2 layers121.9 × 99.8 mm
2 layers190 × 152 mm
TiNA append
wyolum/TiNAStandalone controller for TIM (The Intelligent Matrix)
- Size
- 190 × 152 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 137
- Nets
- 161
- Pads
- 663
- Tracks, vias
- 1,566, 81
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 3
- Created
- 30 Jan 2014
- Updated
- 26 Sep 2014
Overview
TiNA append is an open-source printed circuit board by wyolum, from the wyolum/TiNA repository on GitHub. It is a 2-layer board of 190 × 152 mm with 137 parts on 161 nets, routed with 1,566 tracks and 81 vias.
It is built around the TPS62133RGT, ADXL345-EP and CAT24C256LI, with the DS3231N/DIP, TXB0104D and BCP5416TA among its other parts. Its parts include 39 capacitors, 26 connectors, 21 resistors, 9 ICs and 8 diodes. It belongs with the lEDs and displays boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
6
TPS62133RGT
VQFN-16-EP(3x3)-40℃~+125℃ 1 1.25MHz~2.5MHz 17uA 3A 3V~17V 5V Buck Buck Built-in Fixed Yes VQFN-16-EP(3x3) DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
ADXL345-EP
LGA-14(3x5x0.8)LGA-14(3x5x0.8) New Arrivals ROHSAnalog DevicesUncategorised
CAT24C256LI
PDIP-81,000,000 cycles 1.8V~5.5V 100 Years 256Kbit 400kHz 5ms Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C PDIP-8 EEPROM ROHSonsemiEEPROM
DS3231N/DIP
--40℃~+85℃ 2.3V~5.5V Built-in I2C Temperature compensation、Backup power management and battery charging、Programmable clock output、Alarm function - Real Time Clocks ROHSMaxim Integrated (Analog Devices)Real Time Clocks
TXB0104D
SOIC-14-40℃~+85℃ 1 1.2V~3.6V 1.65V~5.5V 100Mbps 4 Auto Direction Detection Bidirectional CMOS CMOS Tri-State SOIC-14 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level Shifters
BCP5416TA
SOT-223-65℃~+150℃ 1 NPN 10 150MHz 1A 20uA 2W 500mV 5V 80V NPN SOT-223 Bipolar (BJT) ROHSDiodes IncorporatedBipolar (BJT)
README
README.mdTiNA
Standalone controller for TIM (The Intelligent Matrix)
To install arduino libraries:
- download and unzip (or git clone) the files to a local directory for example, my this is /home/justin/code/TiNA
- set your arduino sketchbook path to the arduino subdirectory of your install path by either a. editing your ~/.arduino/preferences.txt (the sketchbook.path variable) b. selecting from the "File->Preferences" drop down menu item for example, my sketchbook path is /home/justin/code/TiNA/arduino
- start or restart the Arduino IDE
Parts
137| Qty | Value | Footprint | References |
|---|---|---|---|
| 21 | 100n | c_0805 | C1, C4, C10, C11, C12, C13, C14, C17, C23, C28, C29, C31, C39, C40, C41, C43 +5 |
| 10 | SCREW | vite_3mm | SC1, SC2, SC3, SC4, SC5, SC6, SC7, SC8, SC9, SC10 |
| 8 | 10k | r_0805 | R1, R2, R3, R4, R11, R15, R21, R22 |
| 4 | 100nF | c_0805 | C18, C20, C32, C34 |
| 4 | 100uF | C_ELCO_SMD | C22, C26, C36, C37 |
| 4 | 1N4007 | diode-DO214AC | D1, D3, D4, D9 |
| 4 | BCP5416TA | SOT223 | Q1, Q2, Q3, Q4 |
| 3 | 1k | r_0805 | R6, R10, R13 |
| 3 | 4k75 | r_0805 | R16, R17, R18 |
| 3 | I_O | I_O | B1, B2, B3 |
| 2 | 100k | r_0805 | R7, R14 |
| 2 | 100u,16V | C_ELCO_SMD | C27, C42 |
| 2 | 10uF X7R | c_1206 | C30, C38 |
| 2 | 1k5 | r_0805 | R19, R20 |
| 2 | 22p | c_0603 | C2, C3 |
| 2 | 22uF X7R | c_1210 | C19, C33 |
| 2 | 2u2H,3.0A | Inductor_SMD3 | L1, L2 |
| 2 | 3.3nF | c_0805 | C21, C35 |
| 2 | 5V_EXT | Header_2 | J1, J2 |
| 2 | C3SB | pin_strip_4-90 | P9, P10 |
| 2 | CONN_23X2 | PIN_ARRAY_23X2 | P21, P22 |
| 2 | Logo_OH | OSHW_6mm | G3, G4 |
| 2 | PB0 | I_O | B4, B12 |
| 2 | TPS62133 | TPS62132 | U3, U4 |
| 1 | 120E | r_0805 | R9 |
| 1 | 12V | led_0805 | D8 |
| 1 | 16MHz | Xtal_SMD3 | X1 |
| 1 | 330E | r_0805 | R8 |
| 1 | 3V3 | led_0805 | D6 |
| 1 | 4k7 | r_0805 | R5 |
| 1 | 5V0 | led_0805 | D5 |
| 1 | 5V_LINK | ShortLink2 | P20 |
| 1 | ABSO_PR | HDIB002AUY8H5 | P8 |
| 1 | ADXL345 | ADXL345 | U11 |
| 1 | AREF | ShortLink2 | P1 |
| 1 | ATMEGA328-AU-ND | TQFP32 | U7 |
| 1 | Alt_Add | ShortLink2 | P23 |
| 1 | BATT_HOLDER | CR2032 | BT1 |
| 1 | BEAGLEBONE | BEAGLEBONE | U10 |
| 1 | BLINK | led_0805 | D7 |
| 1 | BUZZER | Speaker | SP1 |
| 1 | CAT24C256 | SO8E | U9 |
| 1 | DS3231N | DS3231 | U5 |
| 1 | FLOWMETER | FlowMeter_CFM3000 | P16 |
| 1 | FTDI | Header_FTDI | P5 |
| 1 | Flow_Conn | Conn_Flow_SFM3000_Male | P15 |
| 1 | GAGE_PR | HCEM500GUH9P3 | P7 |
| 1 | ICSP | Header_ISP | P4 |
| 1 | INT0 | SW_PB_V_H | SW2 |
| 1 | INT1 | SW_PB_V_H | SW3 |
| 1 | Int1 | ShortLink2 | P28 |
| 1 | Int2 | ShortLink2 | P29 |
| 1 | PC0 | I_O | B8 |
| 1 | PC1 | I_O | B9 |
| 1 | PC6 | I_O | B10 |
| 1 | PC7 | I_O | B11 |
| 1 | PCB | PCB | PCB1 |
| 1 | PUMP | Pump_P54E01R_02 | P17 |
| 1 | PWR_IN | JACK_ALIM | P24 |
| 1 | PWR_IN | Header_2 | P13 |
| 1 | Reset | SW_PB_V_H | SW1 |
| 1 | TSX0108 | TXS0108EPWR | U8 |
| 1 | TXB0104D | TXB0104D | U1 |
| 1 | U6_OE | ShortLink2 | P19 |
| 1 | VSel_Vlv | Header_3 | P11 |
| 1 | VSel_Vlv2 | Header_3 | P34 |
| 1 | X_VALVE | X_Valve_2 | P14 |
| 1 | X_VALVE2 | X_Valve_2 | P38 |
| 1 | addr | Header_2x2 | J3 |
More from wyolum/TiNA
3- 2 layers38.1 × 63.5 mm
- 2 layers
Similar boards
- 2 layers190 × 152 mm
- 2 layers190 × 152 mm
UControl v2
wyolum/Wyolum-old-archive
Automatically exported from code.google.com/p/clockthree
114 parts1 - 2 layers99 × 80 mm
MmM
wyolum/mmM
mmMercury is an Open Hardware, blood pressure measurement device (not FDA approved).
167 parts2 - 2 layers
- 2 layers
- 4 layers100 × 100 mm
LED Panel Controller
drewsum/LED_Panel_Controller
Controls a single 64x64 HUB75E LED Panel
590 parts2GPL-3.0 - 4 layers105.4 × 88.9 mm
- 2 layers161.5 × 90.2 mm
Master
cactorium/UCFBrainStuff
EEG software, alpha stages. Will be opensourced when it's working!
117 partsMIT
Questions
How big is the TiNA append PCB?
It measures 190 × 152 mm and has 2 copper layers, 1.6 mm thick.
What parts does the TiNA append use?
137 parts, built around the TPS62133RGT, ADXL345-EP, CAT24C256LI and DS3231N/DIP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the TiNA append KiCad files?
From the wyolum/TiNA repository on GitHub, at the commit this page was made from: the board is KiCAD/TiNA-append.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the TiNA append design in my own project?
Its repository states no licence, so its author keeps all rights: ask wyolum before reusing the design.