

Pi top Glimmer
Accessory board for pi-topCEED and pi-top laptor
- Size
- 65 × 56 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 107
- Nets
- 87
- Pads
- 385
- Tracks, vias
- 1,481, 105
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20170123)
- Created
- 25 Jun 2017
- Updated
- 27 Jun 2017
Overview
Pi top Glimmer is an open-source printed circuit board by uChip, from the uChip/pi-top_Glimmer repository on GitHub. It is a 4-layer board of 65 × 56 mm with 107 parts on 87 nets, routed with 1,481 tracks and 105 vias.
It is built around the ATMEGA328P-AU, 74LV164D and AP7215-33YG, with the TSOP38238 and IRFML8244TR among its other parts. Its parts include 64 diodes, 10 capacitors, 8 transistors, 7 resistors and 6 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
5ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)74LV164D
SO-14SO-14 Shift Registers ROHSNexperiaShifting RegisterAP7215-33YG
SOT-89-3-40℃~+125℃@(Tj) 1 250mV@(100mA) 3.3V 5.5V 55dB@(1kHz) 600mA 80uA Fixed Over Current Protection、Enable、Short Circuit Protection Positive SOT-89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTSOP38238
SIP-3-2.54mm-25℃~+85℃ 10mW 2.5V~5.5V 350uA 38kHz 45m ±45° SIP-3-2.54mm Infrared Remote Receiver (IRM) ROHSVishay IntertechnologyInfrared Remote Receiver (IRM)IRFML8244TR
SOT23-325V 5.8A N-Channel HEXFET® Power MOSFETInfineon TechnologiesUncategorised
README
README.mdpi-top_Glimmer
NOTE: This project is a work in progress and is subject to change. See the Status section for recent changes.
This repository contains the design files and write-up for pi-top_Glimmer.
Note: I have no affiliation with pi-top other than being a customer.
The pi-top Glimmer is an accessory board for the pi-topCEED. It also fits the pi-top laptop. The board reconstitutes the Raspberry Pi GPIO connector. Unlike the pi-topPROTO the Glimmer places the connector optimally for connecting the "T-Cobbler Plus - GPIO Breakout" or the "Pi Wedge".
The board includes support for an IR Receiver (TSOP38238 or similar) for IR remote control of the pi-top. An on board ATmega328p (programmable Arduino style) monitors the Raw, 5V and 3.3V voltage levels of the pi-top power supply to help detect if the supply is overloaded.
The pi-top Glimmer passes the accessory buss through to the other end of the board so that the pi-topSPEAKER or other accessories can be plugged in. An effort has been made to use a minimum of Raspberry Pi GPIO resources so that as many HATs as possible will still work. The pi-top HUB board commits GPIO's 7, 9,10 & 11 as the SPI buss with HUB board select on GPIO 7 (CE1_N). To this the pi-top Glimmer adds the use of GPIOs 2 & 3 as the I2C buss (sharable with other boards) and resides at I2C address 110. The IR Receiver is optionally connected via solder jumper to GPIO 24 (pin 18).
Finally, the board includes an 8x8 LED (single color, on/off) array that is refreshed from the Arduino and commanded from the pi-top's Raspberry Pi.
The software folder contains a "sketch" that is source code for the Arduino which can be changed and updated from the pi-top.
The board is built using a combination of through-hole and (larger scale) surface mount technologies and is reasonably easy to hand assemble. I created this board for a number of reasons; to more easily enable prototyping on the pi-top, to learn more about the pi-top's accessory buss, to experiment with I2C on both RPi and Arduino, to teach myself KiCad, and to enable future projects I have in mind.
I did it as a one off, but it seems to have some utility for classroom scenarios. If there is interest I would be willing to make a manufacturing run of the pi-top Glimmer as a product.
Order PCBs
You can order this PCB directly from OSH Park. Click on the following link.
- pi-top Glimmer - https://oshpark.com/shared_projects/x6jgBiCp
See the Bill of Materials (BOM) file in the repo Hardware folder for a parts list.
Status
- PCB (rev 1.0beta) has been checked against components and specs and is currently out for fab.
File Formats
Hardware design files are in "KiCad EDA" .kicad_pcb and .sch formats (KiCAD version: (2017-05-14 revision 14bb238b3)). A free version of the software can be downloaded from kicad-pcb.org.
The example code is in Arduino .ino format (text). A free version of the Arduino software can be downloaded from www.arduino.cc.
Distribution License
License:

pi-top Glimmer by C.Schnarel is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Parts
107| Qty | Value | Footprint | References |
|---|---|---|---|
| 64 | RED | LEDs:LED_0805 | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +48 |
| 8 | 0.1uF | Capacitors_SMD:C_0805_HandSoldering | C2, C4, C5, C6, C7, C8, C9, C10 |
| 8 | IRFML8244 | TO_SOT_Packages_SMD:SOT-23_Handsoldering | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 |
| 2 | 10uF | Capacitors_SMD:C_0805_HandSoldering | C1, C3 |
| 2 | 74LV164 | Housings_SSOP:TSSOP-14_4.4x5mm_Pitch0.65mm | U3, U4 |
| 1 | 10k | Resistors_SMD:R_0805_HandSoldering | R1 |
| 1 | 2.2k | Resistors_SMD:R_0805_HandSoldering | R7 |
| 1 | 2.2uH | Inductors_SMD:L_0805_HandSoldering | L1 |
| 1 | 3.3k | Resistors_SMD:R_0805_HandSoldering | R8 |
| 1 | 300R | Resistors_SMD:R_0805_HandSoldering | R5 |
| 1 | 3k | Resistors_SMD:R_0805_HandSoldering | R6 |
| 1 | 4.48k | Resistors_SMD:R_0805_HandSoldering | R3 |
| 1 | 715R | Resistors_SMD:R_0805_HandSoldering | R4 |
| 1 | 8MHz | pi-top:Resonator_SMD_muRata_CSTCE_3.2mm_1.3mm | Y1 |
| 1 | AP7215-33YG | TO_SOT_Packages_SMD:SOT-89-3_Handsoldering | U1 |
| 1 | ATMEGA328P-AU | Housings_QFP:TQFP-32_7x7mm_Pitch0.8mm | U2 |
| 1 | CONN_01X06 | Pin_Headers:Pin_Header_Straight_1x06_Pitch2.54mm | J1 |
| 1 | CONN_02X03 | Pin_Headers:Pin_Header_Straight_2x03_Pitch2.54mm | J2 |
| 1 | CONN_02X17 | Pin_Headers:Pin_Header_Angled_2x17_Pitch2.00mm | J3 |
| 1 | CONN_02X17 | Socket_Strips:Socket_Strip_Angled_2x17_Pitch2.00mm | J5 |
| 1 | CONN_02X20 | Pin_Headers:Pin_Header_Straight_2x20_Pitch2.54mm | J4 |
| 1 | LOGO | MyLogos:S_Silk | G*** |
| 1 | SPST_Jumper | SolderJumpers:SPST_Jumper | J6 |
| 1 | TSOP38238 | Opto-Devices:IRReceiver_Vishay_MINICAST-3pin | U5 |
The 103 most common of 107 parts.
Similar boards
- 2 layers121 × 70.5 mm

- 2 layers75.1 × 85.2 mm

- 2 layers74 × 72 mm

- 2 layers50 × 74 mm

- 2 layers83 × 100 mm

- 2 layers58 × 84 mm

- 2 layers19.6 × 24.1 mm

Moleblink
rjhsun/moleblink
ATtiny85-based illuminated PCB keychain featuring the Blacker House crest
31 parts2CC-BY-SA-4.0 - 2 layers155 × 140 mm

Control board
Sergio5714/experimental-teg-testbed-firmware
Firmware for STM32 MCU of testbed data acquisition and control system
89 parts2
Questions
How big is the Pi top Glimmer PCB?
It measures 65 × 56 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Pi top Glimmer use?
107 parts, built around the ATMEGA328P-AU, 74LV164D, AP7215-33YG and TSOP38238. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pi top Glimmer KiCad files?
From the uChip/pi-top_Glimmer repository on GitHub, at the commit this page was made from: the board is pi-top_Glimmer.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pi top Glimmer design in my own project?
Its repository states no licence, so its author keeps all rights: ask uChip before reusing the design.