
Doper Dactyl
Dopernieux/dactyl-manuform-wireless
Ergonomic split mechanical keyboard - Dactyl Manuform BLE Flex PCB project

Battery Management System (BMS) with Buck-Boost Converter
Bms buck boost is an open-source printed circuit board by tor1kk, from the tor1kk/bms-buck-boost repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 35.1 × 28.9 mm with 38 parts on 25 nets, routed with 81 tracks and 36 vias.
It is built around the TPS63020DSJR, DW01A and 1N5819WS, with the AO3401A, FS8205A and LESD5D5.0CT1G among its other parts. Its parts include 11 capacitors, 9 resistors, 4 diodes, 3 ICs and 3 connectors. It belongs with the power boards of this library.
This Battery Management System (BMS) with Buck-Boost Converter is designed for lithium battery applications, providing a flexible voltage range of 3-5V. It is particularly useful in projects requiring stable 3.3V or 5V outputs. The system includes a charging circuit, protection circuit, and a DC-DC buck-boost converter, ensuring consistent voltage, enhanced battery safety, and adaptability for various devices.
The key components of the module include:
Charging Circuit: Utilizing the MCP73831, this circuit facilitates the selection of charge current via a resistor and incorporates an indicator diode.
Protection Circuit: Protection is ensured by DW01A and FS8205A. The FS8205A connects the battery's negative to the common ground, with DW01A controlling battery operation. The transistor disconnects the battery in cases of discharge, overcharge, short circuit, etc.
DC-DC Buck-Boost Converter: Employing TPS63020DSJR, this component enables voltage conversion. The goal is to maintain a constant voltage level regardless of the battery charge, acting as a step-up converter when voltage is low and a step-down converter when it's high.
In summary, this module facilitates battery charging, provides protection, and allows for adjustable output voltage.
Refer to the complete schematic in
BMS_Buck-Boost.pdf.

-B and +B are used to connect the battery.+B, +V, and GND are for connecting to the load, with +B used for measuring battery voltage.VBUS line is high. At this point, transistor Q2 (refer to the schematic here) doesn't pass the voltage. This is done to optimize battery charge. If you want to use VBUS for the DC-DC converter during charging, employ diode D4 and an additional diode to prevent current from +VCC_IN to +BATT.| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 22uF | Capacitor_SMD:C_0805_2012Metric | C7, C8, C9, C10 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_2.2mm_M2_DIN965_Pad | H1, H2, H3, H4 |
| 2 | 100nF | Capacitor_SMD:C_0805_2012Metric | C3, C6 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric | C4, C5 |
| 2 | 1N5819WS | Diode_SMD:D_SOD-323F | D3, D4 |
| 2 | 2K | Resistor_SMD:R_0603_1608Metric | R1, R4 |
| 2 | 4.7uF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C1, C2 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 1 | 1,1M | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | 100K | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV1 |
| 1 | 100R | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 100uF | Capacitor_Tantalum_SMD:CP_EIA-3528-21_Kemet-B | C11 |
| 1 | 120K | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 2.2uH | Inductor_SMD:L_Chilisin_BMRx00060630 | L1 |
| 1 | 50K | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | Conn_01x02_Pin | Cutom_PinHeaders:PinSocket_1x02_P2.54mm_Vertical | J2 |
| 1 | Conn_01x03_Pin | Cutom_PinHeaders:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | DW01A | footprints:SOT23-6 | U2 |
| 1 | FS8205A | footprints:SOP65P640X120-8N | Q1 |
| 1 | LED | Diode_SMD:D_0805_2012Metric | D1 |
| 1 | LESD5D5.0CT1G | Diode_SMD:D_SOD-523 | D2 |
| 1 | MCP73831-2-OT | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | TPS63020DSJR | footprints:IC_TPS63020DSJR | U3 |
| 1 | USB_C_Receptacle_PowerOnly_6P | Connector_USB:USB_C_Receptacle_GCT_USB4125-xx-x-0190_6P_TopMnt_Horizontal | J1 |

Dopernieux/dactyl-manuform-wireless
Ergonomic split mechanical keyboard - Dactyl Manuform BLE Flex PCB project


Sumya99/RobotCarPCB
NAND сургалтын төвийн сурагчдад зориулсан робот машины PCB төсөл

Projeto-Guarda-Rios/PCB
O repositório para a PCB do Projeto Guarda Rios! Inclui todos os ficheiros relacionados com a PCB!


Tinkerbug-Robotics/TinkerRocket
Model rocket flight computer, ground station, iOS app, and simulation


It measures 35.1 × 28.9 mm and has 2 copper layers, 1.6 mm thick.
38 parts, built around the TPS63020DSJR, DW01A, 1N5819WS and AO3401A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the tor1kk/bms-buck-boost repository on GitHub, at the commit this page was made from: the board is BMS_Buck-Boost.kicad_pcb and its schematic BMS_Buck-Boost.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).