
Adapter
weiszpal/fpga-floppy
FPGA interface board to use an IBM PC floppy disk drive as any C64 comatible FDD

FPGA interface board to use an IBM PC floppy disk drive as any C64 comatible FDD
Interface board is an open-source printed circuit board by weiszpal, from the weiszpal/fpga-floppy repository on GitHub. It is a 2-layer board of 111.5 × 41.4 mm with 38 parts on 72 nets, routed with 343 tracks and 5 vias.
It is built around the 74LVC14AD and BC337. Its parts include 23 resistors, 4 capacitors, 4 ICs, 4 connectors and 1 transistor. It belongs with the interfaces and adapters boards and the FPGA and CPLD boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 20 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4, R5, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R21 +4 |
| 4 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4 |
| 2 | 680 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R22, R23 |
| 2 | 74LS06 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U1, U3 |
| 2 | 74LVC14 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U2, U4 |
| 1 | 5V_PWR | Connector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_Vertical | J2 |
| 1 | BC337 | Package_TO_SOT_THT:TO-92_Inline_Wide | Q1 |
| 1 | FPGA_devboard | Connector_PinSocket_2.54mm:PinSocket_2x22_P2.54mm_Vertical | J1 |
| 1 | GREEN | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D_ACT1 |
| 1 | IBM PC floppy disk drive connector | Connector_IDC:IDC-Header_2x17_P2.54mm_Vertical | J4 |
| 1 | R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R20 |
| 1 | RED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D_PWR1 |
| 1 | Serial IEEE-488 Bus | MAB6H:MAB6H | J3 |

weiszpal/fpga-floppy
FPGA interface board to use an IBM PC floppy disk drive as any C64 comatible FDD


robfinch/Cores
Cores ===== RTF's Cores Use at your own risk. Welcome to my galaxy of cores. Contained in the directories are IP cores, source code for digital circuits.


BlakeGarner/encoders-for-etc-eos
A 9-encoder (un-official) add on to the ETC Eos Family of Lighting Consoles and Software, using OSC over USB

fwachsmuth/Filmkorn-Raw-Scanner
The Filmkorn Raw Scanner, turning 8mm and 16mm films into lossless 12-bit CinemaDNG

fachat/csa_ultracpu
The CPU board for a 17MHz Colour-PET clone with modern interfaces


richard42/ESP32FloppyTester
A software/hardware tool for testing vintage floppy disk drives
It measures 111.5 × 41.4 mm and has 2 copper layers, 1.6 mm thick.
38 parts, built around the 74LVC14AD and BC337. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the weiszpal/fpga-floppy repository on GitHub, at the commit this page was made from: the board is interface_board/interface_board.kicad_pcb and its schematic adapter/adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask weiszpal before reusing the design.