
TDR 5351 core
MR-DOS/TDR_diploma_thesis
Time domain reflectometer. Includes Hardware, firmware and GUI in Octave. Also a diploma thesis.

CBM 1551 paddle replacement / mass storage using an SD card interfacing with the Commodore C16/116/Plus4 simulating a TCBM bus 1551 disk drive
Tcbm2sd is an open-source printed circuit board by ytmytm, from the ytmytm/plus4-tcbm2sd repository on GitHub. It is a 2-layer board of 56 × 91 mm with 27 parts on 83 nets, routed with 1,318 tracks and 164 vias.
It is built around the AMS1117-3.3 and AMS1117. Its parts include 7 capacitors, 5 connectors, 4 ICs, 3 resistors and 2 switches. It belongs with the retro computing and games and fPGA and programmable logic boards and the FPGA and CPLD boards of this library.
CBM 1551 paddle replacement and/or mass storage using an SD card interfacing with the Commodore C16/116/Plus4 simulating a TCBM bus 1551 disk drive.
This board can also serve as the Commodore-side TCBM interface for the Pi1551, a cycle-exact Commodore 1551 emulator for Raspberry Pi. It can be used with either the Pi1551-HAT or Pi1551-III interface.
It is also the TCBM interface for the 1551-rePico, a 1551 drive replacement that uses a real 6510T with Raspberry Pico 2 emulating the analog parts.
The Parobek function ROM is a useful way to populate the 32/64 KiB ROM socket. It includes the TCBM2SD boot software, so boot.t2sd is not needed when using that ROM.
Click for video
The photos and PCB view below show an older board revision and are provided for reference only.
Click for video
Click for video
TCBM2SD does not emulate a 1551, but simulates its behavior:
* file, which loads and runs BOOT.T2SD from the root directory; this can be any file that runs from BASIC. Directory Browser patched with fastload protocol is recommended. When using the Parobek function ROM, BOOT.T2SD is already included in the ROM and is not needed on the SD card.CD, R, S, MD, RD, I, UI, UJIt has been confirmed that tcbm2sd works as a 1551 paddle cartridge replacement with a real 1551 drive. The Arduino can be removed or disabled for this purpose.
The paddle part exposes all TCBM bus signals and can be used as a basis for other TCBM hardware projects.
For development, another daughterboard or a ready-to-use microcontroller module can be used. All TCBM bus signals are exposed at the cartridge edge (TCBM connector) or Arduino footprint. Signals are already at 3.3 V logic, so no additional level shifter is necessary for a Raspberry Pi.
Please note that if a TCBM cable is connected then both pins 1 and 16 of the TCBM connection must be connected to GND. It's used by Arduino to detect if TCBM cable is attached so that Arduino can disable itself.
The information published here includes everything required to manufacture the PCB (Gerber files) and program the firmware.
If you want a completed unit, please drop me a message (you will find my email address at the top of loader/loader.asm). I might have some units to sell; please include your country.
You might also be interested in a cartridge case. It should fit inside this one, although it requires cutting a slot for the SD card.
This example shows revision 1.1 without NEXT/PREV buttons
There is also an updated case project that should fit revision 1.3 and 1.4 PCBs without any extra holes.
This project builds on work and documentation provided by others:
diskimage.c D64/71/81 handling code| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4 |
| 3 | 10µ | Capacitor_Tantalum_SMD:CP_EIA-3216-12_Kemet-S_HandSolder | C5, C6, C7 |
| 2 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3 |
| 2 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm_NumberLabels | JP3, JP4 |
| 1 | 2.2R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 27C512 | Package_DIP:DIP-28_W15.24mm_Socket | U4 |
| 1 | ALT_A6_A7 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | AMS1117 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | Arduino Pro Mini | Arduino:Arduino_Pro_Mini | U2 |
| 1 | BUT_NEXT | LittleSixteen:SW_PUSH_6mm_OR_SW_Tactile_SPST_Angled_PTS645Vx58-2LFS | SW2 |
| 1 | BUT_PREV | LittleSixteen:SW_PUSH_6mm_OR_SW_Tactile_SPST_Angled_PTS645Vx58-2LFS | SW1 |
| 1 | C16_CARTRIDGE | c264-magic-cart-rev1:C16_CART | U$1 |
| 1 | JTAG | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | SD CARD | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J5 |
| 1 | SD connector | SD2IECplug:Conn_uSDcard | XS1 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1 |
| 1 | SolderJumper_3_Open | Jumper:SolderJumper-3_P1.3mm_Open_Pad1.0x1.5mm_NumberLabels | JP2 |
| 1 | TCBM | Connector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_Vertical | J1 |
| 1 | XC9572XL-VQ64 | Package_QFP:TQFP-64_10x10mm_P0.5mm | U1 |

MR-DOS/TDR_diploma_thesis
Time domain reflectometer. Includes Hardware, firmware and GUI in Octave. Also a diploma thesis.

Robotics-Competence-Center-Illertal-e-V/RocciBoard-PCB
Layout and Schematic for the Rocci Board


ytmytm/plus4-burstcart
Burst (fast serial) capable cartridge for Commodore C16/116/Plus4

yogendra-kumawat/pcb-hub
This folder contains the complete KiCad project for the writing machine motor driver board.

AlessandroAU/Chorus32-ESP32LapTimer
This is an ESP32 port of the popular Chorus RF Laptimer


It measures 56 × 91 mm and has 2 copper layers, 1.6 mm thick.
27 parts, built around the AMS1117-3.3 and AMS1117. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ytmytm/plus4-tcbm2sd repository on GitHub, at the commit this page was made from: the board is tcbm2sd/tcbm2sd.kicad_pcb and its schematic tcbm2sd/tcbm2sd.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask ytmytm before reusing the design.