Skip to the content
2 layers100 × 30 mmCornucopia, the printed circuit board in 3D

Mostly Eurorack projects

Size
100 × 30 mm
Copper layers
2
Thickness
1.6 mm
Parts
53
Nets
15
Pads
86
Tracks, vias
121, 146
Pours
3
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
16 Jan 2021
Updated
19 Sep 2026

Overview

Cornucopia is an open-source printed circuit board by tpcarlson, from the tpcarlson/synth-diy repository on GitHub. It is a 2-layer board of 100 × 30 mm with 53 parts on 15 nets, routed with 121 tracks and 146 vias.

It is built around the VX7805-500. Its parts include 9 capacitors, 8 connectors, 5 diodes, 4 resistors and 3 ICs. It belongs with the audio and music boards of this library.

Main components

1

README

vcadsr/README.md

VCADSR

What is this?

Voltage controlled ADSR, using the ElectricDruid EnvGen8 chip. The module provides voltage control over most parameters (Attack, decay, sustain, release, time, level) as well as manual control with sliders. There are also three switches for toggling the mode, linear/exponential, and a fifth stage called "punch" which adds a little bit more to the attack on an envelope.

The mode toggle switch allows for gated looping, just looping (Almost like an LFO), and normal ADSR mode.

How much power does it use?

As measured by the joranalogue Test 3, around 40mA on +12v and 30mA on -12v at peak. The 5v rail is unused.

Where does the design come from?

The schematic is really an extension of the reference design on the ElectricDruid site, with some changes to add LEDs, and cutting features that would otherwise take up more panel space than I was comfortable with - I dropped the attenuators for CV inputs in favour of nice big manual controls with linear potentiometers instead.

Are there any rare/weird parts used?

You'll need one of the EnvGen8 chips in order to make this function at all!

Are there any problems with the design?

Just a couple, which are corrected in the version here. First, the LEDs for gate and trigger had some issues drawing too much power due to an oversight in the schematic. As it turns out LEDs don't really like being driven without a resistor! Second, the panel design had the mode and linear/exponential graphics switched which makes operating it a little bit more confusing than it otherwise ought to be.

These problems are both fixed in the repository right now though, however the fixes are untested. If I make another run of these boards, I will verify that the fix worked and remove this whole section!

Do you have a BOM/Mouser cart/Tayda links?

Sorry, no. Things go out of stock so frequently it'd be a lot of work to keep these up to date. Everything in this project is easy to source though, so you should not have any trouble.

Other resources
  • Assembly instructions
  • Interactive BOM - This includes pre-soldered SMT parts as well as the through-hole parts. To use this, save the 'raw' view to your computer and open it in a web browser

Parts

53
QtyValueFootprintReferences
14LOGOLOGOG***, G***, G***, G***, G***, G***, G***, G***, G***, G***, G***, G***, G***, G***
45.1kwinterbloom:R_0603_HandSolderR1, R2, R3, R4
4Conn_01x01_PinDivergent:FASTON-928814-1J3, J6, J8, J9
4GNDMountingHole:MountingHole_3mm_PadH1, H2, H3, H4
322uwinterbloom:C_0805_HandSolderC2, C4, C7
222uwinterbloom:C_1206_HandSolderC6, C9
24.7uwinterbloom:C_0805_HandSolderC5, C8
2P78E12-2000winterbloom:Converter_DCDC_CUI_P78E-1000_THTU2, U3
2Val**corn:cornRef**, Ref**
1+12Vwinterbloom:LED_0805_Kingbright_APT2012D2
1-12Vwinterbloom:LED_0805_Kingbright_APT2012D3
1100uCapacitor_SMD:CP_Elec_8x10.5C1
110uwinterbloom:C_1206_HandSolderC3
122uHInductor_SMD:L_1210_3225Metric_Pad1.42x2.65mm_HandSolderL1
12AFuse:Fuse_2920_7451MetricF1
15Vwinterbloom:LED_0805_Kingbright_APT2012D4
1BARRIERDiode_SMD:D_SOD-128D1
1DC INwinterbloom:TerminalBlock_4UCON_1x02_P3.50mm_HorizontalJ4
1DC THRUwinterbloom:BarrelJack_CUI_PJ-102AH_HorizontalJ1
1DC THRUwinterbloom:TerminalBlock_4UCON_1x02_P3.50mm_HorizontalJ2
1DCINwinterbloom:LED_0805_Kingbright_APT2012D5
1Eurorack Powerwinterbloom:Eurorack_Power_2x8_Shrouded_LockJ7
1MOVwinterbloom:R_0805_HandSolderTH1
1OSHW-Logo_5.7x6mm_CopperSymbol:OSHW-Logo_5.7x6mm_CopperOSHW
1VX7805-500winterbloom:Converter_DCDC_CUI_VX78-500_THTU1

More from tpcarlson/synth-diy

12
  • 4 layers241.2 × 327.2 mmCyclic, the printed circuit board in 3D

    Cyclic

    tpcarlson/synth-diy

    Mostly Eurorack projects

    439 parts107
  • 2 layers293.3 × 128.5 mmTwoshot, the printed circuit board in 3D

    Twoshot

    tpcarlson/synth-diy

    Mostly Eurorack projects

    223 parts107
  • 4 layers179.5 × 128.5 mmSynth diy, the printed circuit board in 3D

    Synth diy

    tpcarlson/synth-diy

    Mostly Eurorack projects

    175 parts107
  • 4 layers313.1 × 185.6 mmOneshot, the printed circuit board in 3D

    Oneshot

    tpcarlson/synth-diy

    Mostly Eurorack projects

    172 parts107
  • 2 layers85.4 × 128.5 mmKinky lynx, the printed circuit board in 3D

    Kinky lynx

    tpcarlson/synth-diy

    Mostly Eurorack projects

    165 parts107
  • 2 layers286.9 × 128.7 mmLattice, the printed circuit board in 3D

    Lattice

    tpcarlson/synth-diy

    Mostly Eurorack projects

    161 parts107
  • 2 layers40.3 × 109.6 mmImpact main, the printed circuit board in 3D

    Impact main

    tpcarlson/synth-diy

    Mostly Eurorack projects

    159 parts107
  • 2 layers191.3 × 128.5 mmSycamore, the printed circuit board in 3D

    Sycamore

    tpcarlson/synth-diy

    Mostly Eurorack projects

    149 parts107
  • 4 layers179.1 × 128.5 mmVcadsr, the printed circuit board in 3D

    Vcadsr

    tpcarlson/synth-diy

    Mostly Eurorack projects

    149 parts107
  • 2 layers94.3 × 128.5 mmLeaky bucket, the printed circuit board in 3D

    Leaky bucket

    tpcarlson/synth-diy

    Mostly Eurorack projects

    137 parts107
  • 2 layers101.3 × 128.5 mm3-phase lfo, the printed circuit board in 3D

    3-phase lfo

    tpcarlson/synth-diy

    Mostly Eurorack projects

    129 parts107
  • 2 layers131.8 × 57.6 mmRowan, the printed circuit board in 3D

    Rowan

    tpcarlson/synth-diy

    Mostly Eurorack projects

    115 parts107

Similar boards

  • 4 layers80 × 70 mmJellyfish, the printed circuit board in 3D

    Jellyfish

    wntrblm/jellyfish-and-starfish

    Jellyfish and Starfish are control boards designed for use with the LumenPnP. Starfish controls the base of the machine including X & Y axes and pneumatics.

    172 parts112
  • 2 layers80 × 95 mmLaserBoard, the printed circuit board in 3D

    LaserBoard

    matthewSorensen/pewpew-laserboard

    LaserBoard is an open source controller for fiber laser marking systems, based around a Teensy 4.1 MCU board. LaserBoard provides a USB interface compatible with most low-cost fiber laser sources and XY-100-speaking…

    123 parts10CERN-OHL-S-2.0
  • 4 layers189.4 × 59.1 mmFlippyDriver, the printed circuit board in 3D

    FlippyDriver

    NietoSkunk/FlippyDriver

    Driver board for Luminator MAX3000 Flip Dot Panels

    344 parts10MIT
  • 2 layers217.1 × 393.8 mmSweepv2, the printed circuit board in 3D

    Sweepv2

    davidphilipbarr/Sweep

    Sweep - a small promicro based keyboard inspired by the Ferris.

    53 parts2.1k
  • 2 layers121.9 × 81.3 mmRgb to hdmi, the printed circuit board in 3D

    Rgb to hdmi

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    53 parts1kGPL-3.0
  • 2 layers48 × 48 mmUSB, the printed circuit board in 3D

    USB

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    53 parts915
  • 2 layers103.7 × 74.1 mmPicoGUS, the printed circuit board in 3D

    PicoGUS

    polpo/picogus

    Emulation of ISA sound cards and CD-ROM on Raspberry Pi Pico (GUS, SB/Adlib, MPU-401, Tandy, CMS, Panasonic CD-ROM) with USB mouse/joystick support

    53 parts805

Questions

How big is the Cornucopia PCB?

It measures 100 × 30 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Cornucopia use?

53 parts, built around the VX7805-500. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Cornucopia KiCad files?

From the tpcarlson/synth-diy repository on GitHub, at the commit this page was made from: the board is cornucopia/hardware/cornucopia/board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Cornucopia design in my own project?

Its repository states no licence, so its author keeps all rights: ask tpcarlson before reusing the design.