
PicoFightingBoard
FeralAI/PicoFightingBoard
Open source PCB for arcade sticks using Raspberry Pi Pico.

This repository contains the firmware and host-side interface for controlling a WS2812 LED strip via an STM32 microcontroller over UART.
Mechatronics LED is an open-source printed circuit board by tigy1, from the tigy1/Mechatronics-Orin-LED repository on GitHub. It is a 4-layer board of 100 × 78 mm with 28 parts on 67 nets, routed with 147 tracks and 24 vias.
It is built around the SN74LV1T34DBV. Its parts include 12 capacitors, 3 resistors, 3 ICs, 3 connectors and 2 diodes. It belongs with the STM32 boards of this library.
This repository contains the firmware and host-side interface for controlling a WS2812 LED strip via an STM32 microcontroller over UART. The LEDs are used to indicate the current operational mode of the Orin Robosub, a student-built autonomous underwater vehicle.
Modes are communicated via UART from a Python script running on the host system and translated into LED color patterns by the STM32 firmware.
LEDs provide immediate visual feedback on Orin’s state. This is crucial during pool testing, debugging, or when operating the sub remotely. Modes are mapped to colors, enabling surface crew to distinguish between autonomous navigation, manual override, kill switch activation, and other states.
main.c)tan() mapping for perceived brightness tuningled_script.py)git clone https://github.com/tigy1/Mechatronics-Orin-LED.git
cd Mechatronics-Orin-LEDNUMBER_OF_LEDS is configured correctly in main.cmain.c and its dependencies (led.c, led.h) to your boardNo external libraries beyond pyserial are required:
pip install pyserialRun the Python control interface:
python3 led_script.pyYou will be prompted to enter RGB values in the format:
### ### ### where each chain of hashtags represents a number 001 - 255 (0s are important) as a decimal representation of RGB values.
To disable LED output via DMA, send: `001 000 000`The script will validate input and send it via UART to the STM32 board.
Adjust port and baudrate if needed inside led_script.py.
The STM32 expects newline-terminated ASCII RGB strings over UART:
"255 000 000\n"Parsed using sscanf in HAL_UART_RxCpltCallback().
Color bits are stored as bitwise-shifted PWM values in structs:
typedef struct {
uint16_t r[8], g[8], b[8];
} led;Brightness mapping uses tan(angle) to provide nonlinear control.
Each LED gets 24 bits; additional 2 LEDs are padded to ensure reset timing:
NUMBER_OF_LEDS * 24 + 2 * 24| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100nF | Capacitor_SMD:C_0603_1608Metric | C5, C6, C7, C8, C9, C12 |
| 2 | 30pF | Capacitor_SMD:C_0805_2012Metric | C3, C4 |
| 2 | 510R | Resistor_SMD:R_0805_2012Metric | R1, R3 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric | R2 |
| 1 | 10μF | Capacitor_SMD:C_0805_2012Metric | C2 |
| 1 | 16MHz | Crystal:Crystal_HC49-4H_Vertical | Y1 |
| 1 | 1μF | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 2.5pF | Capacitor_SMD:C_0805_2012Metric | C11 |
| 1 | 2pF | Capacitor_SMD:C_0805_2012Metric | C10 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | Conn_01x04 | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J3 |
| 1 | L78L33_SOT89 | Package_TO_SOT_SMD:SOT-89-3 | U1 |
| 1 | LED | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | PWR LED | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | SN74LV1T34DBV | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | STM32F103C6Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | ~ | Connector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_Vertical | J1 |
The 24 most common of 28 parts.

FeralAI/PicoFightingBoard
Open source PCB for arcade sticks using Raspberry Pi Pico.





the78mole/km271-wifi
A piece of hardware to be installed in a Buderus Logamatic 2107 to provide control and status over WiFi

ikajdan/katia
A split keyboard with 6 by 3 column staggered keys and 3 thumb keys, based on the Crkbrd design

crgarcia12/electronics-homeassistant-lightscontroll
A smart lighting controller PCB that integrates seamlessly with ESPHome and Home Assistant while maintaining full compatibility with traditional mechanical switches.
It measures 100 × 78 mm and has 4 copper layers, 1.6 mm thick.
28 parts, built around the SN74LV1T34DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the tigy1/Mechatronics-Orin-LED repository on GitHub, at the commit this page was made from: the board is Mechatronics LED.kicad_pcb and its schematic Mechatronics LED.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask tigy1 before reusing the design.