

Open ESPilot
An open-source project to develop a custom ESP32-based flight controller designed primarily for use with ArduPilot. Focused on affordability, flexibility, and ease of integration with various robotic and UAV platforms.
- Size
- 50.6 × 71.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 109
- Nets
- 90
- Pads
- 362
- Tracks, vias
- 538, 94
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 20 Jun 2025
- Updated
- 13 May 2026
Overview
Open ESPilot is an open-source printed circuit board by Tomas-Kuchta-FPV, from the Tomas-Kuchta-FPV/Open-ESPilot repository on GitHub, published under the CERN-OHL-W-2.0 licence. It is a 2-layer board of 50.6 × 71.1 mm with 109 parts on 90 nets, routed with 538 tracks and 94 vias.
It is built around the ESP32-S3-WROOM-1-N8, AMS1117-3.3 and BC847, with the PDZVTR5.1B, AO3401A and B5819W among its other parts. Its parts include 23 capacitors, 17 resistors, 13 connectors, 6 diodes and 5 ICs. It belongs with the robots and motor control boards and the ESP32 boards of this library.
Main components
9ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBC847
SOT-231 NPN 100MHz 100mA 100nA 110 200mW 45V 500mV 6V NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)PDZVTR5.1B
SOD-1281 Independent 1W 20uA@1V 5.1V 5.1V~5.7V 8Ω SOD-128 Zener Diodes ROHSROHM SemiconductorZener DiodesAO3401A
SOT-231 P-Channel 14nC@10V 30V 47mΩ@10V、60mΩ@4.5V、85mΩ@2.5V 4A 55pF 645pF 80pF 900mV SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsB5819W
SOD-123-55℃~+125℃ 1.5A 1mA@40V 25A 40V 600mV@1A Standalone SOD-123 Schottky Diodes ROHSMDDSchottky DiodesSSA34
SMA(DO-214AC)Schottky DiodesFUXINSEMITMB12A05
插件,D=12mmBuzzersJiangsu Huaneng ElecWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
README.mdOpen-ESPilot
This is a community-driven hardware project focused on creating an open and accessible Flight Controller (FC).
The main focus is on being low-cost, availability, hackability and openness!
That's why I've started this project to make an open-source and low-cost FC with the community.
The target firmware is ArduPilot, which is a powerful open-source autopilot system.
Core Design Ideas
- Dev board meets flight controller hybrid
- Keep it budget-friendly
- Readily available components
- Hackability so you can hack on your features
- ❤️ Designed with care by and for the community
What are the goals
The main one is a reference platform for devs and hackers. Then we can move to a product for the wider public.
With the focus being on Hackability and Openness, there are endless possibilities for creativity!
Here are a few ideas:
- Prototyping and experimentation
- A low-cost alternative for those priced out of commercial FCs
- Teaching control theory and autonomous systems in schools
Why did I make it
I have a lot of experience with FPV drones running Betaflight.
Then I started playing with the ESP32-based ArduPilot for almost three years. All of them were for a competition called Robotem Rovne.
- The first one is an autonomous rover which was breadboarded together. As with any other breadboard project, the wires were loose, they didn't make contact, and they were falling off.
- Then I made a second rover with an FC soldered on a proto board. Which worked wonderfully!
- Then I tried to make a PCB with a brushed motor controller. Not going to talk about this one. Didn't go as planned. :(
- After that, I've bought a SpeedyBee f405 WING FC and mounted it to an RC car. This is my Ardupilot learning platform.
And now we are here. ...
That was when I had the idea of making an ESP32 Flight Controller.
Future development
This is the first FC I made with the help of the community, so huge thanks to everyone. ♥️
Ideas for future
- modular system (eg, ELRS, GPS modules)
- 30x30 FC for FPV drones. That's harder as there are plenty of great cheap FCs
Project Status
I have the PCB made, and now I need to order everything and test it!
| PCB | Render | Finished PCB |
|---|---|---|
![]() | ![]() | ![]() |
The Plan
- Basic schematic and PCB layout
- Selection of components is decided in Issues
- Compare BOM cost to commercial FCs - going to figure it out when I have time.
- Complete code, documentation, and build guide
Design Phases
- Planning & goal setting✅
- Schematic design✅
- Start with core ESP32 + power
- Add sensors and outputs
- Evaluate BOM & gather feedback
- Community feedback loop✅
- PCB layout✅
- Prototype ordering
- …And hopefully it works on the first try! 🤞
Firmware
We are now focusing on ArduPilot ESP32 port. They are making incredible work, and the project wouldn't exist without their hard work.
I won't be able to write the code by myself, so huge props to the contributors! That's why I'm focusing on the HW.
There are also possibilities for you to write your own code.
Contributing
We would love to hear feedback. We are open to everything, including issues, ideas and suggestions.
That's why this project is Open Source.
BOM
Built With
- ESP32 – the core MCU
- KiCad – for PCB design
- ArduPilot – the autopilot software we're building for
- ❤️ Open source tools and community support
- ... and Love ❤️
License
Hardware: CERN-OHL-W
Firmware: Ardupilot
Thanks
Many thanks to the amazing people who make Hack Club possible.
Thanks to Hack Club for inspiring so many people. I don't know the numbers, but maybe around thousands.
Most of them are probably going to get a career from it. Love your work! ❤️
And big thanks to the ArduPilot community for keeping robotics and autonomy Open and hackable.
Parts
109| Qty | Value | Footprint | References |
|---|---|---|---|
| 23 | R_Small | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_RoundedPad1.0x1.5mm | GJ2, GJ4, GJ14, GJ15, GJ16, GJ17, GJ18, GJ21, GJ35, GJ36, GJ37, GJ38, GJ39, GJ40, GJ41, GJ42 +7 |
| 14 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3, C12, C13, C14, C15, C17, C18, C19, C20, C21, C22, C23, C24 |
| 7 | 22uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C4, C6, C7, C8, C9, C16 |
| 5 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R10, R11, R12, R13 |
| 4 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R14, R15, R16, R17 |
| 2 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R4 |
| 2 | 10R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7, R9 |
| 2 | 5k1 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 2 | BC847 | Package_TO_SOT_SMD:SOT-23 | Q2, Q3 |
| 2 | PDZVTR5.1B | Diode_SMD:D_SOD-128 | D2, D3 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW1, SW2 |
| 1 | 0.5mR | Resistor_SMD:R_2512_6332Metric_Pad1.40x3.35mm_HandSolder | R8 |
| 1 | 1000uF | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C5 |
| 1 | 1000uF | Capacitor_SMD:CP_Elec_8x10 | C10 |
| 1 | 3V3 IG | Diode_SMD:D_SOD-128 | D6 |
| 1 | 5V/Vx | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_RoundedPad1.0x1.5mm | JP4 |
| 1 | 91k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5 |
| 1 | A0 | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_RoundedPad1.0x1.5mm | JP1 |
| 1 | A1 | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_RoundedPad1.0x1.5mm | JP2 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-89-3 | U2 |
| 1 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | B5819W | Diode_SMD:D_SOD-123 | D4 |
| 1 | Clone "MP1584" module | Clone _MP1584_ module:Clone _MP1584_ module | M1 |
| 1 | ESP32-S3-WROOM-1-N8 | RF_Module:ESP32-S3-WROOM-1 | U1 |
| 1 | FerriteBead | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | FB1 |
| 1 | GND | Power Pads:PP_03x | J4 |
| 1 | GND | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J8 |
| 1 | GPIO1 | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP4 |
| 1 | GPIO3 | TestPoint:TestPoint_Pad_D2.0mm | TP1 |
| 1 | GPIO45 | TestPoint:TestPoint_Pad_D2.0mm | TP2 |
| 1 | GPIO46 | TestPoint:TestPoint_Pad_D2.0mm | TP3 |
| 1 | GPIO5 | TestPoint:TestPoint_Pad_D2.0mm | TP5 |
| 1 | GY91 | GY-91:GY-91 | M2 |
| 1 | I2C | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J12 |
| 1 | INA219AxD | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | LED out | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J14 |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Hirose_DM3AT-SF-PEJM5 | U5 |
| 1 | PWM output | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J5 |
| 1 | RC in | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | RCin - Inv/Non-Inv | Jumper:SolderJumper-3_P1.3mm_Bridged2Bar12_RoundedPad1.0x1.5mm_NumberLabels | JP5 |
| 1 | REG/USB | Jumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm | JP6 |
| 1 | SD-DAT1 | TestPoint:TestPoint_Pad_D2.0mm | TP6 |
| 1 | SD-DAT2 | TestPoint:TestPoint_Pad_D2.0mm | TP7 |
| 1 | SD-DAT3 | TestPoint:TestPoint_Pad_D2.0mm | TP8 |
| 1 | SSA34 | Diode_SMD:D_SMA | D1 |
| 1 | TMB12A05 | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | UART0 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J9 |
| 1 | UART1 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J10 |
| 1 | UART2 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J11 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB-C:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | VIN | Power Pads:PP_02x | J3 |
| 1 | VOUT | Power Pads:PP_02x | J2 |
| 1 | Vx | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J7 |
| 1 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D5 |
Similar boards
- 4 layers128.1 × 128.1 mm

- 2 layers160 × 110 mm

Acquedotto test v4 finale
igorilla666/water-controller
Scheda di controllo basata sul modulo Waveshare ESP32-S3-ETH, con ingressi sensore, RS-485, pilotaggio rele, buzzer e alimentazione/protezioni dedicate.
139 parts1CERN-OHL-S-2.0 - 2 layers60 × 70 mm

MC60
wyolum/MC60
break out board for Quectel MC60 Ultra-small LCC Quad-band GSM/GPRS/GNSS Module
109 parts17 - 2 layers88.3 × 106.8 mm

- 2 layers200 × 70 mm

FRL RFiD Box
FREILab/easyVerwaltungHardware
Hardware und Firmware für alle Geräte im Bezug zu easyVerwaltung
65 parts2 - 2 layers54 × 85 mm

Guardian Sense
ficosta/Guardian-Sense
Guardian-Sense is a versatile hardware project based on the ESP32-S3, designed to monitor environmental conditions and provide real-time data to Zabbix.
38 parts - 2 layers67 × 96 mm

- 2 layers141.6 × 70 mm

Questions
How big is the Open ESPilot PCB?
It measures 50.6 × 71.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Open ESPilot use?
109 parts, built around the ESP32-S3-WROOM-1-N8, AMS1117-3.3, BC847 and PDZVTR5.1B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Open ESPilot KiCad files?
From the Tomas-Kuchta-FPV/Open-ESPilot repository on GitHub, at the commit this page was made from: the board is PCB/Open-ESPilot/Open-ESPilot.kicad_pcb and its schematic PCB/Open-ESPilot/Open-ESPilot-MCU.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Open ESPilot design in my own project?
Its repository publishes it under the CERN-OHL-W-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).


