Skip to the content
4 layers48.5 × 33.5 mmHFLink Plus, the printed circuit board in 3D

完全使用FPGA实现的高速DAP

Size
48.5 × 33.5 mm
Copper layers
4
Thickness
1.6 mm
Parts
130
Nets
165
Pads
528
Tracks, vias
872, 159
Pours
10
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
12 Dec 2025
Updated
20 Jun 2026

Overview

HFLink Plus is an open-source printed circuit board by LX050724, from the LX050724/HFLink repository on GitHub, published under the Apache-2.0 licence. It is a 4-layer board of 48.5 × 33.5 mm with 130 parts on 165 nets, routed with 872 tracks and 159 vias.

It is built around the SN74LVC1G125DCK, LMV358 and USB3320C-EZK, with the ADS1115IDGS, SN74LVC2T45DCURE4 and ECMF02-2AMX6 among its other parts. Its parts include 48 resistors, 33 capacitors, 15 ICs, 6 connectors and 3 diodes.

Main components

12

README

readme.md

HFLink

完全使用FPGA实现的高速DAP

硬件能力:

HFLink Plus敬请期待
硬件规格:
Power supplyUSB
Download speed into RAM3867KB/s@60MHz SWD
Max. target interface speed60MHz
Max. SWO speed100MHz
Max. VCOM speed/baudrate15 MBd
Max. SPI interface speed30MHz
Supported target voltage1.65 V - 5 V
Ethernet❌️
USB✅️
WiFi❌️
目标接口:
SWD✅️
JTAG✅️
VCOM✅️

SWD/JTAG:

最大时钟60MHz,时钟连续均匀,支持时序延迟补偿,带宽接近理论最大值

image-20260517010340973

注:逻辑分析仪触发电平和采样率问题导致占空比和频率显示有微小偏差

LED:

支持两种模式可在上位机随意切换

  • 默认模式
    1. 红色:目标电压低
    2. 绿色:目标电压正常
    3. 黄色:复位信号低
    4. 熄灭/不规律闪烁:DAP正在执行命令,熄灭时间表示执行时间
  • CMSIS-DAP模式
    1. 绿色:空闲
    2. 蓝色:已连接
    3. 紫色:运行中

SWO:

四倍过采样最高100M波特率,使用跳变沿对齐时间极大提高波特率误差容忍

NRZ模式支持小数分频,波特率计算公式 3200M/n (n>=32)

Manchester支持大容差无需小数分频,波特率计算公式200M/n (n>=2)

TODO:

  • VTRG电压&5V电流读取 ⬅️需开发上位机
  • SPI ⬅️需开发上位机
  • 线路延迟自标定⬅️需开发上位机

构建&下载方法:

  1. 打开高云FPGA工程,调整include路径配置
  2. 重新生成M1 IP核,其他IP核不需要生成
  3. 综合生成FPGA比特流
  4. 编译MCU代码自动生成合并MCU程序的比特流文件bitstream.bin
  5. 高云下载器设置Debugging/Temporary Mode -> Set ExFlash QE For Arora V使能Flash的Quad模式(仅需一次)
  6. 高云下载器设置External Flash Mode Arora V -> exFlash Erase,Program,Verify Arora V进行外部Flash下载

Parts

130
QtyValueFootprintReferences
22100nF,16VCapacitor_SMD:C_0402_1005MetricC1, C2, C12, C15, C16, C17, C18, C19, C20, C21, C22, C23, C24, C25, C26, C27 +6
15~Library:test_point_0.5mmTP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11, TP12, TP13, TP14, TP15
1310K,1%Resistor_SMD:R_0402_1005MetricR1, R19, R21, R22, R25, R26, R27, R32, R34, R35, R39, R47, R48
1033R,1%Resistor_SMD:R_0402_1005MetricR7, R18, R20, R28, R40, R41, R42, R44, R45, R46
90R,1%Resistor_SMD:R_0402_1005MetricR8, R9, R10, R11, R12, R13, R14, R15, R16
7SN74LVC2T45DCURPackage_SO:VSSOP-8_2.3x2mm_P0.5mmU4, U5, U6, U7, U9, U12, U13
61K,1%Resistor_SMD:R_0402_1005MetricR2, R23, R24, R36, R37, R38
64.7uF,10VCapacitor_SMD:C_0402_1005MetricC5, C6, C7, C13, C14, C29
44.7K,1%Resistor_SMD:R_0402_1005MetricR29, R30, R31, R33
4600Ω@100MHzInductor_SMD:L_0402_1005MetricFB1, FB2, FB3, FB4
4MountingHole_PadMountingHole:MountingHole_2.2mm_M2_ISO7380_Pad_TopBottomH1, H2, H3, H4
32.2nF,50VCapacitor_SMD:C_0402_1005MetricC8, C11, C33
35.1K,1%Resistor_SMD:R_0402_1005MetricR4, R5, R6
3SN74LVC1G125DCKPackage_TO_SOT_SMD:Texas_R-PDSO-G5_DCK-5U3, U10, U11
2DF40C-60DS-0.4V(51)Library:BTB-DF40C-60DS-0.4V(51)#J1, J2
2NCD0603G1LED_SMD:LED_0603_1608MetricD4, D5
1100K,1%Resistor_SMD:R_0402_1005MetricR43
1100mR,1%,1WResistor_SMD:R_1206_3216MetricR17
110nF,50VCapacitor_SMD:C_0402_1005MetricC10
110pF,50VCapacitor_SMD:C_0402_1005MetricC9
18.06K,1%Resistor_SMD:R_0402_1005MetricR3
1ADS1115IDGSPackage_SO:TSSOP-10_3x3mm_P0.5mmU14
1Conn_01x08_PinConnector_PinHeader_1.27mm:PinHeader_1x08_P1.27mm_VerticalJ6
1Conn_ARM_JTAG_SWD_20Connector_IDC:IDC-Header_2x10_P2.54mm_HorizontalJ3
1ECMF02-2AMX6Package_DFN_QFN:ST_UQFN-6L_1.5x1.7mm_P0.5mmU1
1LED_RGBALibrary:LED_RGBA_1615D6
1LMV358Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU15
1MT9700Package_TO_SOT_SMD:SOT-23-5U8
1SI2305Package_TO_SOT_SMD:SOT-23-3Q1
1SMD0603-050-6Fuse:Fuse_0603_1608MetricF1
1USB3320C-EZKPackage_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mmU2
1USB_C_Receptacle_USB2.0_16PConnector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12J4
1WAFER-ZH1.5-4PWBLibrary:ZH_SM04_1.50mm_HorizontalJ5

Similar boards

  • 4 layers68.6 × 53.3 mmSFduino UNO S2, the printed circuit board in 3D

    SFduino UNO S2

    HalfSweet/SFduino-UNO-S2

    SF32LB52 Devkit

    133 parts2
  • 2 layers64.8 × 74.5 mmReadingLampController, the printed circuit board in 3D

    ReadingLampController

    vsi5004/ReadingLampController

    A repurposing of my LCC Lighting Controller hardware into a customizable, Matter enabled, RGBW reading lamp

    67 parts
  • 4 layers107.1 × 32.4 mmAudio lab, the printed circuit board in 3D

    Audio lab

    AnterCreeper/shred

    electric guitar audio system

    132 partsGPL-2.0
  • 4 layers69.9 × 54 mmNx module breakout, the printed circuit board in 3D

    Nx module breakout

    tinyvision-ai-inc/pico2-nx

    RP2350+Lattice Crosslink NX FPGA board

    58 parts5MIT
  • 4 layers25.5 × 39.9 mmACM v1 r1, the printed circuit board in 3D

    ACM v1 r1

    akielaries/signalmesh_CAD

    signalmesh schematic and PCB files

    38 parts
  • 6 layers55 × 95 mmEcho r1-rev1, the printed circuit board in 3D

    Echo r1-rev1

    amachronic/echoplayer

    Echo - Open Hardware Music Player

    154 parts281CERN-OHL-S-2.0

Questions

How big is the HFLink Plus PCB?

It measures 48.5 × 33.5 mm and has 4 copper layers, 1.6 mm thick.

What parts does the HFLink Plus use?

130 parts, built around the SN74LVC1G125DCK, LMV358, USB3320C-EZK and ADS1115IDGS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the HFLink Plus KiCad files?

From the LX050724/HFLink repository on GitHub, at the commit this page was made from: the board is Hardware/plus/HFLink_Plus.kicad_pcb and its schematic Hardware/plus/GW5A_LV25MG121N.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the HFLink Plus design in my own project?

Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).