

Sr jv esp32
SR-JV80 Programmable Expansion Card with ESP32 Wi-Fi
- Size
- 58.5 × 85.5 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 84
- Nets
- 135
- Pads
- 508
- Tracks, vias
- 2,495, 356
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 23 Feb 2025
- Updated
- 27 May 2025
Overview
Sr jv esp32 is an open-source printed circuit board by connorzheng97, from the connorzheng97/srjv repository on GitHub. It is a 4-layer board of 58.5 × 85.5 mm with 84 parts on 135 nets, routed with 2,495 tracks and 356 vias.
It is built around the SN74LVC1G125DBV, ESP32-S3-WROOM-1-N8 and SN74LVC8T245PW, with the SN74AHC595D, 74AHC86D and AMS1117-3.3 among its other parts. Its parts include 29 capacitors, 27 resistors, 16 ICs, 4 connectors and 3 diodes. It belongs with the radio and wireless boards and the ESP32 boards of this library.
Main components
9SN74LVC1G125DBV
SOT-23-5-40℃~+125℃ 1 1 1.65V~5.5V 10uA 3.7ns@3.3V,15pF 32mA 32mA 74LVC Tri-State Unidirectional SOT-23-5 Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsSpecialty LogicESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesSN74LVC8T245PW
TSSOP-24-40℃~+85℃ 1 1.65V~5.5V 1.65V~5.5V 8 Bidirectional CMOS CMOS Tri-State TSSOP-24 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level ShiftersSN74AHC595D
SOIC-16-40℃~+125℃ 1 10.5ns@5V,50pF 170MHz 2V~5.5V 74AHC 8 8mA Asynchronous clear function、Output enable Serial-to-Serial or Parallel Tri-State SOIC-16 Shift Registers ROHSTexas InstrumentsShift Registers74AHC86D
SOP-14-40℃~+125℃ 1.5V、2.1V、3.85V 11ns@5V,50pF 2 2.9V、4.4V 2V~5.5V 40uA 500mV、900mV、1.65V 550mV 74AHC Overvoltage-tolerant input XOR Gate SOP-14 Logic Gates ROHSNexperiaGatesAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators100UF 10V 4*7
插件,4x7mm1.5mm 1000hrs@105℃ 100uF 10V 4mm 7mm 插件,4x7mm Aluminum Electrolytic Capacitors - Leaded ROHSLCSCAluminum Electrolytic Capacitors - Leaded1N4148W
SOD-123150mA 1A 1V@50mA 1uA@75V 400mW 4ns 75V Independent SOD-123 Switching Diodes ROHSSTMicroelectronicsSwitching DiodesTS-1187A-B-A-B
SMD-4P,5.1x5.1mm-30℃~+85℃ 1.5mm 1.6N 100,000 cycles 12V 5.1mm 5.1mm 50mA Gold No Round Button SPST Surface Mount,Vertical Without Bracket SMD-4P,5.1x5.1mm Tactile Switches ROHSXKB ConnectionTactile Switches
README
README.mdsrjv
SR-JV80 Programmable Expansion Card with ESP32 Wi-Fi
- Product info page at https://www.ddzheng.cc/?page_id=666
- Blog post at https://www.ddzheng.cc/?p=617
This board is a re-writable ROM card with a Wi-Fi based user interface. It can store a ROM image up to 8MB/64Mbit, usually custom authored, and be used in compatible Roland synthesizers in place of an original SR-JV80 series expansion card to research the sound generation and synthesizing.

Hardware Info
- ESP32-S3 Wroom module requires at least 2 MB Flash (No OTA) or 4 MB (with OTA).
- The NOR flash can be TSSOP 48 or 56 pin, 8 MB or more, 70ns or faster, with byte (8-bit) mode support. Regularly used for production is MX29LV640
- Connector is 40 pin SCSI all plastic connector or similar. The original card use MOLEX 52326-0401
- Reverse taped LED is only required for SMT production. For hand assembling regular 1206 LED can be used.
Fabricating
4-layer board. Can also be made with 2 layers without modification. Assemble as indicated (DNP = do not populate) in schematic.
Licsensing
Copyright Connor Zheng 2025.
This source describes Open Hardware and is licensed under the CERN-OHLW v2 or later. You may redistribute and modify this documentation and make products using it under the terms of the CERN-OHL-W v2 https:/cern.ch/cern-ohl. This documentation is distributed WITHOUT ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING OF MERCHANTABILITY, SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE. Please see the CERN-OHL-W v2 for applicable conditions.
Source location: https://github.com/connorzheng97/srjv
As per CERN-OHL-W v2 section 4.1, should You produce hardware based on these sources, You must maintain the Source Location visible on the external case and PCB top layer silkscreen of the SRJV or other product you make using this documentation.
Parts
84| Qty | Value | Footprint | References |
|---|---|---|---|
| 21 | 100n | Capacitor_SMD:C_0603_1608Metric | C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23, C25, C26 +5 |
| 15 | 10K | Resistor_SMD:R_0603_1608Metric | R3, R7, R8, R9, R10, R11, R12, R13, R14, R16, R17, R18, R20, R26, R27 |
| 4 | 10u | Capacitor_SMD:C_0603_1608Metric | C2, C5, C8, C24 |
| 4 | 5.1K | Resistor_SMD:R_0603_1608Metric | R2, R5, R22, R23 |
| 4 | SN74LVC1G125DBV | Package_TO_SOT_SMD:SOT-23-5 | U5, U14, U15, U16 |
| 4 | SN74LVC8T245 | Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm | U6, U7, U8, U9 |
| 3 | DNP | Resistor_SMD:R_0603_1608Metric | R1, R15, R19 |
| 3 | SN74AHC595 | Package_SO:TSSOP-16_4.4x5mm_P0.65mm | U10, U11, U12 |
| 2 | 100uF/10v | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C1, C6 |
| 2 | 1K | Resistor_SMD:R_0603_1608Metric | R4, R6 |
| 1 | 0R | Resistor_SMD:R_0603_1608Metric | R21 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R24 |
| 1 | 1N4148W | Diode_SMD:D_SOD-123 | D3 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C27 |
| 1 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | 74AHC86 | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U4 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | Conn_01x02 | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | Conn_40_SRJV_MountingPin | sr-jv-esp32:CONN_40P_SCSI_THT_Vertical | J1 |
| 1 | DNP | Capacitor_SMD:C_0603_1608Metric | C28 |
| 1 | DNP/0R | Resistor_SMD:R_0603_1608Metric | R25 |
| 1 | DNP/MAX809S | Package_TO_SOT_SMD:SOT-23 | U2 |
| 1 | ESP32-S3-WROOM-1 | sr-jv-esp32:ESP32-S3-WROOM-1 | U3 |
| 1 | ICE BLUE | new:LED_1206_3216Metric_ReverseMount | D2 |
| 1 | LOGO | Symbol:WEEE-Logo_5.6x8mm_SilkScreen | N3 |
| 1 | LOGO | Symbol:ESD-Logo_6.6x6mm_SilkScreen | N2 |
| 1 | LOGO | Symbol:OSHW-Logo_5.7x6mm_SilkScreen | N1 |
| 1 | NOR_FLASH_29064 | sr-jv-esp32:TSOP-I-56_48_18.4x14mm_P0.5mm | U13 |
| 1 | ORANGE | new:LED_1206_3216Metric_ReverseMount | D1 |
| 1 | TS-1187A | sr-jv-esp32:SW_Push_1P1T_XKB_TS-1187A_LONGPAD | SW1 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J2 |
Similar boards
- 4 layers94 × 65.9 mm

- 2 layers

- 2 layers88 × 130 mm

Windowmaster controller v2
Simplycissmus/windowmaster-s3-controller
Open hardware and ESP32-S3 firmware for a local 24 V window actuator controller with MQTT and Home Assistant integration.
68 parts1 - 4 layers70 × 70 mm

- 2 layers352.5 × 136.4 mm

Anson's Keyboard PCB
YeetTheAnson/AnsonKeyboard
When in custom color configuration mode, the display shows prompts for entering RGB values.
373 parts4 - 2 layers76.9 × 55 mm

AurisenseV2
catrahedron/AurisenseV2
A simple shift register based headpat haptics driver board for VRChat with 40 motor driver outputs and two SPI/UART extension ports
211 parts1CERN-OHL-W-2.0 - 2 layers92.4 × 40.6 mm

PrintBridge
Kingdragoncat/PrintBridge
Im so done with needing to unplug all my cords and plug it all in ontip of a file of boxes to print one god damn thing so i made my wired printer wireless
22 parts - 2 layers78 × 58 mm

Questions
How big is the Sr jv esp32 PCB?
It measures 58.5 × 85.5 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Sr jv esp32 use?
84 parts, built around the SN74LVC1G125DBV, ESP32-S3-WROOM-1-N8, SN74LVC8T245PW and SN74AHC595D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Sr jv esp32 KiCad files?
From the connorzheng97/srjv repository on GitHub, at the commit this page was made from: the board is sr-jv-esp32.kicad_pcb and its schematic sr-jv-esp32.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Sr jv esp32 design in my own project?
Its repository states no licence, so its author keeps all rights: ask connorzheng97 before reusing the design.