µF capacitor sit on the
5V_EXTrail. - Indicator: an LED with a 330 Ω resistor on
5V_EXT.
Signal names
Fill in the Arduino pin used for each signal.
| Signal | Function | Arduino Mega pin |
|---|---|---|
| SDA, SCL | LCD (I2C) | ___ , ___ |
| HX_DT, HX_SCK | HX711 load cell amplifier | ___ , ___ |
| METAL | Metal sensor output | ___ |
| SERVO_SEL, SERVO_DROP | Servo control signals | ___ , ___ |
| MEGA_TX1 / BT_TXD | Bluetooth link | ___ |
| GSM_TX, GSM_RX | GSM module serial | ___ , ___ |
| BUZ_CTRL | Buzzer control | ___ |
| KEY_R1 to KEY_R4 | Keypad rows | ___ |
| KEY_C1 to KEY_C4 | Keypad columns | ___ |
Project files
| File | Description |
|---|---|
rvm interface pcb.kicad_pro | KiCad project |
rvm interface pcb.kicad_sch | Schematic |
rvm interface pcb.kicad_pcb | PCB layout |
Open the .kicad_pro file with KiCad (the project was created with KiCad 10).
Progress
- Schematic capture
- Component placement and track routing (Rev 1)
- Electrical Rules Check (ERC) passed
- Design Rules Check (DRC) passed
- 3D view and Bill of Materials (BOM)
- Gerber and drill files
- Fabrication and hardware testing
What I learned
- Drawing a schematic and assigning component footprints in KiCad
- Placing components and routing tracks on a two-layer board
- Designing separate power rails and a level divider for 3.3 V and 5 V modules
- Preparing a design for design-rule checks and manufacturing
Disclaimer
This is an educational PCB design project based on a Reverse Vending Machine concept. The board has not been fabricated or validated on physical hardware. Check the connections, footprints, power requirements and design rules against each module's datasheet before building it.
Related project
RVM Verification Framework: a Python test framework and REST API for a simulated version of the same machine.
Parts
25| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 1K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R3 |
| 1 | 0.1uF | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C1 |
| 1 | 1000uF | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C2 |
| 1 | 1N4148 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D2 |
| 1 | 1N5819 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D1 |
| 1 | 2.2K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
| 1 | 330 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | BC547 | Package_TO_SOT_THT:TO-92_Inline | Q1 |
| 1 | BLUETOOTH | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J8 |
| 1 | BUZZER | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J11 |
| 1 | GSM | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J9 |
| 1 | HX711 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | KEYPAD | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J4 |
| 1 | LCD | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | LED | LED_THT:LED_D3.0mm | D3 |
| 1 | MEGA_LINK | Connector_PinHeader_2.54mm:PinHeader_2x13_P2.54mm_Vertical | J1 |
| 1 | METAL_SENSOR | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | POWER_IN | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J10 |
| 1 | SERVO_DROP | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | SERVO_SELECT | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J6 |
The 21 most common of 25 parts.
Similar boards
- 2 layers68.1 × 38.1 mm

- 2 layers15.3 × 19.3 mm

Kicad hx711 tyny85
IvDm/Z-probe-on-smd-resistors-2512
Auto bed level strain gage for 3D printer using resistors 2512 instead of strain gauges.
18 parts150GPL-3.0 - 2 layers109.2 × 74.9 mm

- 4 layers81.2 × 81.2 mm

- 2 layers128 × 77 mm

- 2 layers60 × 40 mm

Forcegauge
szbeni/forcegauge
Traning for climbing. Load cell with HX711 and real time plotting,
77 parts18GPL-3.0 - 2 layers112 × 57 mm

Caravansensor
MartinVerges/womolin-waterlevel
DIY project to build a smart fuel sensor for RVs or in other projects. It is based on air pressure and is able to measure fresh water as well as grey and black water levels with high precision.
226 parts17 - 2 layers71.1 × 109.2 mm

Questions
How big is the Rvm interface pcb PCB?
It measures 90 × 70 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Rvm interface pcb use?
25 parts, built around the HX711 and BC547. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Rvm interface pcb KiCad files?
From the zk946190-ui/rvm-interface-pcb repository on GitHub, at the commit this page was made from: the board is rvm interface pcb.kicad_pcb and its schematic rvm interface pcb.Kicad_sch.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Rvm interface pcb design in my own project?
Its repository states no licence, so its author keeps all rights: ask zk946190-ui before reusing the design.