

Robotics Board
Stellenbosch Robotics dEvelopment Board
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 100
- Nets
- 97
- Pads
- 594
- Tracks, vias
- 1,007, 20
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 3
- Created
- 13 Feb 2014
- Updated
- 11 Sep 2014
Overview
Robotics Board is an open-source printed circuit board by KolijnWolfaardt, from the KolijnWolfaardt/SREB repository on GitHub. It is a 2-layer board with 100 parts on 97 nets, routed with 1,007 tracks and 20 vias.
It is built around the PIC18F4550-I/P and FT230XQ-R. Its parts include 24 connectors, 22 capacitors, 16 diodes, 15 resistors and 7 switches. It belongs with the robots and motor control and microcontroller boards boards and the PIC boards of this library.
Main components
2PIC18F4550-I/P
PDIP-40-40℃~+85℃ 10bit 256Byte 2KB 32KB 35 4.2V~5.5V 48MHz 8 Bit Built-in FLASH PIC PDIP-40 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)FT230XQ-R
QFN-16-EP(4x4)-40℃~+85℃ 125uA 3.3V~5V 8mA USB 2.0 USB to UART QFN-16-EP(4x4) USB Converters ROHSFTDIUSB Converters
README
README.mdSREB
Stellenbosch Robotics dEvelopment Board
This board is based on the PIC18f4550 microcontroller. The board itself was designed for the Stellenbosch Robotics club, to server as a replacement for the UNO32 development board.
The circuit board and layout were done using KiCad (2013-05-18 BZR 4017)-stable. Additional component libraries and footprints were created using KiCad, and placed in ./lib The Open Source Hardware logo was downloaded from http://oshwlogo.com/, and is included in ./lib
Copyright Kolijn Wolfaardt 2013. This documentation describes Open Hardware and is licensed under the CERN OHL v. 1.2. You may redistribute and modify this documentation under the terms of the CERN OHL v.1.2. (http://ohwr.org/cernohl). This documentation is distributed WITHOUT ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING OF MERCHANTABILITY, SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE. Please see the CERN OHL v.1.2 for applicable conditions
Parts
100| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | CONN_12 | SIL-12-No-Silk | P5, P6, P7, P12, P14, P16, P17, P18, P19, P20, P21, P22 |
| 9 | DIODE | D4 | D1, D3, D4, D5, D6, D7, D8, D9, D10 |
| 8 | 100nF | C2 | C2, C8, C9, C12, C14, C20, C21, C22 |
| 7 | CONN_3 | SIL-3 | K1, K2, P1, P2, POW_SEL1, PWM1, PWM2 |
| 6 | 1uF | C1V5 | C1, C3, C5, C6, C13, C17 |
| 5 | 220 | R3 | R1, R5, R6, R7, R8 |
| 4 | CONN_1 | 1pin | MountingHole1, MountingHole2, MountingHole3, MountingHole4 |
| 4 | LED | LED-3MM | LED0, LED1, LED2, LED3 |
| 3 | CONN_12 | SIL-12 | P3, P4, P24 |
| 3 | CONN_8 | Pin_array_8x3 | P8, P9, P11 |
| 3 | DPST | SPST | BUT_0, BUT_1, Reset1 |
| 2 | 10k | R4 | R9, R10 |
| 2 | 10nF | C2 | C15, C16 |
| 2 | 10uF | C1V5 | C4, C7 |
| 2 | 1k | R3 | R2, R3 |
| 2 | 27 | R3 | R13, R14 |
| 2 | 270 | R3 | R11, R12 |
| 2 | 30pF | C1 | C10, C11 |
| 2 | 47pF | C1 | C18, C19 |
| 2 | CONN_6 | Pin_array_6x3 | P10, P13 |
| 1 | 10k | R3 | R4 |
| 1 | 18k | R3 | R15 |
| 1 | 3.3VREG | LM78XXV-NumberedPads | U5 |
| 1 | 4MHz | HC-49V | X1 |
| 1 | 7805 | LM78XXV | U1 |
| 1 | CONN_1 | OSHW-logo_silkscreen-front_10mm | OSHWLogoFront1 |
| 1 | CONN_1 | OSHW-logo_copper-back_10mm | OSHWLogoBack1 |
| 1 | CONN_1 | SIL-1 | P23 |
| 1 | CONN_5 | SIL-5 | P15 |
| 1 | CONN_6 | SIL-6 | ICSP1 |
| 1 | DC_IN | BARREL_JACK | CON1 |
| 1 | FT230X | ssop-16-extended | U4 |
| 1 | L293 | DIP-16__300 | U2 |
| 1 | PIC18F4550 | DIP-40__600 | U3 |
| 1 | Power_LED | LED-3MM | D2 |
| 1 | RxLED | LED-3MM | D12 |
| 1 | TxLED | LED-3MM | D11 |
| 1 | USB | USB_mantech | J1 |
Similar boards
- 2 layers

- 2 layers

- 2 layers88.9 × 98.5 mm

- 2 layers

Projeto modificado
luispaulomr/alr3000z_firmware
Firmware for ALR3000z (development board based on PIC18F4550).
68 parts - 2 layers

- 2 layers75 × 130 mm

- 8 layers120 × 60 mm

Jetson orin baseboard
antmicro/jetson-orin-baseboard
Baseboard targetting the NVIDIA Jetson Orin Nano and Jetson Orin NX
681 parts305Apache-2.0 - 4 layers22.5 × 30 mm

Questions
What parts does the Robotics Board use?
100 parts, built around the PIC18F4550-I/P and FT230XQ-R. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Robotics Board KiCad files?
From the KolijnWolfaardt/SREB repository on GitHub, at the commit this page was made from: the board is Robotics Board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Robotics Board design in my own project?
Its repository states no licence, so its author keeps all rights: ask KolijnWolfaardt before reusing the design.