Skip to the content
2 layers250 × 189 mmKeypad, the printed circuit board in 3D

lighting focused midi controller

Size
250 × 189 mm
Copper layers
2
Thickness
1.6 mm
Parts
76
Nets
64
Pads
281
Tracks, vias
292, 13
Pours
10
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
8 Jul 2024
Updated
31 Jan 2025

Overview

Keypad is an open-source printed circuit board by Tommie1236, from the Tommie1236/midi-controller repository on GitHub, published under the CERN-OHL-W-2.0 licence. It is a 2-layer board of 250 × 189 mm with 76 parts on 64 nets, routed with 292 tracks and 13 vias.

It is built around the DRV8210DRL, MTCH102-I/MS and TCA8418RTW, with the RSA0N11M9A0J among its other parts. Its parts include 49 switches, 10 connectors, 6 capacitors, 6 resistors and 3 ICs. It belongs with the audio and music and lEDs and displays boards and the RP2040 boards of this library.

Main components

4

README

README.md

Build firmware Build fader-wing

huge thanks to the amazing rp2040 skeleton project. it helped immensly setting up this project. i probably couldn't have done it without

<still need good name :)>

A lighting focused midi controller

Why?

I started this project as i wanted phisical controls to go with the mydmx3 dmx controller software.
Mydmx3 practicly only support midi as data in/out next to dmx out. So a midi controller it is.
There are more than enough midi controllers on the market but almost all of them are audio focused in the controls. I couldn't really vind any that i would like for controlling lighting. So i decided to design and build my own.

Requirements

I set a couple of requirements that i definetly wanted in my controler. As following:

Controls:
  • motorized faders. Mostly for dimming controls, enough in the playback section and 1 as Master.
    I chose motorized so they could sync with the controlling software if the value changes and for for example if you were to switch banks to a new set of controls. (mydmx doesn't support that but i wanted to design my controller to work with almost anything.)

  • Buttons. for playbacks/executors en general control, a whole lot.
    Of Course. what would a controller be without a lot of buttons. I also want them to have black with transparent text keycaps and rgb leds below to show the status of the button.

  • Encoders. Mostly speed control but could also be dimmer, at least 1 per "channel"/collumn and a couple spare. I wanted some encoders to be able to change the speed of scene/cue playbacks. But also for for example a dimmer channel dat isn't changed often but often enough to have phisical controls for.

  • Small Displays/Scribble Strips. channel/collumn names, one per channel/collumn.
    To show what cue/scene was mapped to that channel/collumn. If i implement bank switching inside the controller (as mydmx doesn't support like anything. only the most basic midi triggering) i want to see what cue i have mapped on that fader/buttons. And maybe also to show the fader/encoder value when changing. For if you want it to a specific value and the visual position isn't enough.

  • Keypad. just one, numbers 0-9 + some modifiers.
    Should speak for itself. just general number inputs and modifiers.

  • "Master" Display. (relatively) big display, just one.
    A around 3a4" touch display for configuration of the controller and general info. Main controls for anything happening inside the controller.

  • Leds. A lot. most RGB some just Amber.
    I want all the buttons to have a seperate controllable RGB led to show the buttons status. and about 16 mono Amber leds around the encoders to show their value.

Conectivity:
  • usb midi. one usb-B port. To connect to a pc running for example mydmx.

  • hardware midi. 2 or 3 din-5 ports. To connect to other midi gear or any controller that has hardware midi ports on it. Should have the same data as the usb midi port

  • External Switch Ports. 2a3 x 1/4" jack. To connect external footswitches or pedals. should support normal on/off footswitches and maybe one or 2 can have analog value support.

  • Desk Light. xlr-4?. A xlr connector that support a lot of desk lights. preferably xlr-4 so it isn't confused with audio or dmx signals. Sadly there isn't a standard for desk ligths as far as i can find.

  • Powercon Socket. Blue one. maybe also power out.
    Of cource. It needs some power to run. prefereably powercon (true1??) but a C14 socket would also work.
    with the motor faders and a lot of leds. Usb supplied power wont be enough.

And here are some features i want to support but arent required for the mvp:
  • USB Hub. Probably USB-A sockets.
    To connect more devices downstream from the controller

  • RTP MIDI. Wifi/Ethernet
    Using a ESP32 or similar to handle the network stack and enable the controller to communicate either wireless or via a ethernet cable.
    Adding to the already available midi connection options of USB-MIDI and hardware-MIDI

  • Web Server.
    Maybe a configuration webserver as the display will be quite small. would also run on the ESP32 that handels the network.
    it connects to the main rp2040 using uart.

Parts

76
QtyValueFootprintReferences
48SW_SPSTButton_Switch_Keyboard:SW_Cherry_MX_1.00u_PlateSW11, SW27, SW28, SW29, SW30, SW31, SW32, SW33, SW34, SW35, SW36, SW37, SW38, SW39, SW40, SW41 +32
8Conn_01x04_SocketConnector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_VerticalJ23, J24, J25, J26, J27, J28, J29, J30
44K7Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR28, R29, R30, R31
3100nCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC34, C36, C52
210KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR20, R21
21uCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC33, C35
11.05" 130*240 spi screenpersonal:1.05' 120x240 spi screenDS1
1100uCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC51
1Conn_01x02_SocketConnector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_VerticalJ17
1Conn_01x05_SocketConnector_JST:JST_PH_B5B-PH-K_1x05_P2.00mm_VerticalJ1
1DRV8210personal:SOT-6U18
1MTCH102Package_DFN_QFN:DFN-8-1EP_3x2mm_P0.5mm_EP1.3x1.5mmU16
1RSA0N11M9A0Jpersonal:RSA0N11M9A0JMF1
1SW_SPSTButton_Switch_Keyboard:SW_Cherry_MX_2.00u_Vertical_PlateSW81
1TCA8418Package_DFN_QFN:WQFN-24-1EP_4x4mm_P0.5mm_EP2.45x2.45mmU7

More from Tommie1236/midi-controller

3
  • 4 layers123.8 × 362.3 mmMidi controller, the printed circuit board in 3D

    Midi controller

    Tommie1236/midi-controller

    lighting focused midi controller

    516 parts2CERN-OHL-W-2.0
  • 2 layers160.5 × 288 mmFaders, the printed circuit board in 3D

    Faders

    Tommie1236/midi-controller

    lighting focused midi controller

    348 parts2CERN-OHL-W-2.0
  • 2 layers80 × 42.1 mmMIDI, the printed circuit board in 3D

    MIDI

    Tommie1236/midi-controller

    lighting focused midi controller

    24 parts2CERN-OHL-W-2.0

Similar boards

  • 2 layers99.4 × 38.6 mmSlider driver, the printed circuit board in 3D

    Slider driver

    mage0r/RSA0N11M9A0J_motorised_slider

    This is a H-bridge driver board for the RSA0N11M9A0J motorised Slider. It uses a L9110 and capacitive sensor.

    38 parts7
  • 2 layers43.9 × 24.3 mmVlvts, the printed circuit board in 3D

    Vlvts

    hubertmis/zathome

    Smart home embedded devices based on Zephyr OS

    34 parts5
  • 4 layers37.2 × 26 mmIEMU Vib Eval, the printed circuit board in 3D

    IEMU Vib Eval

    ponderononon/IEMU_DevBoards

    Kicad Schematic Files for the BASE and SENSOR Development Boards (Layout in Progress)

    11 parts
  • 2 layers74.3 × 69.9 mmPreAmpPico, the printed circuit board in 3D

    PreAmpPico

    smileym4n-collab/Kicadprojects

    72 parts
  • 2 layers192.4 × 50 mmOmote, the printed circuit board in 3D

    Omote

    OMOTE-Community/OMOTE-Hardware

    Open Source Remote - Hardware

    187 parts157GPL-3.0
  • 2 layers97.2 × 81.3 mmRadiotxt, the printed circuit board in 3D

    Radiotxt

    AnthonyDiGirolamo/i2c-thumb-keyboard

    Handheld tactile switch keyboard using the TCA8418.

    85 parts30MIT
  • 2 layers149.9 × 167.6 mmCollins FMS-3000, the printed circuit board in 3D

    Collins FMS-3000

    neilenns/Collins-FMS-3000

    PCB for a replica Collins FMS-3000 to use with MobiFlight

    126 parts6MIT
  • 2 layers60 × 55 mm3x4 keyboard, the printed circuit board in 3D

    3x4 keyboard

    Tomas-Kuchta-FPV/Travel-Buddy

    Pocketable, smart and sleek Meshtastic node. With keyboard, Eink screen, GPS and all day baterry life thanks to it's Solar panel and nRF52 in Wio tracker L1.

    33 parts6CERN-OHL-W-2.0

Questions

How big is the Keypad PCB?

It measures 250 × 189 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Keypad use?

76 parts, built around the DRV8210DRL, MTCH102-I/MS, TCA8418RTW and RSA0N11M9A0J. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Keypad KiCad files?

From the Tommie1236/midi-controller repository on GitHub, at the commit this page was made from: the board is kicad/keypad.kicad_pcb and its schematic kicad/Fader-Leds.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Keypad design in my own project?

Its repository publishes it under the CERN-OHL-W-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).