2 layers50 × 57 mm
2 layers72 × 47 mm
LED driver
xtompok/LED_driver3x5A PWM driver for LED strips
- Size
- 72 × 47 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 96
- Nets
- 80
- Pads
- 333
- Tracks, vias
- 1,065, 106
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 3 Jan 2020
- Updated
- 6 Nov 2024
Overview
LED driver is an open-source printed circuit board by xtompok, from the xtompok/LED_driver repository on GitHub, published under the MIT licence. It is a 2-layer board of 72 × 47 mm with 96 parts on 80 nets, routed with 1,065 tracks and 106 vias.
It is built around the SN65HVD3082EDR, ZXGD3009E6TA and BY25Q16BSTIG(R), with the MIC5504-3.3YM5, YJD80G06A and BZT52C15 among its other parts. Its parts include 36 resistors, 21 capacitors, 11 ICs, 11 connectors and 8 diodes. It belongs with the STM32 boards of this library.
Main components
8
SN65HVD3082EDR
SOP-8-40℃~+85℃ 1 1 12Mbps 3.3V 32 425uA Enable shutdown、Overcurrent Protection、Thermal shutdown protection、Tx/Rx enable Half-Duplex Transceiver ±8kV SOP-8 RS-485 / RS-422 ICs ROHSJSMSEMIRS-485 / RS-422 ICs
ZXGD3009E6TA
SOT-26-55℃~+150℃ 1 20nA 210ns 240ns 2A 2A 40V Interleaved conduction protection Low Side MOSFET SOT-26 Gate Drivers ROHSDiodes IncorporatedGate DriversBY25Q16BSTIG(R)
SOP-8-40℃~+85℃ 100,000 cycles 108MHz 16Mbit 2.7V~3.6V 20 Years 5uA 600us Power-on reset、Hardware Write Protection、Software Write Protection、Write enable latch、Absolute Write Protection SPI SOP-8 NOR FLASH ROHSBOYAMICRONOR FLASH
MIC5504-3.3YM5
SOT-23-5-40℃~+125℃@(Tj) 1 120uVrms 15uA 180mV@(300mA) 3.3V 300mA 5.5V 75dB@(1kHz) Fixed Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
YJD80G06A
TO-252-55℃~+150℃ 1 N-channel 1.525nF 11mΩ@4.5V 13.5pF 2.5V 31nC@10V 372pF 60V 78W 80A N-Channel TO-252 MOSFETs ROHSYangzhou Yangjie Electronic TechnologyMOSFETs
BZT52C15
SOD-123-65℃~+150℃ 1 Independent 100nA@1V 13.8V~15.6V 15V 200Ω 30Ω 370mW SOD-123 Zener Diodes ROHSDiodes IncorporatedZener Diodes
SE60P20B
TO-252-55℃~+150℃ 1 P-Channel 1.25nF 170W 180nC@10V 2.5V 20A 3.5nF 33mΩ@10V 450pF 60V P-Channel TO-252 MOSFETs ROHSSINO-ICMOSFETs
STPS160A
SMA(DO-214AC)1 Independent 1A 4uA@60V 60V 670mV@1A 75A SMA(DO-214AC) Schottky Diodes ROHSSTMicroelectronicsSchottky Diodes
Parts
96| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C2, C10, C11, C16, C20, C21, C30, C31, C51, C61, C71, C81 |
| 5 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R2, R6, R7, R12 |
| 5 | 1k | Resistor_SMD:R_0603_1608Metric | R33, R52, R62, R72, R82 |
| 5 | 4k7 | Resistor_SMD:R_0603_1608Metric | R28, R51, R61, R71, R81 |
| 4 | 1u | Capacitor_SMD:C_0603_1608Metric | C5, C6, C8, C13 |
| 4 | 330R | Resistor_SMD:R_0603_1608Metric | R24, R25, R26, R27 |
| 3 | 0.01R | Resistor_SMD:R_1206_3216Metric | R11, R21, R31 |
| 3 | 100R | Resistor_SMD:R_0603_1608Metric | R10, R20, R30 |
| 3 | INA180A2 | Package_TO_SOT_SMD:SOT-23-5 | U11, U21, U31 |
| 3 | YJD80G06A | Package_TO_SOT_SMD:TO-252-2 | Q10, Q20, Q30 |
| 3 | ZXGD3009E6 | Package_TO_SOT_SMD:SOT-23-6 | U10, U20, U30 |
| 2 | 1k5 | Resistor_SMD:R_0603_1608Metric | R8, R9 |
| 2 | 27p | Capacitor_SMD:C_0603_1608Metric | C4, C7 |
| 2 | 33k | Resistor_SMD:R_0603_1608Metric | R4, R23 |
| 2 | 720R | Resistor_SMD:R_0603_1608Metric | R34, R36 |
| 2 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric | C9 |
| 1 | 120R | Resistor_SMD:R_0603_1608Metric | R35 |
| 1 | 150k | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 1k2 | Resistor_SMD:R_0603_1608Metric | R29 |
| 1 | 2u2 | Capacitor_SMD:C_0603_1608Metric | C12 |
| 1 | 560R | Resistor_SMD:R_0603_1608Metric | R32 |
| 1 | 8MHz | Crystal:Crystal_HC49-U_Vertical | Y1 |
| 1 | ADC_EXT | Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J10 |
| 1 | AP2204K-5.0 | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | BUTTONS | Connector_Molex:Molex_Micro-Fit_3.0_43045-0800_2x04_P3.00mm_Horizontal | J9 |
| 1 | BY25Q16BSTIG | Package_SO:SOP-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | BZT52C15 | Diode_SMD:D_SOD-123F | D1 |
| 1 | I2C | Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J8 |
| 1 | LED_EN | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J11 |
| 1 | LED_STRIPS | Connector_Molex:Molex_Micro-Fit_3.0_43045-0600_2x03_P3.00mm_Horizontal | J2 |
| 1 | L_12V | LED_SMD:LED_PLCC-2 | D8 |
| 1 | L_RX | LED_SMD:LED_PLCC-2 | D6 |
| 1 | L_TX | LED_SMD:LED_PLCC-2 | D5 |
| 1 | L_U1 | LED_SMD:LED_PLCC-2 | D3 |
| 1 | L_U2 | LED_SMD:LED_PLCC-2 | D4 |
| 1 | L_VCC | LED_SMD:LED_PLCC-2 | D7 |
| 1 | MIC5504-3.3YM5 | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | NTCC-22k | Capacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | TH1 |
| 1 | POWER | Connector_Phoenix_MSTB:PhoenixContact_MSTB_2,5_3-GF-5,08_1x03_P5.08mm_Horizontal_ThreadedFlange | J3 |
| 1 | PROG | Connector_Molex:Molex_KK-254_AE-6410-05A_1x05_P2.54mm_Vertical | J1 |
| 1 | RS485_1 | LED_driver:PTSA_1.5_3-3.5-Z_1985205 | J6 |
| 1 | RS485_2 | LED_driver:PTSA_1.5_3-3.5-Z_1985205 | J7 |
| 1 | RST | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | SE60P20B | Package_TO_SOT_SMD:TO-252-2 | Q1 |
| 1 | SINGLE_POWER | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | SN65HVD3082EDR | Package_SO:SOP-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | STM32F030C8Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U3 |
| 1 | STPS160A | Diode_SMD:D_SMA | D2 |
| 1 | TestPoint | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP1 |
Questions
How big is the LED driver PCB?
It measures 72 × 47 mm and has 2 copper layers, 1.6 mm thick.
What parts does the LED driver use?
96 parts, built around the SN65HVD3082EDR, ZXGD3009E6TA, BY25Q16BSTIG(R) and MIC5504-3.3YM5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the LED driver KiCad files?
From the xtompok/LED_driver repository on GitHub, at the commit this page was made from: the board is hw/LED_driver.kicad_pcb and its schematic hw/LED_driver3/LED_driver3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the LED driver design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
More from xtompok/LED_driver
2- 2 layers60 × 65 mm
Similar boards
- 4 layers255.9 × 224.5 mm
Central control unit
RomLab/pcb-system-for-underfloor-heating-v2.0
PCB for underfloor heating system
1,880 parts1 - 2 layers80 × 100 mm
- 4 layers107.5 × 102.5 mm
- 2 layers50 × 44 mm
Baseboard
xtompok/home_automation_switchboard
Board fitting into wall switch, support for 1Wire, quadrature encoder, and much more. RS-485
82 partsMIT - 2 layers35 × 35 mm
- 2 layers58.4 × 66.7 mm
PWM10
Duckle29/PWM-Solar-Charge-Controller
A PWM Solar Charge controller based on Julian Lietts PWM5
55 parts9MIT - 2 layers77 × 73.5 mm
EChook Nano
eChook/eChook-Nano-PCB
Designspark Schematics and PCB files, and PCB Gerber Files
141 parts2 - 4 layers220 × 130 mm
Gantry controller prototype DUE
kitspace-forks/growbox-open-motion-mobo
A general purpose open source Arduino DUE based motion controller designed to run the Synthetos G2 motion control fimware
138 parts