

AquaMQTT
Monitor and control your Groupe Atlantic (Explorer, Calypso, Aquawin,...) heat pump using MQTT
- Size
- 45 × 65 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 16
- Nets
- 41
- Pads
- 84
- Tracks, vias
- 161, 2
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 8 Sep 2023
- Updated
- 3 May 2026
Overview
AquaMQTT is an open-source printed circuit board by tspopp, from the tspopp/AquaMQTT repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 45 × 65 mm with 16 parts on 41 nets, routed with 161 tracks and 2 vias.
It is built around the SN74LVC2T45DCURE4. Its parts include 8 connectors, 2 resistors and 2 ICs. It belongs with the home automation and IoT boards and the ESP32 boards of this library.
Main components
1README
pcb/README.mdAquaMqtt PCB Board
The AquaMQTT PCB Board is intended to be installed between the communication wires of the DHW HMI Controller and the DHW Mainboard. To enable the communication to both HMI Controller and DHW Mainboard, the board provides two individual USART entities in One-Wire Mode. The Arduino ESP32 on the board runs AquaMQTT, providing communication via WiFi/MQTT while being powerful enough to handle any time critical USART communication with the heat pumps hmi controller and main board.
The boards are designed using Kicad. If you want to edit the layout, you may need to install an additional Arduino Kicad library before opening/editing the project.
Changelog
| Version | Description |
|---|---|
| 2.0 | RAST Sockets, SMD SN74LVC2T45, Pre-assembly Ready |
| 1.0 | Initial Design, Self-Soldering |
Revision 2.0
Note: Revision 2.0 needs AquaMQTT v1.7.0 or later for MITM mode
This revision fixes an issue, where certain heatpumps were not able to communicate due to a very sensitive serial link and changes of impedance. The Logic-Level-Converter and the one-wire USART circuit have been replaced by two SN74LVC2T45. Thanks to @Arrnooo for debugging, verifying and providing a new design proposal.
Additionally, this revision adds optional RAST sockets. Thanks to @tukutt for providing the design and custom adapters, originally used with revision 1.0 of the AquaMQTT board (see below).
Buy Pre-Assembled
This board uses tiny SMD SSOP parts (SN74LVC2T45) so self-soldering is most probably an issue. This revision is meant to be bought pre-assembled from JLCPCB
- Upload
AquaMQTT_Board_Revision_v2.zipas gerber file - Enable "PCB Assembly"
- Proceed and upload
AquaMQTT_Board_Revision_v2_BOM.csvas BOM - Proceed and upload
AquaMQTT_Board_Revision_v2_CPL.csvas CPL - Verify matched parts (should be good out of the box)
- Verify component placement (should be good out of the box)
If there are any issues during production, you may reference a successful previous order.
Parts
| Item | Count | Estimated Cost |
|---|---|---|
| Pre-Soldered AquaMQTT Board (Revision 2.0) (https://jlcpcb.com/) | 1x | ~ 6 $ |
| Arduino Nano ESP32 with Headers (ABX00083). Note: Community suggested cheaper alternative | 1x | ~ 5-20 € |
Revision 1.0
First revision, which is still good to use. There is no need to replace it with revision 2.0 in case it works for your heatpump.
An optional DS3231 Real Time Clock might be added to the board. This might be handy in case AquaMQTT will be ever used without any HMI at all. It would ensure a recovery with correct date and time after power outage and without WiFi. Adding a RTC Module is experimental and untested!
RAST vs. 2x4 Connector
Your heat pump may use a different connector such as the Thermor Aeromax 5. Happily @tukutt designed an adapter pcb to connect those heatpumps without cutting any cables. Read more about this in #51.
BOM
| Item | Count | Estimated Cost |
|---|---|---|
| AquaMqtt PCB Board (e.g. via AISLER.net) | 1x | ~ 7 € |
| Arduino Nano ESP32. Note: Community suggested cheaper alternative | 1x | ~ 20 € |
| Cable 2x4 2,54mm (Socket-Housing, Contacts, Wiring, Dupont | 1x | ~ 10 € |
| Real Time Clock RTC DS3231 (optional, experimental) | (1x) | ~ 6 € |
| SparkFun Logic Level Converter - 3.3V to 5V Bi-Directional or similar | 1x | ~ 4 € |
| 100k Resistance 0207 (Ø x L) 2.5 mm x 6.8 mm | 3x | < 1 € |
| 10k Resistance 0207 (Ø x L) 2.5 mm x 6.8 mm | 3x | < 1 € |
| 4.7k Resistance 0207 (Ø x L) 2.5 mm x 6.8 mm | 3x | < 1 € |
| Transistor BC547A TO-92 | 4x | < 1 € |
| Pin Header 2x4 2,54mm | 2x | < 1 € |
| Pin Header 1x4 2,54mm | 2x | < 1 € |
| Pin Header 1x2 2,54mm | 1x | < 1 € |
Parts
16| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole | MountingHole:MountingHole_4.3mm_M4_DIN965 | H1, H2, H3, H4 |
| 2 | R10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2 |
| 2 | SN74LVC2T45DCUR | Package_SO:SSOP-8_2.95x2.8mm_P0.65mm | U1, U2 |
| 1 | DHW HMI | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J7 |
| 1 | DHW MAIN | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J3 |
| 1 | Nano L | Connector_PinSocket_2.54mm:PinSocket_1x15_P2.54mm_Vertical | J5 |
| 1 | Nano R | Connector_PinSocket_2.54mm:PinSocket_1x15_P2.54mm_Vertical | J6 |
| 1 | Passthrough | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | RAST HMI | rast:RAST_3517-06_(2.5MM)_2 COPY | J4 |
| 1 | RAST MAIN | rast:RAST_3517-06_(2.5MM)_2 COPY | J2 |
| 1 | Serial | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
Similar boards
- 6 layers190 × 140 mm

- 4 layers48.5 × 33.5 mm

- 2 layers220 × 300 mm

Transit
thebenedict/seattletransit-hardware
Schematic and PCB for a circuit board map of Seattle area public transit.
448 parts14CERN-OHL-W-2.0 - 4 layers82.7 × 77.8 mm

GlowCorePanel
LEDs-by-glowingkitty/GlowCore
The easiest way to control your DIY LED project.
472 parts6GPL-3.0 - 4 layers30 × 40 mm

GlowCoreMini PCB
LEDs-by-glowingkitty/GlowCore-Mini
A small PCB for controlling an LED strip via USB-C or DC power. WLED compatible and with an integrated microphone for sound reactive animations!
89 parts6GPL-3.0 - 2 layers27.9 × 34.3 mm

GlowBand PCB
LEDs-by-glowingkitty/GlowBand
GlowBand is an exciting LED wristband. For dancing at parties and festivals, for long-time exposure photography, and for everyday situations that need some light.
76 parts4MIT - 4 layers80 × 100 mm

Ice40 breakout
RubenVoell/iceduino
The basic idea behind this project is to create a simple breakout of an ICE40 FPGA with some LEDs and Buttons to interact with the FPGA and enough resources to run a simple softcore, like a small RISC-V core.
248 parts3 - 4 layers190 × 70 mm

Questions
How big is the AquaMQTT PCB?
It measures 45 × 65 mm and has 2 copper layers, 1.6 mm thick.
What parts does the AquaMQTT use?
16 parts, built around the SN74LVC2T45DCURE4. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the AquaMQTT KiCad files?
From the tspopp/AquaMQTT repository on GitHub, at the commit this page was made from: the board is pcb/AquaMQTT.kicad_pcb and its schematic pcb/AquaMQTT.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the AquaMQTT design in my own project?
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).