Skip to the content
2 layers35.6 × 47 mmBasicesp, the printed circuit board in 3D

Simple breakout board for the ESP-12F

Size
35.6 × 47 mm
Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
17
Pads
43
Tracks, vias
53, 0
Pours
1
Routed
Yes
KiCad
KiCad 4
Created
1 Feb 2017
Updated
24 Feb 2017

Overview

Basicesp is an open-source printed circuit board by wjblack, from the wjblack/basicesp repository on GitHub, published under the WTFPL licence. It is a 2-layer board of 35.6 × 47 mm with 11 parts on 17 nets, routed with 53 tracks and 0 vias.

It is built around the LM1117-3.3. Its parts include 5 connectors, 4 resistors, 1 IC and 1 switch.

Main components

1

README

README.md

BasicESP Hardware

Introduction

This repository houses the PCB design for the BasicESP project. The ESP8266 is a super-cheap chip that has:

  • 802.11n WiFi
  • An 80 MHz Tensilica Xtensa microcontroller
  • 64+96k of I+D RAM
  • An SDIO interface
  • And a bunch of GPIO, PWM, and other SoCish goodness

It can be used either as a SDIO-attached device or as a standalone microcontroller and is available for about $2 via AliExpress on a module such as the ESP-12F, which is what this PCB design assumes. Assuming an ESP-12, this board adds:

  • 2mm pads for the ESP wifi module (the board has overhang/clearance space for the module so that the antenna gets no interference from the board). This makes it very easy to mount the ESP to the board via 2mm header pins.
  • Built-in 5V->3.3V regulator.
  • A programming switch (to easily put the ESP into programming mode on boot).
  • A serial header (to easily attach an FTDI cable).
  • All the various resistors needed for mode setting and whatnot.

Revisions

Revison 1 was the first pass and was produced in a small batch at PCBWay in January 2017. It lacked some filter capacitors that caused issues with some sensors and had various other shortcomings (see the docs inside for details).

Revision 2 is being produced now at PCBWay. It includes filter caps on the power regulator, mounting holes, a power cutoff jumper, and more pins broken out.

Thanks

Many thanks to Niklas Wennerstrand for his excellent series of intro videos for kicad on Youtube. His notes on producing the output for the manufacturer were particularly useful.

Copying

(C) 2016-17 by BJ Black

This design is released under the WTFPL license and escapes unto an unsuspecting planet with NO WARRANTY WHATSOEVER, expressed or implied. Have fun, ya filthy animals ;-)

Parts

11
QtyValueFootprintReferences
44.7kResistors_ThroughHole:Resistor_Horizontal_RM10mmR1, R2, R3, R4
2CONN_01X08Pin_Headers:Pin_Header_Straight_1x08_Pitch2.00mmP3, P4
1CONN_01X02Pin_Headers:Pin_Header_Straight_1x02P1
1CONN_01X03Pin_Headers:Pin_Header_Straight_1x03P5
1CONN_01X07Pin_Headers:Pin_Header_Straight_1x07P2
1LM1117-3.3TO_SOT_Packages_THT:TO-220_Neutral123_VerticalU1
1SW_PUSH_SMALL_HButtons_Switches_ThroughHole:SW_PUSH_SMALLSW1

More from wjblack/basicesp

1
  • 2 layers47 × 49.5 mmBasicesp, the printed circuit board in 3D

    Basicesp

    wjblack/basicesp

    Simple breakout board for the ESP-12F

    17 parts1WTFPL

Similar boards

  • 2 layers33.7 × 97.8 mmHAN ESP TSS721, the printed circuit board in 3D

    HAN ESP TSS721

    UtilitechAS/amsreader-firmware

    ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported

    29 parts470
  • 2 layers52.5 × 36.6 mmESP8266-WebRadio, the printed circuit board in 3D

    ESP8266-WebRadio

    karawin/Ka-Radio

    A wifi webradio with only low cost boards ESP8266 and VS1053 by Jp Cocatrix

    52 parts453
  • 2 layers95.2 × 57.2 mmDomesdayDuplicator, the printed circuit board in 3D

    DomesdayDuplicator

    Domesday86/DomesdayDuplicator

    High-speed LaserDisc RF sampler

    66 parts325GPL-3.0
  • 2 layers189.5 × 204.9 mmSmartSpin2k Panelized, the printed circuit board in 3D

    SmartSpin2k Panelized

    doudar/SmartSpin2k

    Transform your spin bike into a Smart Trainer!

    749 parts292GPL-2.0
  • 4 layers121.9 × 109.2 mmPlinkyblack hwmidi jacks, the printed circuit board in 3D

    Plinkyblack hwmidi jacks

    plinkysynth/plinky_public

    a public release of the plinky sw and hw

    300 parts227
  • 4 layers113.5 × 105.5 mmMultistepper, the printed circuit board in 3D

    Multistepper

    eddyem/stm32samples

    Code samples and ready projects based on bare-metal STM32

    243 parts208
  • 2 layers275 × 103 mmKeebee, the printed circuit board in 3D

    Keebee

    blakesmith/embedded

    Blake's embedded projects

    159 parts167
  • 2 layers43 × 34.3 mmEspway, the printed circuit board in 3D

    Espway

    espway/espway

    Segway-like robot implemented on ESP8266

    37 parts122LGPL-3.0

Questions

How big is the Basicesp PCB?

It measures 35.6 × 47 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Basicesp use?

11 parts, built around the LM1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Basicesp KiCad files?

From the wjblack/basicesp repository on GitHub, at the commit this page was made from: the board is rev1/kicad/basicesp.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Basicesp design in my own project?

Its repository publishes it under the WTFPL licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).