

InputBuck 1B
- Size
- 67.2 × 46 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 45
- Nets
- 22
- Pads
- 142
- Tracks, vias
- 144, 50
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 21 Mar 2025
- Updated
- 19 Oct 2025
Overview
InputBuck 1B is an open-source printed circuit board by ut-ras, from the ut-ras/rm_electrical-supercap repository on GitHub. It is a 4-layer board of 67.2 × 46 mm with 45 parts on 22 nets, routed with 144 tracks and 50 vias.
It is built around the BQ24640RVA, BAT54 and BSC059N04LS6, with the LTST-C193KSKT-5A and LTST-C193TBKT-5A among its other parts. Its parts include 13 capacitors, 13 resistors, 4 diodes, 4 connectors and 2 transistors.
Main components
5BQ24640RVA
VQFN-16-EP(3.6x3.6)0℃~+125℃ 1.5mA 10A 2.1V 5V~28V Charging IC Supercapacitor Support Support 恒流充电、恒压充电、可编程充电电流、软启动、欠压锁定、Overcurrent Protection、过压保护 VQFN-16-EP(3.6x3.6) Battery Management ROHSTexas InstrumentsBattery ManagementBAT54
SOT-23200mA 2uA@25V 30V 800mV@100mA Independent SOT-23 Schottky Diodes ROHSFOSANSchottky DiodesBSC059N04LS6
TDSON-8FL-55℃~+175℃ 1 N-channel 2.3V 21pF 38W 40V 5.9mΩ@10V 59A 830pF 9.4nC@10V TDSON-8FL MOSFETs ROHSInfineon TechnologiesMOSFETsLTST-C193KSKT-5A
0603-55℃~+85℃ 130° 26.05mcd 2V 587nm~594.5nm 591nm 5mA 75mW Discrete Diode Water Clear Yellow 0603 LED Indication - Discrete ROHSLite-OnLED Indication - DiscreteLTST-C193TBKT-5A
0603-20℃~+80℃ 130° 15mcd 2.8V 465nm~475nm 468nm 5mA 76mW Blue Discrete Diode Water Clear 0603 LED Indication - Discrete ROHSLite-OnLED Indication - Discrete
README
README.mdrm_electrical-supercap
Parts
45| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 10u | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C2, C5, C6, C7 |
| 3 | 0.1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9, C10, C13 |
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C11, C12 |
| 2 | 0 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R5 |
| 2 | 4.7k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8, R9 |
| 2 | BAT54 | Package_TO_SOT_SMD:SOT-23_Handsoldering | D1, D2 |
| 2 | BSC059N04LS6 | Package_SON:Infineon_PG-TDSON-8_6.15x5.15mm | Q1, Q2 |
| 2 | V_{LODRV} | TestPoint:TestPoint_Bridge_Pitch2.0mm_Drill0.7mm | TP4, TP6 |
| 2 | XT30_F | Connector_AMASS:AMASS_XT30U-F_1x02_P5.0mm_Vertical | J14, J15 |
| 1 | 0.01 | Resistor_SMD:R_0612_1632Metric_Pad1.18x3.40mm_HandSolder | R3 |
| 1 | 15k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7 |
| 1 | 15p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C8 |
| 1 | 2.2u | Capacitor_THT:C_Radial_D5.0mm_H11.0mm_P2.00mm | C3 |
| 1 | 27k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4 |
| 1 | 4.7u | Inductor_SMD:L_Bourns_SRN8040TA | L1 |
| 1 | 430k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R12 |
| 1 | 470k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 1 | 47k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13 |
| 1 | 6.8 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 82k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11 |
| 1 | 9.31k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10 |
| 1 | BQ24640 | ! Robomaster ICs:QFN50P350X350X100-17N-D | U1 |
| 1 | Conn_01x01_Pin | Connector_Wire:SolderWire-2.5sqmm_1x01_D2.4mm_OD3.6mm | J23 |
| 1 | Conn_01x02_Socket | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J1 |
| 1 | LOGO | ! Robomaster Special:StampedeLogo | G*** |
| 1 | LTST-C193KSKT-5A | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D4 |
| 1 | LTST-C193TBKT-5A | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3 |
| 1 | V_{HIDRV} | TestPoint:TestPoint_Bridge_Pitch2.0mm_Drill0.7mm | TP1 |
| 1 | V_{N} | TestPoint:TestPoint_Bridge_Pitch2.0mm_Drill0.7mm | TP5 |
| 1 | V_{P} | TestPoint:TestPoint_Bridge_Pitch2.0mm_Drill0.7mm | TP3 |
| 1 | V_{SW} | TestPoint:TestPoint_Bridge_Pitch2.0mm_Drill0.7mm | TP2 |
More from ut-ras/rm_electrical-supercap
12- 2 layers

- 2 layers109 × 90 mm

- 4 layers97.5 × 69.8 mm

- 4 layers46 × 97 mm

- 4 layers46 × 71.2 mm

- 4 layers71.2 × 46 mm

- 2 layers55 × 45.1 mm

- 4 layers111.8 × 57.9 mm

- 4 layers45.6 × 65.2 mm

- 2 layers48 × 46.5 mm

- 2 layers40.4 × 57.8 mm

- 2 layers64.2 × 49.3 mm

Similar boards
- 6 layers188 × 66.8 mm

U2CEM
oxidecomputer/hw-k2
This design provides a PCIe extender that converts from a U.2 PCIe device connector and provides a x4 PCIe CEM slot.
24 partsMPL-2.0 - 2 layers252.9 × 55 mm

- 4 layers101.2 × 24 mm

Charger module
mikesmitty/power-manifold
Six-port USB-C power supply: up to 100 W per port from one 24 V supply, with per-port control, priority-based power sharing and Home Assistant support. 100% local, no cloud required.
90 parts3MIT - 4 layers40 × 40 mm

BatteryCharger
BlockWorker/ModularAudio
Compact, modular, versatile, hi-fi audio system concept.
49 parts2 - 2 layers78 × 36 mm

Bt nes advantage pcb
cajunpanda/bluetooth-nes-advantage
A bluetooth mod for the NES Advantage classic controller.
45 parts7MIT - 4 layers90 × 90 mm

- 4 layers50 × 16 mm

System board
proegssilb/lightsaber-hardware
PCBs and other files for lightsaber soundboard hardware.
72 parts2CERN-OHL-S-2.0 - 4 layers98.2 × 122 mm

Project Roll
kevleep/Project-Roll
Project Roll Project Roll is a spherical robot that achieves omni-directional movement using omni-wheels and a hamster ball drive mechanism.
75 parts
Questions
How big is the InputBuck 1B PCB?
It measures 67.2 × 46 mm and has 4 copper layers, 1.6 mm thick.
What parts does the InputBuck 1B use?
45 parts, built around the BQ24640RVA, BAT54, BSC059N04LS6 and LTST-C193KSKT-5A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the InputBuck 1B KiCad files?
From the ut-ras/rm_electrical-supercap repository on GitHub, at the commit this page was made from: the board is Rev 1B Boards/InputBuck 1B/InputBuck 1B.kicad_pcb and its schematic Rev 1 Boards/Boost Stage1 Rev1/Stage1 Rev1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the InputBuck 1B design in my own project?
Its repository states no licence, so its author keeps all rights: ask ut-ras before reusing the design.