
Core micro surface nohotswap
zeerolux/core-micro
A lighting controller, control surface with 5 faders and 2 encoders, a USB DMX interface, an ARTNET node, and a standalone DMX generator.

A lighting controller, control surface with 5 faders and 2 encoders, a USB DMX interface, an ARTNET node, and a standalone DMX generator.
Core micro pcb is an open-source printed circuit board by zeerolux, from the zeerolux/core-micro repository on GitHub. It is a 2-layer board of 81.5 × 65.5 mm with 70 parts on 92 nets, routed with 780 tracks and 99 vias.
It is built around the RP2040, W25Q128JVSIQ and USBLC6-2SC6, with the W5500 and HR911105A among its other parts. Its parts include 24 capacitors, 14 resistors, 9 connectors, 5 ICs and 1 diode. It belongs with the RP2040 boards of this library.
A lighting controller, control surface with 5 faders and 2 encoders, a USB DMX interface, an ARTNET node, and a standalone DMX generator. The Core-Micro system consists or 4 modules; the logic processor, the control surface, the DMX interface, and the redundant USB-C power supply. These modules are designed in a way that allows them to be iterated on separetly and allow for a limitless amount of configuration. How do you use Core-Micro? It depends on how YOU need to use it. Core-Micro can be used as a midi controller for On-PC lighting softwares, it can be used in a standalone mode where it acts like an all in one system for controlling stage lighting, and eventually it will be able to run in conjuction with other Zeerolux hardware and software as either the main controller or as a programming wing. It can also be used as an ARTNET node, this means that you can connect to it over the network and output DMX out its outputs.
I decided to take on this project after I realised how incredibly expensive lighting consoles are. Out of curiosity, I wanted to see whether I could build my own console and what price it would turn out at. Another inspiration was my experience with the Avolites Quartz which to say the least was... frustrating, so naturally, I was fresh with ideas on what not to do.
Core-Micro has four PCBs; one for each module.
The Logic PCB does a few main things:
This PCB's purpose is as follows:
Why do we need a separate PCB for power? Redundancy. In a live production environment, we cannot tolerate any power cuts or flaky USB connections. Therefore, I designed a board that has two inputs that can automatically be switched between if one cuts out. This allows for:
This simple PCB converts the PIO DMX signal into RS485 signal that can be sent to DMX fixtures. This board also has both 3-pin and 5-pin XLR to ensure you can connect to any light.
At this current moment, the software is a minimal version designed for testing DMX and ARTNET in a standalone mode. Here is the ideal list of software features I would like to implement:
| Item | Qty | Link / Supplier | List Price | Actual | Location | Shipping |
|---|---|---|---|---|---|---|
| Surface PCB | 5 | JLCPCB | 17.90 | 190.94 | JLCPCB | 33.14 |
| Surface PCB Assembly | 2 | JLCPCB | 39.89 | — | aliexpress | — |
| Logic PCB | 5 | JLCPCB | 4.00 | — | mouser | 20.00 |
| Logic PCB Assembly | 2 | JLCPCB | 48.14 | — | beekeeb | 15.64 |
| DMX PCB | 5 | JLCPCB | 4.00 | — | — | — |
| DMX PCB Assembly | 2 | JLCPCB | 18.58 | — | — | — |
| Power PCB | 5 | JLCPCB | 2.00 | — | — | — |
| Power PCB Assembly | 2 | JLCPCB | 43.29 | — | — | — |
| Encoders | 3 | Mouser | 5.07 | 5.07 | — | — |
| Faders | 5 | Mouser | 9.60 | 9.60 | — | — |
| USB B Socket | 1 | Mouser | 0.95 | 0.95 | — | — |
| Threaded Inserts M3 | 100 | AliExpress | 5.00 | 5.00 | — | — |
| Threaded Inserts M2 | 100 | AliExpress | 5.00 | 5.00 | — | — |
| Screws M3 | 50 | AliExpress | 3.00 | 3.00 | — | — |
| Screws M2 | 50 | AliExpress | 3.00 | 3.00 | — | — |
| Key Switches | 50 | Beekeeb | 49.00 | 49.00 | — | — |
| Neutrik 3 Pin XLR | 2 | Mouser | 5.64 | 5.64 | — | — |
| Neutrik 5 Pin XLR | 2 | Mouser | 7.74 | 7.74 | — | — |
| Shipping (overall products) | — | — | 68.78 | — | — | — |
| Total Cost | — | — | 284.94 | — | — | — |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100nF | Capacitor_SMD:C_0402_1005Metric | C3, C4, C11, C12, C15, C16, C17, C18, C19, C21, C22, C23, C24 |
| 7 | 1uF | Capacitor_SMD:C_0402_1005Metric | C1, C2, C5, C6, C7, C8, C14 |
| 6 | Screw_Terminal_01x02 | TerminalBlock:TerminalBlock_Xinya_XY308-2.54-2P_1x02_P2.54mm_Horizontal | J1, J2, J3, J4, J5, J6 |
| 5 | 1k | Resistor_SMD:R_0402_1005Metric | R8, R11, R13, R14, R15 |
| 3 | 10k | Resistor_SMD:R_0402_1005Metric | R9, R10, R12 |
| 2 | 22pF | Capacitor_SMD:C_0402_1005Metric | C9, C10 |
| 2 | 27R | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | 5k1 | Resistor_SMD:R_0402_1005Metric | R6, R7 |
| 2 | FerriteBead | Inductor_SMD:L_0603_1608Metric | FB1, FB2 |
| 2 | R | Resistor_SMD:R_0402_1005Metric | R1, R5 |
| 1 | 10uF | Capacitor_SMD:C_0402_1005Metric | C13 |
| 1 | 12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1nF | Capacitor_SMD:C_0402_1005Metric | C20 |
| 1 | HR911105A | HR911105A:HANRUN_HR911105A | J9 |
| 1 | LED | LED_SMD:LED_0201_0603Metric | D1 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm_ThermalVias | U1 |
| 1 | SWD | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J8 |
| 1 | SW_Push | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | SW1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U5 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J7 |
| 1 | W25Q128JVS | W25Q128JVSIM:SOIC127P790X216-8N | U2 |
| 1 | W5500 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U4 |
| 1 | XC6206PxxxMR-Regulator_Linear | Package_TO_SOT_SMD:SOT-23 | U3 |
The 57 most common of 70 parts.

zeerolux/core-micro
A lighting controller, control surface with 5 faders and 2 encoders, a USB DMX interface, an ARTNET node, and a standalone DMX generator.

zeerolux/core-micro
A lighting controller, control surface with 5 faders and 2 encoders, a USB DMX interface, an ARTNET node, and a standalone DMX generator.

zeerolux/core-micro
A lighting controller, control surface with 5 faders and 2 encoders, a USB DMX interface, an ARTNET node, and a standalone DMX generator.

OpenJBOD/rp2040
This repository contains the hardware design files OpenJBOD RP2040 Baseboard.



enkhbold470/iron-node
ESP32-S3 industrial gateway: W5500 Ethernet, isolated RS-485 (ADM2587E), CAN, 9-36 V input. 4-layer KiCad 10 board.

Takingo/Mypcb35
OmniCircuit AI is a local proof of concept for an autonomous PCB/PCBA design and manufacturing suite. The current implementation focuses on the ESP32-S3 + DWM3000 UWB Anchor example and establishes the architecture for:

adeboni/laser-projector
This project is for a quadruple laser projection controller, aimed at supporting room-scale projections

adeboni/eurorack
This repository stores various eurorack module designs I've made

It measures 81.5 × 65.5 mm and has 2 copper layers, 1.6 mm thick.
70 parts, built around the RP2040, W25Q128JVSIQ, USBLC6-2SC6 and W5500. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the zeerolux/core-micro repository on GitHub, at the commit this page was made from: the board is pcb/core-micro-logic/core-micro-pcb.kicad_pcb and its schematic pcb/core-dmx/core-dmx.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask zeerolux before reusing the design.