2 layers
Projeto modificado
luispaulomr/alr3000z_firmware
Firmware for ALR3000z (development board based on PIC18F4550).
68 parts
2 layers
Pinguicaro
valentinbasel/icaro-pcb5icaro-pcb
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 82
- Nets
- 69
- Pads
- 304
- Tracks, vias
- 1,067, 10
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 4 Jun 2014
- Updated
- 27 Feb 2018
Overview
Pinguicaro is an open-source printed circuit board by valentinbasel, from the valentinbasel/icaro-pcb repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board with 82 parts on 69 nets, routed with 1,067 tracks and 10 vias.
It is built around the PIC18F2550-I/SP, PIC18F4550-I/P and L293D, with the 78L05 and LM7805 among its other parts. Its parts include 19 connectors, 16 resistors, 14 diodes, 13 capacitors and 10 switches. It belongs with the PIC boards of this library.
Main components
5
PIC18F2550-I/SP
SPDIP-28-40℃~+85℃ 10bit 24 256Byte 2KB 32KB 4.2V~5.5V 48MHz 8 Bit Built-in FLASH PIC SPDIP-28 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
PIC18F4550-I/P
PDIP-40-40℃~+85℃ 10bit 256Byte 2KB 32KB 35 4.2V~5.5V 48MHz 8 Bit Built-in FLASH PIC PDIP-40 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
L293D
DIP-16-40℃~+150℃ 1.2A 2 4.5V~36V 4mA 600mA DIP-16 Brushed DC Motor Drivers ROHSSTMicroelectronicsStepper Motor Driver
78L05
SOT-89-3-20℃~+120℃@(Tj) 1 1.7V 100mA 2mA 30V 40uV 49dB@(120Hz) 5V Fixed Over Temperature Protection、Short Circuit Protection Positive SOT-89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSUMWVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
LM7805
TO-2630℃~+125℃ 1 1A 20V 2V 42uV 5V 62dB@(120Hz) 8mA Fixed Over Temperature Protection、Short Circuit Protection Positive TO-263 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSYONGYUTAIVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdicaro-pcb
icaro-pcb
Parts
82| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 470 | R4 | R1, R2, R3, R4, R5, R6, R7, R8, R9, R12, R17 |
| 11 | LED | LED-5MM | D1, D2, D3, D4, D5, D6, D7, D8, D10, D11, D13 |
| 5 | 0.1uF | C1 | C9, C10, C11, C12, C13 |
| 5 | 1k | R4 | R11, R13, R14, R15, R16 |
| 4 | 100uF-electr | C1V5 | C4, C6, C7, C8 |
| 4 | P*** | 1pin | 1PIN, 1PIN, 1PIN, 1PIN |
| 3 | 1n4007 | D3 | D9, D12, D14 |
| 2 | 22pF | C1 | C2, C3 |
| 2 | CONN_2 | SIL-2 | P15, P16 |
| 2 | ON/OFF | SIL-3 | SW1, SW3 |
| 2 | SELECTOR_V | PIN_ARRAY_3X1 | K1, K8 |
| 1 | 10uF-electr | C1V5 | C5 |
| 1 | 220nF | C1 | C1 |
| 1 | 78L05 | LM78XX-TO92 | U5 |
| 1 | CONN_4 | SIL-4 | P5 |
| 1 | CRYSTAL | Crystal_HC50-U_Vertical_RevA_09Aug2010 | X1 |
| 1 | DC_IN | bornier2 | P10 |
| 1 | DC_out | SIL-2 | P17 |
| 1 | GND | SIL-8 | P3 |
| 1 | L293D | DIP-16__300_ELL | U3 |
| 1 | LM7805 | LM78XX | U4 |
| 1 | MOTOR_1 | bornier2 | P8 |
| 1 | MOTOR_2 | bornier2 | P9 |
| 1 | PIC18F2550 | DIP-28__300_ELL | U1 |
| 1 | PIC18F4550 | DIP-40__600_ELL | U2 |
| 1 | PORT_B | SIL-8 | P7 |
| 1 | RESET | SW_PUSH_SMALL | SW2 |
| 1 | SALIDA_UNL2803 | SIL-8 | P1 |
| 1 | SENS_ANALOG | SIL-8 | P4 |
| 1 | SERVO_1 | PIN_ARRAY_3X1 | K2 |
| 1 | SERVO_2 | PIN_ARRAY_3X1 | K3 |
| 1 | SERVO_3 | PIN_ARRAY_3X1 | K4 |
| 1 | SERVO_4 | PIN_ARRAY_3X1 | K5 |
| 1 | SERVO_5 | PIN_ARRAY_3X1 | K6 |
| 1 | UNL2803 | DIP-18__300_ELL | P6 |
| 1 | USB_2 | USB_B | J1 |
| 1 | VCC | SIL-8 | P2 |
| 1 | jmp_d14 | SIL-2 | P18 |
| 1 | sn_d1 | bornier2 | P11 |
| 1 | sn_d2 | bornier2 | P12 |
| 1 | sn_d3 | bornier2 | P13 |
| 1 | sn_d4 | bornier2 | P14 |
Questions
What parts does the Pinguicaro use?
82 parts, built around the PIC18F2550-I/SP, PIC18F4550-I/P, L293D and 78L05. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pinguicaro KiCad files?
From the valentinbasel/icaro-pcb repository on GitHub, at the commit this page was made from: the board is kicad/pinguicaro.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pinguicaro design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers99.7 × 49.5 mm
- 2 layers
- 2 layers100 × 50 mm
Pinguino-2550
MefhigosetH/pinguino-boards
Personal repository of schematics and boards related to Pinguino Project.
28 parts3Unlicense - 2 layers69.2 × 48.3 mm
- 2 layers69.9 × 79.4 mm
10x10cm Pinguino SMD-2550
fandres/pinguino_SMD-2550
PCB in surface mount of the Pinguino board based on the microcontroller PIC18F2550
114 parts - 2 layers88.9 × 98.5 mm
- 2 layers
