

Differential Probe
High-voltage differential probe PCB — KiCAD design
- Size
- 95 × 57 mm
- Copper layers
- 2
- Thickness
- 2.63 mm
- Parts
- 97
- Nets
- 58
- Pads
- 273
- Tracks, vias
- 372, 154
- Pours
- 360
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 18 Sep 2026
- Updated
- 1 Oct 2026
Overview
Differential Probe is an open-source printed circuit board by ugo-silato, from the ugo-silato/Differential-Probe repository on GitHub. It is a 2-layer board of 95 × 57 mm with 97 parts on 58 nets, routed with 372 tracks and 154 vias.
It is built around the ADA4817-1ARDZ-R7, MAX1555EZK+T and BAV99, with the SMBJ5.0A among its other parts. Its parts include 38 resistors, 33 capacitors, 5 ICs, 5 diodes and 5 connectors. It belongs with the sensors and measurement boards of this library.
Main components
4ADA4817-1ARDZ-R7
SOIC-8-EP-40℃~+105℃ -5V~5V -83dB 1 14mA 2pA 40mA 410MHz 4nV/√Hz@100kHz 500uV 5V~10V 7uV/℃ 870V/us Enable/shutdown function SOIC-8-EP FET Input Amplifiers ROHSAnalog DevicesOperational AmplifierMAX1555EZK+T
TSOT-23-5-40℃~+85℃ 1 3.7V~7V 340mA 4.2V 5uA Charging IC Lithium Battery Not supported TSOT-23-5 Battery Management ROHSMaxim Integrated (Analog Devices)Battery ManagementBAV99
SOT-231 Pair Series Connection 1.25V@150mA 100V 215mA 250mW 4A 4ns 500nA@80V SOT-23 Switching Diodes ROHSNexperiaSwitching DiodesSMBJ5.0A
DO-214AA(SMB)-65℃~+150℃ 5V 600W@10/1000us 65.3A@10/1000us 7V 800uA 9.2V TVS Unidirectional DO-214AA(SMB) ESD and Surge Protection (TVS/ESD) ROHSMDDESD And Surge Protection (TVS/ESD)
README
README.mdDifferential Probe
A high-voltage, active differential probe for floating measurements with selectable 10x/100x attenuation.
Hardware Overview
Specifications
- Input impedance: 1 MΩ || ~50 pF per channel
- Common Mode Voltage:
- Single-ended (per input, referenced to GND): ±300 VAC or ±500 VDC
- Differential (between two inputs): ±300 VAC or ±500 VDC channel-to-channel
- Bandwidth: As per Levido reference design (limited by compensation network)
- Attenuation: Selectable 10x / 100x
- Power: Li-ion battery (USB-C charging only)
- Output: Single-ended 50 Ω coaxial
Architecture
Input Stage (2 channels)
- BNC connectors (J1, J2)
- Compensated attenuator network (10x baseline, 100x with relay switching)
- Protection: BAV99 diode clamps (D1, D2), SMAJ5.0A TVS (D3), 0.5A fuse (F1)
Buffer & Summing Stage
- U1, U3: ADA4817-1ARDZ (1 GHz unity-gain stable op-amps, JFET input)
- U2: LMH6611 (345 MHz single-supply buffer) — differential summing amplifier
- Output on BNC (J3)
Power
- U4: MAX1555 (USB-C Li-ion charger — charging only)
- U5: TPS65133 (isolated ±5V rail generator from battery)
- Li-ion battery (internal, charged via J4 USB-C)
- Status LEDs: Green (charging), Red (full charge)
Design Highlights
- High input impedance JFET buffers prevent loading on the attenuation network
- Isolated floating operation — no ground reference needed at inputs
- Band-limited compensation — 10 pF high-Q caps in 1206 package for HV performance
- CMRR trimming — manual adjustments via potentiometers (R14, R17, R9, R35) for in-service calibration
- Thermal management — L1–L4 switching filters isolate DC/DC noise from analog rails
Project Structure
├── README.md (this file)
├── .gitignore
├── Differential Probe.kicad_pro (KiCAD project)
├── Differential Probe.kicad_sch (Schematic)
├── Differential Probe.kicad_pcb (PCB layout)
│
├── BOM/
│ ├── BOM.csv (KiCAD export)
│ └── BOM.xlsm (detailed with costs/sources)
│
├── dfm/
│ └── gerber/ (production-ready Gerber + drill)
│ ├── *.gbr, *.drl (layer files)
│ └── *-drl_map.pdf (drill legend)
│
├── docs/
│ ├── Sonda_differenziale_taratura_ITA.docx
│ └── Differential_probe_calibration_ENG.docx
│
├── Enclosure/ (3D CAD to be added)
│
├── production/
│ ├── bom.csv, positions.csv, designators.csv
│ └── netlist.ipc
│
└── fabrication-toolkit-options.jsonGetting Started
Assembly
- Use Gerber files in
dfm/gerber/for PCB manufacturing - Pick & Place file:
production/positions.csv - BOM:
BOM/BOM.csv(LCSC/Digi-Key references inBOM/BOM.xlsm)
Bring-up & Calibration
- See
docs/folder for calibration procedure (ITA/ENG) - Trim potentiometers (R14, R17, R9, R35) for CMRR balance
- Test points: TP1–TP4 for in-circuit measurements
Software
- No firmware code; purely analog probe
- Battery charging managed by MAX1555 (USB-C)
Testing & Measurements
(To be filled after validation)
- Bandwidth @ -3dB
- CMRR @ 1 MHz, 10 MHz, 50 MHz
- Slew rate
- Noise floor
Credits & Attribution
This probe design is derived from the High-Voltage Differential Probe by Andrew Levido, published in Circuit Cellar.
Key differences in this implementation:
- PCB layout: Entirely redesigned and laid out from scratch
- Manufacturing: Adapted for modern LCSC component sourcing and SMD assembly
- Validation: Fully tested and brought into production
The schematic topology and component selections follow Levido's design closely; credit for the original concept and circuit architecture belongs to him.
License
CERN-OHL-2.0-S — Open Hardware License
Contact & Contributions
For questions, improvements, or issues — open a GitHub Issue or contact the author.
Original Circuit Design: Andrew Levido (Circuit Cellar)
PCB Layout & Bring-up: Ugo Silato
Status: Fully operational (Rev. 1)
Last Updated: September 2026
Parts
97| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C10, C11, C12, C15, C17, C25, C27 |
| 8 | 10pF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C3, C4, C5, C6, C18, C19, C20, C21 |
| 8 | 1M Ohms | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R4, R5, R6, R7, R28, R29, R30, R31 |
| 4 | 10K Ohms | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10, R11, R23, R25 |
| 4 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C26, C28, C30, C33 |
| 4 | 4.7uH | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | L1, L2, L3, L4 |
| 4 | 500 Ohms | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R24, R27 |
| 3 | 0 Ohm | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R20, R33, R36 |
| 3 | 1K Ohms | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8, R26, R35 |
| 3 | 510 Ohms | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R32, R38 |
| 3 | Conn_Coaxial | PersonalFootprint_Library:BNC_Dosin-801-0078 | J1, J2, J3 |
| 2 | 0 Ohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R21, R34 |
| 2 | 100pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C16 |
| 2 | 120pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7, C22 |
| 2 | 15K Ohms | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12, R14 |
| 2 | 330pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8, C23 |
| 2 | 470uF 6.3V | Capacitor_SMD:CP_Elec_6.3x5.7 | C29, C32 |
| 2 | 8-50pF | Capacitor_SMD:C_Trimmer_Voltronics_JR | C9, C24 |
| 2 | 91 Ohms | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15, R22 |
| 2 | ADA4817-1ARDZ-R7 | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm_ThermalVias | U1, U3 |
| 2 | BAV99 | Package_TO_SOT_SMD:SOT-23 | D1, D2 |
| 2 | SW_Push_DPDT | Button_Switch_THT:SW_Push_2P2T_Toggle_CK_PVA2OAH5xxxxxxV2 | SW1, SW2 |
| 2 | Test Point | TestPoint:TestPoint_Pad_4.0x4.0mm | TP1, TP2 |
| 2 | Test Point | TestPoint:TestPoint_Pad_D1.5mm | TP3, TP4 |
| 1 | 0.5A Fuse | Fuse:Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 1 | 1.0uF 16V | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C31 |
| 1 | 1.5K Ohms | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R18 |
| 1 | 10 nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C14 |
| 1 | 100 Ohms | Potentiometer_THT:Potentiometer_Bourns_3386P_Vertical | R16 |
| 1 | 10K Ohms | Potentiometer_THT:Potentiometer_Bourns_3386P_Vertical | R13 |
| 1 | 10M Ohms | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9 |
| 1 | 120 Ohms | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R19 |
| 1 | 470pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C13 |
| 1 | 5.1 KOhms | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R37 |
| 1 | 50 Ohms | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R17 |
| 1 | Conn_01x02_Pin | Connector_JST:JST_EH_B2B-EH-A_1x02_P2.50mm_Vertical | J5 |
| 1 | LED Green | LED_THT:LED_D3.0mm | D4 |
| 1 | LED Red | LED_THT:LED_D3.0mm | D5 |
| 1 | LMH6611MK/NOPB | Package_TO_SOT_SMD:TSOT-23-6 | U2 |
| 1 | MAX1555EZK+T | Package_TO_SOT_SMD:TSOT-23-5 | U4 |
| 1 | SMBJ5.0A | Diode_SMD:D_SMB | D3 |
| 1 | TPS65133DPDR | PersonalFootprint_Library:WSON-12_L3.0-W3.0-P0.45-BL-EP | U5 |
| 1 | USB_C_Receptacle_PowerOnly_6P | Connector_USB:USB_C_Receptacle_GCT_USB4135-GF-A_6P_TopMnt_Horizontal | J4 |
Similar boards
- 2 layers

- 2 layers51 × 70 mm

Auto dimmer
ilyushkin/auto_dimmer
Automatic dimmer for IKEA NYMANE (103.569.62) lamp based on AVR ATtiny13A MCU.
56 parts2GPL-3.0 - 6 layers73 × 100 mm

- 4 layers28 × 98.2 mm

ESP32-PoE ISO Rev N1
OLIMEX/ESP32-POE-ISO
ESP32 Power Over Ethernet board with 3000VDC Galvanic insulation
146 parts145 - 4 layers77.1 × 63.8 mm

- 4 layers250.4 × 131 mm

Panel-16
geezacoleman/owl-driver-board
Development of a board that receives GPIO input and allows on/off control of connected solenoids.
939 parts14MIT - 2 layers98.9 × 78 mm

Siot gateway particle io
simpleiot/hardware
Hardware designs for IoT devices and sensor nodes.
28 parts9Apache-2.0 - 2 layers170 × 120 mm

Questions
How big is the Differential Probe PCB?
It measures 95 × 57 mm and has 2 copper layers, 2.63 mm thick.
What parts does the Differential Probe use?
97 parts, built around the ADA4817-1ARDZ-R7, MAX1555EZK+T, BAV99 and SMBJ5.0A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Differential Probe KiCad files?
From the ugo-silato/Differential-Probe repository on GitHub, at the commit this page was made from: the board is Differential Probe.kicad_pcb and its schematic Differential Probe.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Differential Probe design in my own project?
Its repository states no licence, so its author keeps all rights: ask ugo-silato before reusing the design.