Skip to the content
2 layers74.9 × 128.9 mmPIDController, the printed circuit board in 3D

Documents to help with reviewing printed circuit board designs for remote laboratory experiments

Size
74.9 × 128.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
34
Nets
72
Pads
155
Tracks, vias
211, 7
Pours
1
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
12 Nov 2021
Updated
22 Nov 2021

Overview

PIDController is an open-source printed circuit board by timdrysdale, from the timdrysdale/pcb-review repository on GitHub, published under the AGPL-3.0 licence. It is a 2-layer board of 74.9 × 128.9 mm with 34 parts on 72 nets, routed with 211 tracks and 7 vias.

It is built around the ARDUINO UNO R3, SN75175D and TXS0104ED. Its parts include 7 resistors, 6 connectors, 3 ICs and 2 capacitors. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

3

README

README.md

pcb-review

Documents to help with reviewing printed circuit board designs for remote laboratory experiments

Background

PCB design is often about keeping track of the impacts of lots of small tid bits of data. Small mistakes can range from the merely annoying to the moderately expensive. Some of the things that can go wrong with even relatively simple embedded systems include putting a footprint down that is the wrong size, or the wrong way up, getting the polarity of a connector backwards, getting pin headers that only take a round pin when your daughteroard is supplied with square pins, oversizing a track because you remembered the stall current from a motor wrong, forgetting to put pull-ups on an I2C bus, then adding them when they are not needed on a level shifting circuit which has it's own pullups, not leaving space around a terminal block to get wires in, leaving off mounting holes for the PCB, selecting the wrong pins on a microcontroller because you thought you'd use analogWrite then you device you want a different pulse width modulation frequency, so you need to use SAMD21_Turbo_PWM, needing to add a level shifter, needing to change the pin you get your 5V reference from when you change the arduino type from nano to nano every. Some of these have happened to us, and some of them nearly happened. Since there is an awful lot to keep a track of, I thought I'd try and formulate a design document that works for us (skip some of things we don't need to worry about, and add in some things that we do).

Ideally we'd also have a change control process so that we only have to sign off again on bits that have changed ...

A spreadsheet is probably a useful way to address this issue.

Usage of this repo

I'm assuming that the templates might be better kept up to date if the actual reviews are stored in the same repo - they can also be copied into the project repos, or done in the project repo and then copied in here - that way, boards with similar parts can find checks in pre-existing design reviews to draw on.

Suggested review folder structure: review.ods: the review spreadsheet design.md: any design descriptions, and useful notes e.g. checking orientation and sizing of parts. doc: datasheets and application notes pcb: the actual design files under review (complete, including all footprints)

text
├── example
│   ├── doc
│   └── pcb
└── pidcontrol2
    ├── doc
    └── pcb

Developer notes

A guide to conditional formatting in LibreOffice Calc is here

Parts

34
QtyValueFootprintReferences
7TestPointTestPoint:TestPoint_Pad_D2.0mmTP 3V3, TP A, TP B, TP I, TP leftPWM, TP rightPWM, TP VUSB
4Screw_Terminal_01x02TerminalBlock:TerminalBlock_bornier-2_P5.08mmJ3, J4, J5, J6
3200Resistor_SMD:R_0805_2012MetricR5, R6, R7
32kResistor_SMD:R_0805_2012MetricR2, R3, R4
20.1uFCapacitor_SMD:C_0805_2012MetricC1, C2
2SolderJumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mmJP1, JP2
2TestPointTestPoint:TestPoint_Pad_4.0x4.0mmTP GND, TP GND
15kResistor_SMD:R_0805_2012MetricR1
1Arduino_Nano_33_IoTMODULE_ABX00027U1
1Arduino_UNO_R3Module:Arduino_UNO_R3A1
1Conn_02x03_Odd_EvenConnector_PinSocket_2.54mm:PinSocket_2x03_P2.54mm_VerticalJ7
1Conn_02x05_Odd_EvenConnector_PinSocket_2.54mm:PinSocket_2x05_P2.54mm_VerticalJ1
1SN75175DSOIC127P600X175-16NU3
1TXS0104EDSOIC127P600X175-14NU2

The 30 most common of 34 parts.

Similar boards

  • 2 layers30.8 × 24.4 mmWii Bluetooth Replacement, the printed circuit board in 3D

    Wii Bluetooth Replacement

    JSnowden33/Wii-Bluetooth-Replacement

    This project is a full replacement for the Nintendo Wii's Bluetooth module. Emulation of the Bluetooth module is performed on the PIC32 based on rnconrad's emulator, while controller connectivity on the ESP32 is based…

    50 parts48GPL-3.0
  • 2 layers115.2 × 78.6 mmL0destar, the printed circuit board in 3D

    L0destar

    m4rkw/l0destar

    l0destar open-source tracker project

    164 parts43
  • 2 layers85 × 54 mmGps mezzanine, the printed circuit board in 3D

    Gps mezzanine

    96boards/mezzanine-community

    Repository for community designed mezzanine boards for the 96boards specification.

    182 parts32
  • 2 layers48.8 × 43.9 mmAmiga-500-usb kb stamp, the printed circuit board in 3D

    Amiga-500-usb kb stamp

    wiretap-retro/A500-USB-Keyboard-Adapter-RP2040

    A USB keyboard adapter for the Amiga 500 based on the Pi Stamp RP2040

    18 parts18
  • 2 layers55.2 × 53 mmAmiga-2000-usb kb stamp, the printed circuit board in 3D

    Amiga-2000-usb kb stamp

    wiretap-retro/A2000-USB-Keyboard-Adapter-RP2040

    A USB keyboard adapter for the Amiga 2000 based on the Pi Stamp RP2040

    14 parts11
  • 2 layers120.1 × 58.9 mmRte, the printed circuit board in 3D

    Rte

    3mdeb/rte-schematics

    Remote Test Evironment (RTE) sechematics.

    77 parts8
  • 2 layers161.9 × 73.7 mmTangNano20KDock, the printed circuit board in 3D

    TangNano20KDock

    hoglet67/TangNano20KDock

    A dock board for Beeb FPGA on the Tang Nano 20K

    84 parts3
  • 2 layersOTC, the printed circuit board in 3D

    OTC

    judge2005/OTC

    OneTubeClock KiCAD project

    82 parts3

Questions

How big is the PIDController PCB?

It measures 74.9 × 128.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the PIDController use?

34 parts, built around the ARDUINO UNO R3, SN75175D and TXS0104ED. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the PIDController KiCad files?

From the timdrysdale/pcb-review repository on GitHub, at the commit this page was made from: the board is reviews/pidcontrol2/pcb/PIDControllerV7/PIDController/PIDController.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the PIDController design in my own project?

Its repository publishes it under the AGPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).