

Picoballoon
- Size
- 55 × 63 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 97
- Nets
- 98
- Pads
- 313
- Tracks, vias
- 439, 489
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 15 Oct 2024
- Updated
- 20 May 2025
Overview
Picoballoon is an open-source printed circuit board by vojt444, from the vojt444/picoballoon repository on GitHub. It is a 4-layer board of 55 × 63 mm with 97 parts on 98 nets, routed with 439 tracks and 489 vias.
It is built around the MPL3115A2R1, HTU21D and MAX-M10S. Its parts include 34 capacitors, 19 resistors, 6 ICs, 6 inductors and 3 diodes.
Main components
3MPL3115A2R1
LGA-8(3x5)-40℃~+85℃ 0.05Kpa 0.4Kpa 1.95V~3.6V 1s 2uA 50Kpa~1.1bar I2C LGA-8(3x5) Pressure Sensors ROHSNXP SemiconductorsPressure SensorsHTU21D
DFN-6-EP(3x3)-40℃~+125℃ 0%RH~100%RH 1.5V~3.6V 450uA 8bit、12bit、14bit Factory calibration、Built-in temperature and humidity compensation、Built-in heater、Derived quantity calculation I2C ±0.3℃ ±2%RH DFN-6-EP(3x3) Temperature and Humidity Sensor ROHSTE ConnectivityTemperature And Humidity SensorMAX-M10S
LCC-18_10.1X9.7LCC-18_10.1X9.7 New Arrivals ROHSu-bloxUncategorised
Parts
97| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C5, C7, C9, C14, C15, C16, C18, C19, C20, C21, C23, C24, C25, C27, C37 |
| 13 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R3, R4, R5, R6, R7, R8, R9, R10, R12, R13, R15, R16 |
| 7 | 10u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3, C4, C11, C12, C13, C22 |
| 5 | , , , , | ||
| 4 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C6, C8, C10, C28 |
| 4 | MountingHole | MountingHole:MountingHole_2.1mm | H1, H2, H3, H4 |
| 2 | 100p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C26, C29 |
| 2 | 1M | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R17, R18 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R14 |
| 2 | 25p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C31, C33 |
| 2 | 74,74n | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L7, L8 |
| 2 | FerriteBead | Library:BLM21AG102BH1J | FB1, FB3 |
| 2 | GND | TestPoint:TestPoint_Pad_D2.0mm | TP9, TP10 |
| 2 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2, D3 |
| 1 | +3.3VA_TP | TestPoint:TestPoint_Pad_D2.0mm | TP1 |
| 1 | +3.3V_TP | TestPoint:TestPoint_Pad_D2.0mm | TP2 |
| 1 | 0 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R19 |
| 1 | 10 F | Library:Supercap_7.5mm | C1 |
| 1 | 106n | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L6 |
| 1 | 12n | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L5 |
| 1 | 14,35p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C30 |
| 1 | 300 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11 |
| 1 | 30M | Library:ECS3002030BDUTR | Y1 |
| 1 | 4.7u | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L1 |
| 1 | 43,06p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C32 |
| 1 | 552n | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L4 |
| 1 | ADC | TestPoint:TestPoint_Pad_D2.0mm | TP3 |
| 1 | Antenna | Library:BNC_Connector_PCB | AE2 |
| 1 | Antenna | Library:RECE20369001E01 | AE1 |
| 1 | Conn_01x02 | Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_Vertical | J2 |
| 1 | D_Schottky | Diode_SMD:Nexperia_CFP3_SOD-123W | D1 |
| 1 | EXT_DEBUGGER | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical | J1 |
| 1 | HTU21D | Library:SON100P300X300X100-7N-D | HM1 |
| 1 | MAX-M10S | RF_GPS:ublox_MAX | U5 |
| 1 | MCP9802 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | MCXC141VLH | Package_QFP:LQFP-64-1EP_10x10mm_P0.5mm_EP5x5mm | IC1 |
| 1 | MISO | TestPoint:TestPoint_Pad_D2.0mm | TP8 |
| 1 | MOSI | TestPoint:TestPoint_Pad_D2.0mm | TP7 |
| 1 | MPL3115A2 | Package_LGA:NXP_LGA-8_3x5mm_P1.25mm_H1.1mm | U2 |
| 1 | OPA333xxDBV | Package_TO_SOT_SMD:SOT-23-5 | U6 |
| 1 | SCLK | TestPoint:TestPoint_Pad_D2.0mm | TP6 |
| 1 | SCL_TEMP | TestPoint:TestPoint_Pad_D2.0mm | TP5 |
| 1 | SDA_TEMP | TestPoint:TestPoint_Pad_D2.0mm | TP4 |
| 1 | Si4461 | Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.6x2.6mm_ThermalVias | U1 |
| 1 | Solar_Cell | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | SC1 |
| 1 | TPS61097A-33DBVR | Library:SOT95P280X145-5N | PS1 |
| 1 | xx | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C17 |
More from vojt444/picoballoon
3- 4 layers43 × 45 mm

- 4 layers58.4 × 42 mm

- 2 layers48.4 × 25.5 mm

Similar boards
- 2 layers93 × 42 mm

ADEM
timelab/ADEM
Mobile device for distributed measurements of particulate matter (fine dust)
29 parts13LGPL-3.0 - 2 layers70 × 40 mm

MoreE u blox E PEAS
ldab/Node-RED-Energy-Harvesting-dashboard
Node-RED Energy Harvesting dashboard example, weather forecast, temperature and humidty measurement. MQTT, ESP32, u-blox NINA-W10, HTU21D, IBM Cloud, CloudMQTT
43 parts11MIT - 2 layers50 × 100 mm

OpenWeatherStation MainBoard
VitalSeptfonds/OpenWeatherStation
Open Wheather Station based on STM32
111 parts2MIT - 2 layers29 × 57 mm

- 2 layers26.4 × 36.1 mm

Sensof ht
dimhoff/sensof
Si4010 based wireless sensors(temperature, humidity, etc.) firmware and utilities
24 parts1 - 2 layers31 × 130 mm

Handheld unit old3
zegarac/Photosynq-hardware
Photosynq KiCad files for the main board and other associated hardware
127 parts1GPL-3.0 - 2 layers50 × 35 mm

- 4 layers75 × 84.8 mm

Questions
How big is the Picoballoon PCB?
It measures 55 × 63 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Picoballoon use?
97 parts, built around the MPL3115A2R1, HTU21D and MAX-M10S. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Picoballoon KiCad files?
From the vojt444/picoballoon repository on GitHub, at the commit this page was made from: the board is HW/picoballoon_v1/picoballoon.kicad_pcb and its schematic HW/aprs_test_board/aprs_test_board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Picoballoon design in my own project?
Its repository states no licence, so its author keeps all rights: ask vojt444 before reusing the design.