

Pico ice
Raspberry Pi PICO board + Lattice iCE40 FPGA's
- Size
- 22.9 × 61 mm
- Copper layers
- 4
- Thickness
- 1.58 mm
- Parts
- 109
- Nets
- 96
- Pads
- 447
- Tracks, vias
- 1,537, 178
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 7 Feb 2021
- Updated
- 4 Jul 2025
Overview
Pico ice is an open-source printed circuit board by tinyvision-ai-inc, from the tinyvision-ai-inc/pico-ice repository on GitHub, published under the MIT licence. It is a 4-layer board of 22.9 × 61 mm with 109 parts on 96 nets, routed with 1,537 tracks and 178 vias.
It is built around the ICE40UP5K-SG48I, RP2040 and W25Q32JVSSIQ, with the APS6404L-3SQN-SN, CL9293A12L5M and RC0402FR-0710KL among its other parts. Its parts include 41 capacitors, 25 resistors, 10 connectors, 7 ICs and 4 diodes. It belongs with the fPGA and programmable logic boards and the RP2040 and FPGA and CPLD boards of this library.
Main components
12ICE40UP5K-SG48I
QFN-48-EP(7x7)-40℃~+100℃ 1.14V~1.26V 1171456bit 39 5280 660 iCE40 UltraPlus QFN-48-EP(7x7) Programmable Logic Device (CPLDs/FPGAs) ROHSLatticeProgrammable Logic Device (CPLDs/FPGAs)RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q32JVSSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 133MHz 1uA 2.7V~3.6V 20 Years 32Mbit 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHAPS6404L-3SQN-SN
SOP-8LSOP-8L DRAM ROHSAP MemoryDRAMCL9293A12L5M
SOT-23-5-40℃~+85℃ 1 1.2V 100mV@(100mA) 400mA 50uVrms 60uA 6V 75dB@1kHz Fixed Over Current Protection、Short Circuit Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSChipLink TechLinear Voltage Regulators (LDO)RC0402FR-0710KL
UncategorisedUnknown makerDW254W-22-12-85
弯插,P=2.54mm12P 2 2.54mm 2.54mm 2x6P 3A 8.5mm Right Angle Side Square Hole 弯插,P=2.54mm Female Headers ROHSDEALONFemale HeadersEMK105BJ105KV-F
040216V 1uF X5R ±10% 0402 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSTaiyo YudenMultilayer Ceramic Capacitors MLCC - SMD/SMTDW254W-22-06-85
弯插,P=2.54mm2 2.54mm 2.54mm 2x3P 3A 6P 8.5mm Right Angle Side Square Hole 弯插,P=2.54mm Female Headers ROHSDEALONFemale HeadersMHPA1010RGBDT
SMD-4P,1x1mm-40℃~+85℃ 0.6mm 120° 1mm 1mm Black frosted lens Common Anode G:525.5nm~533.5nm、R:619.5nm~624.5nm、B:463.5nm~471.5nm R:1.7V~2.3V、G:2.5V~3.5V、B:2.5V~3.5V R:17.7mcd~30.0mcd、G:27.6mcd~53.9mcd、B:5.9mcd~11.6mcd R:2000V、G:1000V、B:1000V R:20mA、G:20mA、B:20mA R:50mW、G:60mW、B:60mW SMD-4P,1x1mm RGB LEDs ROHSMEIHUARGB LEDsABM10-166-12.000MHZ-T3
SMD2520-4P-20℃~+70℃ 125Ω 12MHz 8pF ±10ppm ±10ppm SMD2520-4P Crystals ROHSAbraconCrystals1N4148WT-7-CN
SOD-523SOD-523 Switching Diodes ROHSChipNoboSwitching Diodes
README
README.mdpico-ice
Doc | Hardware | SDK | Schematic | Assembly | Discord

PCB Design Files, Designs, Documentation
The pico-ice is a small, low cost board with the Raspberry Pi Pico processor (RP2040) and a Lattice Semiconductor iCE40UP5K FPGA. The board features independent flash for the FPGA and RP2040, low power SSRAM, a couple of pushbuttons and a 3 color LED with all FPGA and RP2040 pins brought out to easy to use 0.1" header pins (arranged as PMOD's) for fast prototyping.
The tinyVision.ai pico-ice Board Features:
- RaspberryPi RP2040 processor
- Lattice UltraPlus ICE40UP5K FPGA with 5.3K LUTs, 1Mb SPRAM, 120Kb DPRAM, 8 Multipliers
- ALL RP2040 and 32 FPGA GPIO on 0.1” headers
- 4MB SPI Flash
- 8MB low power qSPI SRAM
- RGB LED, shared between the RP2040 and FPGA
- 2 pushbuttons, 1 dedicated and 1 primarily for processor reset during development but can be repurposed for user applications when not used for reset
- On board 3.3V and 1.2V Regulators, can supply 3.3V to your project
- Open source schematic and layout using KiCAD design tools
- 4 layer board with a solid ground plane for good signal integrity
- FPGA clock supplied by the RP2040, easy to program FPGA clock under SW control
- Examples for communicating to the FPGA over SPI
- Support for ultra low power sleeep mode: can shut down the RP2040 and FPGA while keeping the SRAM powered
Firmware features:
- pico-ice library to support drag-drop programming of the FPGA bitfile: no need of any dedicated programmer
- Alternate programming of the FPGA flash using DFU mode
- FPGA clock under RP2040 control
- Passthrough UART code enables transparent access to the FPGA's UART for debug/logging/control
OSHW US002140 | Certified open source hardware | oshwa.org/cert
Parts
109| Qty | Value | Footprint | References |
|---|---|---|---|
| 26 | 0.1u | Capacitor_SMD:C_0402_1005Metric | C10, C12, C14, C15, C16, C17, C18, C19, C20, C21, C23, C24, C26, C27, C28, C29 +10 |
| 11 | 4.7u | Capacitor_SMD:C_0402_1005Metric | C3, C7, C9, C13, C22, C25, C30, C31, C32, C34, C43 |
| 9 | 10K | Resistor_SMD:R_0402_1005Metric | R7, R8, R9, R12, R13, R15, R16, R17, R21 |
| 6 | 27 | Resistor_SMD:R_0402_1005Metric | R4, R5, R6, R22, R23, R25 |
| 6 | Fiducial | Fiducial:Fiducial_0.75mm_Mask1.5mm | FID1, FID2, FID3, FID4, FID5, FID6 |
| 5 | 6X2 Female Header | CUSTOM:PMOD_2x06_P2.54mm_Horizontal | J3, J4, J6, J7, J8 |
| 4 | 2.2K | Resistor_SMD:R_0402_1005Metric | R14, R18, R19, R20 |
| 4 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5 | H1, H2, H3, H4 |
| 3 | SHORT | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | SJ1, SJ4, SJ5 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C6, C11 |
| 2 | 27p | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 2x3_2.54mm_Female | Connector_PinSocket_2.54mm:PinSocket_2x03_P2.54mm_Horizontal | J10, J11 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric | R10, R24 |
| 2 | MHPA1010RGBDT | CUSTOM:LED_Cree-PLCC4_1x1mm_CW | D2, D4 |
| 2 | PTS820 J25K SMTR LFS | CUSTOM:PTS820J25KSMTRLFS | SW1, SW2 |
| 2 | W25Q32JVSSIQ | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U2, U8 |
| 1 | 100 | Resistor_SMD:R_0402_1005Metric | R11 |
| 1 | 12 MHz | Crystal:Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | 1N4148WT-7 | Diode_SMD:D_SOD-523 | D1 |
| 1 | APS6404L-3SQN-SN | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | BOOT_SEL | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J9 |
| 1 | CL9293A12L5M | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | DNP | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | ICE40UP5K-SG48ITR | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U6 |
| 1 | LTST-C191KGKT | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | MF-FSMF035X-2 | Resistor_SMD:R_0603_1608Metric | PTC1 |
| 1 | NCP1117ST33T3G | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | OPEN | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | SJ6 |
| 1 | Pb free Logo | CUSTOM:Pb free logo | LOGO3 |
| 1 | RP2040 | RP2040_minimal:RP2040-QFN-56 | U3 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | WEEE Logo | CUSTOM:WEEE logo | LOGO2 |
| 1 | tinyVS Logo | CUSTOM:tinyAI_logo | LOGO1 |
More from tinyvision-ai-inc/pico-ice
2- 4 layers22.9 × 61 mm

- 4 layers22.9 × 61 mm

Similar boards
- 4 layers27.9 × 63.5 mm

Pico2-ice
tinyvision-ai-inc/pico2-ice
Doc | Hardware | SDK | Schematic | Assembly | Discord
124 parts60MIT - 2 layers89 × 83 mm

- 6 layers129.8 × 57.4 mm

- 4 layers60 × 33.3 mm

- 2 layers45 × 52.5 mm

Caravel breakout fpga ICE40UP5K TT3
TinyTapeout/breakout-pcb
Tiny Tapeout breakout PCBs
234 parts22Apache-2.0 - 4 layers100 × 100 mm

Pico Dev iCE
frohro/pico-dev-ice
This is a direct down conversion (DDC) HF transceiver & VNA using the Raspberry Pi Pico and the iCE40UP5K.
294 parts3 - 4 layers62 × 22.2 mm

UPduino v3.01
tinyvision-ai-inc/UPduino-v3.0
UPduino 3.0: new 4 layer layout, various other improvements
113 parts365MIT - 4 layers28 × 45 mm

SmartCard
dac63701/SmartCard
The goal of this project was to create a small and slim Bluetooth tracker that would fit into a credit card enclosure. To do this, a 0.8mm thin 80mah battery was used along with a 0.8mm PCB.
71 parts
Questions
How big is the Pico ice PCB?
It measures 22.9 × 61 mm and has 4 copper layers, 1.58 mm thick.
What parts does the Pico ice use?
109 parts, built around the ICE40UP5K-SG48I, RP2040, W25Q32JVSSIQ and APS6404L-3SQN-SN. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pico ice KiCad files?
From the tinyvision-ai-inc/pico-ice repository on GitHub, at the commit this page was made from: the board is Board/Rev0/pico-ice.kicad_pcb and its schematic Board/Rev0/pico-ice.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pico ice design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).


