2 layers100 × 80 mm
2 layers99.8 × 99.9 mm
SignalGenerator
ukmaker/SignalGenerator1Signal generator based on AD9850, AD603 and Arduino Nano
- Size
- 99.8 × 99.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 117
- Nets
- 87
- Pads
- 390
- Tracks, vias
- 52, 2
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 7 May 2017
- Updated
- 12 Aug 2017
Overview
SignalGenerator is an open-source printed circuit board by ukmaker, from the ukmaker/SignalGenerator repository on GitHub. It is a 2-layer board of 99.8 × 99.9 mm with 117 parts on 87 nets, routed with 52 tracks and 2 vias.
It is built around the ATMEGA328-AU and KBP206G. Its parts include 47 capacitors, 29 resistors, 16 ICs, 9 connectors and 6 inductors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
2
ATMEGA328-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)KBP206G
KBP-55℃~+150℃@(Tj) 1.1V@2A 2A 55A 5uA@600V 600V Single-Phase Rectifier KBP Bridge Rectifiers ROHSShandong Jingdao MicroelectronicsBridge Rectifiers
README
Controller/V2/README.mdChanges from V1:
Correct connection of SDA and SCL to Arduino Nano
Parts
117| Qty | Value | Footprint | References |
|---|---|---|---|
| 30 | C | Capacitors_SMD:C_0603_HandSoldering | C11, C13, C15, C17, C19, C23, C24, C25, C26, C27, C28, C29, C30, C31, C32, C33 +14 |
| 26 | R | Resistors_SMD:R_0603_HandSoldering | R1, R2, R10, R11, R12, R13, R17, R19, R20, R21, R22, R24, R25, R26, R27, R28 +10 |
| 10 | Csmall | Capacitors_SMD:C_0603_HandSoldering | C1, C2, C3, C4, C12, C14, C20, C36, C48, C49 |
| 6 | L_Small | Resistors_SMD:R_0603_HandSoldering | L1, L2, L3, L4, L5, L6 |
| 3 | 1U MLCC | Capacitors_SMD:C_0603_HandSoldering | C10, C18, C41 |
| 3 | CONN_01X02 | SparkFun-Connectors:1X02 | P6, P7, P8 |
| 3 | POT | Pin_Headers:Pin_Header_Straight_1x03 | RV1, RV2, RV3 |
| 2 | 0R | Resistors_SMD:R_0603_HandSoldering | R16, R18 |
| 2 | 10U MLCC | Capacitors_SMD:C_1206_HandSoldering | C43, C44 |
| 2 | 7805 | TO_SOT_Packages_THT:TO-92_Inline_Wide | U9, U11 |
| 2 | 7905 | TO_SOT_Packages_THT:TO-92_Inline_Wide | U10, U12 |
| 2 | AD603 | Housings_SSOP:MSOP-8_3x3mm_Pitch0.65mm | U6, U7 |
| 2 | BNCPTH | SparkFun-Connectors:BNC | J2, J3 |
| 2 | CP | Capacitors_ThroughHole:C_Radial_D8_L13_P3.8 | C21, C22 |
| 2 | LED | LEDs:LED_0603 | D4, D5 |
| 2 | LM741 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U13, U15 |
| 1 | 1k5 | Resistors_SMD:R_0603_HandSoldering | R8 |
| 1 | 7805 | TO_SOT_Packages_THT:TO-220_Neutral123_Horizontal_LargePads | U8 |
| 1 | AD5592R | Housings_SSOP:TSSOP-16_4.4x5mm_Pitch0.65mm | U2 |
| 1 | AD9850_DDS_Module | UKMaker:AD9850_DDS_Module | U5 |
| 1 | ATMEGA328-A | Housings_QFP:TQFP-32_7x7mm_Pitch0.8mm | IC1 |
| 1 | BNCPTH | Sockets_BNC:BNC_Socket_TYCO-AMP_LargePads | J1 |
| 1 | CONN_01X03 | SparkFun-Connectors:SCREWTERMINAL-5MM-3 | P5 |
| 1 | CONN_02X03 | Pin_Headers:Pin_Header_Straight_2x03 | P1 |
| 1 | Crystal_Small | Crystals:Crystal_HC50-U_Vertical | Y1 |
| 1 | D | Diodes_SMD:D_0805 | D3 |
| 1 | FT232RLSSOP | Housings_SSOP:SSOP-28_5.3x10.2mm_Pitch0.65mm | U4 |
| 1 | KBP206G | UKMaker:BridgeRectifier_2KBP | D1 |
| 1 | Q_NMOS_SDG | TO_SOT_Packages_SMD:SOT-23 | Q1 |
| 1 | RELAY-G5V-1 | SparkFun:SparkFun-RELAY-G5V | U16 |
| 1 | Serial_LCD_16x2 | SparkFun-Connectors:1X04 | U3 |
| 1 | TRANSFO2 | UKMaker:MyrraTransformer_30x15.5 | T1 |
| 1 | Tri-Colour_Rotary_Encoder | SparkFun:SparkFun-1X08 | U1 |
| 1 | USB_B | Connect:USB_B | P2 |
More from ukmaker/SignalGenerator
3- 2 layers99.7 × 70 mm
- 2 layers95.9 × 75.1 mm
Similar boards
- 2 layers176.4 × 133.2 mm
MainPCB v0.92
FilmNeverDie/Farbung
A open source project based on FilmNeverDie's CP800 film processing machine
207 parts25BSD-3-Clause - 2 layers94.1 × 121.9 mm
SCH PowerSupply
UAA-F14/PCBs-Design
Power electronics PCB coursework — SCR controller, buck converter, Class D amplifier, DC-AC inverter, and a protected power supply Resources
47 parts1 - 2 layers98 × 50 mm
- 2 layers82 × 120 mm
Sample Numeric Keyboard
famichu/MagLev_Switch_MX
The 3D printable magnetic levitation contactless switch with the linear output hall effect sensor.
66 parts467 - 2 layers76.2 × 76.2 mm
PaperBack Converter
dqydj/PaperBack_EPaper_Display
Internet Connected or Standard Input EPaper Display
92 parts83MIT - 2 layers18 × 33.2 mm
Arduino pro mini
etimou/arduino-pro-mini-kicad
This is a clone of the well known arduino board "pro-mini" designed in kicad while the original was designed in eagle. Ref https://store.arduino.cc/arduino-pro-mini
23 parts69 - 2 layers101.6 × 147.3 mm
Karabas pro revER
andykarpov/karabas-pro
FPGA based retrocomputer with FDD and HDD controllers
223 parts37MIT - 4 layers100 × 100 mm
Questions
How big is the SignalGenerator PCB?
It measures 99.8 × 99.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the SignalGenerator use?
117 parts, built around the ATMEGA328-AU and KBP206G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the SignalGenerator KiCad files?
From the ukmaker/SignalGenerator repository on GitHub, at the commit this page was made from: the board is KiCad/SignalGenerator.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the SignalGenerator design in my own project?
Its repository states no licence, so its author keeps all rights: ask ukmaker before reusing the design.