
Kinect
mhered/KiCAD_udemy_course
My notes on the course "PCB design with KiCAD - updated for KiCAD 9" by Dr Peter Dalmaris in Udemy

This repository contains a PCB and a basic case for using only the camera board from the Xbox 360 Kinect.
Kinect is an open-source printed circuit board by vojtapl, from the vojtapl/xbox360-kinect-lite repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 78 × 24 mm with 21 parts on 15 nets, routed with 107 tracks and 39 vias.
It is built around the AP63203WU, LM3670MFX-1.8 and USBLC6-2SC6. Its parts include 6 capacitors, 3 ICs, 2 resistors, 2 connectors and 2 inductors.
This repository contains a PCB and a basic case for using only the camera board from the Xbox 360 Kinect.
I have recently read this great article, which lays out the idea of making a Kinect Lite from an old Xbox 360 Kinect by isolating the camera board, which can function separately. As I saw one being sold for next to nothing with a broken tilt motor, I thought it would be a great idea to implement the ideas mentioned in the article. The repository contains the PCB (including LCSC part numbers), which generates all the necessary voltage rails, and a basic 3D-printable case.



The measurements were made with KWS-2301C, a cheap USB-C power meter.

freenect-regview

On the ruler look at the top scale, as that one is in centimeters.




| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C7 |
| 2 | 22u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C5, C6 |
| 2 | 5K1 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 2 | L 4u7 | Inductor_SMD:L_1008_2520Metric_Pad1.43x2.20mm_HandSolder | L1, L2 |
| 2 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_DIN965_Pad | H1, H2 |
| 1 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4 |
| 1 | 1V8 | TestPoint:TestPoint_Loop_D2.50mm_Drill1.85mm | TP1 |
| 1 | 3V3 | TestPoint:TestPoint_Loop_D2.50mm_Drill1.85mm | TP2 |
| 1 | 5V | TestPoint:TestPoint_Loop_D2.50mm_Drill1.85mm | TP3 |
| 1 | AP63203WU | Package_TO_SOT_SMD:TSOT-23-6 | U2 |
| 1 | Female Header 2x5P, P=1.27mm | Connector_PinSocket_1.27mm:PinSocket_2x05_P1.27mm_Vertical | J3 |
| 1 | GND | TestPoint:TestPoint_Loop_D2.50mm_Drill1.85mm | TP4 |
| 1 | LM3670MFX-1.8 | Package_TO_SOT_SMD:TSOT-23-5 | U1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6_Handsoldering | U3 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J2 |

mhered/KiCAD_udemy_course
My notes on the course "PCB design with KiCAD - updated for KiCAD 9" by Dr Peter Dalmaris in Udemy


Dschadu/Geistwerk-BigCore
An ESP32-based open hardware control board designed for Bottango-powered animatronic and motion projects.

AronASzucs/Avalanche32
Handheld ESP32-S3 Geiger counter with a firmware-regulated 400 V boost, SBM-20 tube, USB-C charging and OLED display.

Bhakti-A/Maya_V_FlightController
This is a custom flight controller PCB designed for drones.

lightsource-nz/crossfire_mk5
crossfire: USB-MIDI forwarding agent for embedded USB-MIDI smart hubs


AntoG00/ESP32-C6-CO2-Monitor
Low-power CO2, temperature and humidity monitor using ESP32-C6 and E-Paper display.
It measures 78 × 24 mm and has 2 copper layers, 1.6 mm thick.
21 parts, built around the AP63203WU, LM3670MFX-1.8 and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the vojtapl/xbox360-kinect-lite repository on GitHub, at the commit this page was made from: the board is pcb/kinect.kicad_pcb and its schematic pcb/kinect.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).