

DSH AEGIS
a physical password manager, kinda like a mix between a yubikey and macropad (NOTE: ill probably remodel the case & remake the pcb to use a actual micro sd card port instead of a hole to plug in a premade sd/micro sd slot.)
- Size
- 69.5 × 98.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 15
- Nets
- 43
- Pads
- 136
- Tracks, vias
- 217, 21
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 13 Jul 2026
- Updated
- 2 Oct 2026
Overview
DSH AEGIS is an open-source printed circuit board by TwinSailsStudios, from the TwinSailsStudios/DSH-AEGIS repository on GitHub, published under the MIT licence. It is a 2-layer board of 69.5 × 98.5 mm with 15 parts on 43 nets, routed with 217 tracks and 21 vias.
It is built around the ESP32-S3-WROOM-1-N8 and AMS1117-3.3. Its parts include 6 switches, 3 ICs, 2 capacitors, 2 resistors and 2 connectors. It belongs with the keyboards and input boards and the ESP32 boards of this library.
Main components
2ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdDSH-AEGIS
https://github.com/user-attachments/assets/2e60c4a9-2eaf-4800-a794-9d0f289f58ca Video of 3d model
UPDATE NOTICE:
alr so i added step/stp files in the hardware folder in a zip file since they were too big for regular uploads (terminal limit is 100mb), i also made the pcb more compact, but the i didnt update the cover image, so you'll have to download the pcb file.
A physical password manager. ESP32-S3, a tiny OLED, six buttons, and an SD card. Plugs into your computer over USB-C and types your passwords for you.
Status: designed, not built. The schematic and PCB are done, the firmware is written. I haven't ordered the board yet because I'm paying for this stuff myself and PCBs cost money. Everything here is verified in KiCad, not on a bench. I'll update this when I can afford to fab it.
why
I was using the same password on like nine different sites. Which is bad. Every password manager I looked at wanted me to trust a company with all of it, and I didn't love that either. So: keep them on an SD card, in my pocket, encrypted.
what it does
- Locks behind a PIN you enter on the buttons
- Vault is encrypted on the SD card with AES-256
- Types the password straight into the login box over USB
- Can do username → Tab → password to fill a whole form
- Generates strong random passwords
- Auto-locks after 60s if you walk away
The typing thing is the whole point. The ESP32-S3 has native USB, so the board doesn't pretend to be a keyboard — your computer genuinely thinks a keyboard got plugged in. No drivers, no app. Works on any machine you walk up to.
hardware
| part | what it does |
|---|---|
| ESP32-S3-WROOM-1 | the brain. picked for native USB |
| SSD1306 128x32 OLED | the screen (I2C) |
| 6x tactile switches | the controls |
| microSD module | where the vault lives (SPI) |
| USB-C receptacle | power + keyboard |
| AMS1117-3.3 | 5V → 3.3V |
| 2x 5.1K resistors | CC pins, so USB-C actually gives you power |
pinout
| pin | goes to |
|---|---|
| IO0–IO5 | RECORD, SAVE, PLAY, SCROLL-L, SELECT, SCROLL-R |
| IO6 / IO7 | OLED SCL / SDA |
| IO35–IO38 | SD CS / MOSI / SCK / MISO |
Heads up on IO35–37. On an ESP32-S3 module with octal (R8) PSRAM, those three pins are wired to the PSRAM die internally and you can't use them as GPIO. This board only works with a no-PSRAM or quad-PSRAM module. If you build it, check the part number, and set PSRAM: Disabled in the Arduino IDE — leave it on OPI and the chip claims those pins at boot, before your code runs, and the SD card silently never mounts.
how you'd use it
Enter your PIN. Scroll to the login you want with the arrow buttons. Click into whatever password box you're filling out on your computer. Hit PLAY. Done.
SELECT opens a menu with more options: type just the password, type username+Tab+password, show the password on screen, or delete it.
Adding a new entry is the weak spot right now — you press RECORD and it hands
off to the serial monitor, where you send label⇥username⇥password. A password
manager that needs a computer to set up is a bit embarrassing and I want to fix
it. (Put * as the password and it generates one for you.)
Then hit SAVE to encrypt it and write it to the card.
the crypto
Boring on purpose. Your PIN goes through PBKDF2-HMAC-SHA256 (60,000 rounds, random salt) to turn 4 digits into a real key. Vault is AES-256-CBC. There's an HMAC over the ciphertext, so a wrong PIN fails the check and the device never even attempts to decrypt. Salt and IV are fresh every save.
I did not invent any of this. Inventing your own crypto is how you become a cautionary example in someone's blog post.
build it yourself
Firmware is in firmware/. You need the U8g2 library; everything else ships
with the ESP32 Arduino core.
Board settings:
- Board: ESP32S3 Dev Module
- USB CDC On Boot: Enabled
- USB Mode: USB-OTG (TinyUSB)
- PSRAM: Disabled (see the IO35 warning above)
KiCad project is in hardware/.
what's not done
- Never physically built. Simulated and verified in KiCad only.
- A 4-digit PIN is 10,000 combinations. The PBKDF2 rounds slow an attacker down a lot but it's not amazing if someone steals the card and is patient.
- No lockout after repeated wrong guesses.
- Can't add entries on the device, needs serial.
- No way to change your PIN without wiping everything.
- Case is modelled in Tinkercad but not printed.
AI use
I used gemini to help with some kicad features and trying to debug a probelm with exporting my 3d model of my pcb I used Claude to help write the firmware and to talk through design decisions (pin conflicts, how to structure the vault encryption). The schematic, PCB layout, 3D model, and this README are mine. the firmware, im not gonna act like i wrote it from scratch, it was more like using claude to frankenstien my code togetehr into a working firmware, since i haventbuilt ts irl yet, if any of yall try PLEASE lmk if theres any code problems, thx:)
EDIT: I also gave claude access to organize all the files
license
MIT. do whatever.
Parts
15| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | SW_Push | Button_Switch_Keyboard:SW_Cherry_MX_1.00u_PCB | SW1, SW2, SW3, SW4, SW5, SW6 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 2 | 5.1K | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | Conn_01x06_Socket | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J1 |
| 1 | ER_OLEDM0.91_1x-I2C | Display:ER_OLEDM0.91_1x-I2C | U2 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U1 |
| 1 | USB_C_Receptacle | Connector_USB:USB_C_Receptacle_XKB_U262-16XN-4BVC11 | J2 |
Similar boards
- 2 layers86 × 54 mm

- 2 layers55 × 100 mm

- 2 layers110 × 100 mm

PidginTranslator
DevMubarak1/PidginTranslator
Handheld translator for Nigerian languages. No internet needed for common phrases, YarnGPT for everything else.
14 parts21MIT - 4 layers58.5 × 85.5 mm

- 2 layers50.6 × 71.1 mm

Open ESPilot
Tomas-Kuchta-FPV/Open-ESPilot
An open-source project to develop a custom ESP32-based flight controller designed primarily for use with ArduPilot. Focused on affordability, flexibility, and ease of integration with various robotic and UAV platforms.
109 parts18CERN-OHL-W-2.0 - 4 layers102 × 100 mm

Zelvicka
RoboticsBrno/Robutek
Robůtek je robotická platforma založená na čipu ESP32-S3. Je velice rozšitiřelný, ale ze základu umí jezdit, kreslit fixou, jezdit po čáře, pohybovat se bludištěm. Programování je přes Jaculus.
214 parts12 - 2 layers156 × 66 mm

Dash 6.8
romioRN/Dash6.8-hardware
wifi name "service", password 12345678, connect to 192.167.4.1
152 parts11Apache-2.0 - 4 layers100 × 100 mm

Questions
How big is the DSH AEGIS PCB?
It measures 69.5 × 98.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the DSH AEGIS use?
15 parts, built around the ESP32-S3-WROOM-1-N8 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DSH AEGIS KiCad files?
From the TwinSailsStudios/DSH-AEGIS repository on GitHub, at the commit this page was made from: the board is hardware/pcb/DSH-AEGIS.kicad_pcb and its schematic hardware/pcb/DSH-AEGIS.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the DSH AEGIS design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).