

Base Station v3b
TIGERs Mannheim Open-Source Electronics
- Size
- 58 × 85 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 130
- Nets
- 159
- Pads
- 650
- Tracks, vias
- 1,584, 470
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 18 Apr 2020
- Updated
- 9 Jul 2025
Overview
Base Station v3b is an open-source printed circuit board by TIGERs-Mannheim, from the TIGERs-Mannheim/electronics repository on GitHub. It is a 4-layer board of 58 × 85 mm with 130 parts on 159 nets, routed with 1,584 tracks and 470 vias.
It is built around the STM32F767VIT6, 74LVC1G125DBV and DP83848CVV, with the SKY66112-11, BMI-S-204-F and LP5907MFX-3.3 among its other parts. Its parts include 62 capacitors, 22 resistors, 10 ICs, 5 diodes and 5 inductors. It belongs with the STM32 boards of this library.
Main components
11STM32F767VIT6
LQFP-100(14x14)-40℃~+85℃ 1.7V~3.6V 216MHz 2MB 32 Bit 512KB 82 ARM Cortex-M7 Built-in FLASH LQFP-100(14x14) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)74LVC1G125DBV
SOT-23-5-40℃~+125℃ 1 1 1.65V~5.5V 10uA 3.1ns@3.3V,15pF 32mA 32mA 74LVC Power-off isolation、Output enable、Level shifting Tri-State Unidirectional SOT-23-5 Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, TransceiversDP83848CVV
LQFP48PHYTER™ QFP Single Port 10/100Mb/s Ethernet Physical Layer TransceiverTexas InstrumentsUncategorisedSKY66112-11
QFN-22-EP(3x3.5)-10dB -12dB -12dB -40℃~+85℃ -8dBm 0dBm 1.8V~3.6V 1uA 2.4GHz~2.483GHz 21dBm Bluetooth、ZigBee QFN-22-EP(3x3.5) RF Front End Circuits ROHSSkyworks SolutionsRF Front End CircuitsBMI-S-204-F
SMDSMD Modules ROHSLAIRD TECHNOLOGIESModulesLP5907MFX-3.3
SOT-23-5-40℃~+125℃@(Tj) 1 10uVrms 12uA 250mA 250mV@(250mA) 3.3V 5.5V 82dB@(1kHz) Fixed Positive Short Circuit Protection、Thermal shutdown、Enable control、Input under-voltage protection、Output discharge SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators3034TR
-- Battery Snap ROHSKeystone ElectronicsBatteryConnectorABS07W-32.768KHZ-D-1-T
SMD3215-2P-40℃~+85℃ 32.768kHz 3pF 55kΩ ±10ppm SMD3215-2P Crystals ROHSAbraconCrystalsCSTCR6M00G55-R0
SMD4520-3P-20℃~+80℃ 39pF 50Ω 6MHz SMD4520-3P Ceramic Resonators ROHSMurataCeramic ResonatorsFL520WFMT1
SMD3225-4P-40℃~+100℃ 12pF 30Ω 52MHz ±17ppm ±7ppm SMD3225-4P Crystals ROHSDiodes IncorporatedCrystalsSI-60062-F
插件1 Copper alloy Gold Non-PoE RJ45 Jack Right Angle Shielded With LED 插件 Ethernet Connectors / Modular Connectors (RJ45 RJ11) ROHSBel FuseEthernet Connectors / Modular Connectors (RJ45 RJ11)
README
README.mdTIGERs Mannheim Open-Source Electronics
This repository contains electronics for our robots and our base station. There is one folder for each released version.
Have a look at our 2020 ETDP which contains many details about design decisions and lessons learned over the last 10 years.
The following files are present for each release.
EAGLE
Electronics are designed with Autodesk EAGLE which is available for free for students. This folder contains all schematics (.sch) and board (.brd) files.
KiCad9
EAGLE files converted to KiCad version 9. Files got only a light cleanup pass. Note that no PCBs were ever produced using these files. The EAGLE files are still the ground truth.
All schematics are also available as PDF files. This makes it easier to view them without a need to install EAGLE.
CAM
CAM jobs for EAGLE. Used to produce manufacturing data from board files.
Gerber
Production ready zip packages for all boards. Most PCB production services directly accept gerber files.
Parts
130| Qty | Value | Footprint | References |
|---|---|---|---|
| 29 | 100n | Base Station v3b:C0603 | C1, C2, C11, C14, C16, C19, C20, C21, C22, C23, C24, C25, C26, C27, C28, C29 +13 |
| 10 | 100 | Base Station v3b:EXB28V | RN2, RN3, RN4, RN5, RN6, RN8, RN9, RN10, RN11, RN12 |
| 9 | 1k | Base Station v3b:R0603 | R1, R6, R7, R9, R10, R11, R12, R13, R22 |
| 9 | 1n | Base Station v3b:C0603 | C35, C37, C51, C53, C55, C59, C60, C61, C62 |
| 8 | 10u | Base Station v3b:C0603 | C9, C10, C15, C17, C18, C32, C57, C58 |
| 4 | 120R | Base Station v3b:0603 | L1, L3, L4, L5 |
| 4 | gr | Base Station v3b:CHIP-LED0603 | LED2, LED3, PWR0, UNK100MBIT0 |
| 3 | NA | Base Station v3b:C0402 | C40, C43, C48 |
| 2 | Base Station v3b:ANT-SMA-RA | X2, X3 | |
| 2 | 0p5 | Base Station v3b:C0402 | C33, C44 |
| 2 | 10n | Base Station v3b:C0603 | C46, C56 |
| 2 | 1k5 | Base Station v3b:R0603 | R4, R14 |
| 2 | 1p2 | Base Station v3b:C0402 | C41, C42 |
| 2 | 2k2 | Base Station v3b:R0603 | R15, R16 |
| 2 | 2n4 | Base Station v3b:R0402 | R19, R20 |
| 2 | 33 | Base Station v3b:R0603 | R2, R3 |
| 2 | 3n | Base Station v3b:R0402 | R18, R21 |
| 2 | 3p | Base Station v3b:C0603 | C12, C13 |
| 2 | 47p | Base Station v3b:C0402 | C39, C47 |
| 2 | 4k87 | Base Station v3b:R0603 | R8, R17 |
| 1 | Base Station v3b:dummyfp0 | UNK_HOLE_0 | |
| 1 | Base Station v3b:dummyfp1 | UNK_HOLE_1 | |
| 1 | Base Station v3b:dummyfp2 | UNK_HOLE_2 | |
| 1 | 0p7 | Base Station v3b:C0402 | C49 |
| 1 | 100p | Base Station v3b:C0402 | C38 |
| 1 | 10k | Base Station v3b:EXB28V | RN1 |
| 1 | 1M | Base Station v3b:R0603 | R5 |
| 1 | 1u | Base Station v3b:C0603 | C45 |
| 1 | 25MHz | Base Station v3b:7X | Q3 |
| 1 | 2u2 | Base Station v3b:IHLP1616 | L2 |
| 1 | 3034TR | Base Station v3b:CR2025 | X1 |
| 1 | 74LVC1G125DBV | Base Station v3b:SOT23-5 | IC1 |
| 1 | 93C76B | Base Station v3b:SOT23-6 | IC4 |
| 1 | ABS07W-32.768KHZ | Base Station v3b:CRYSTAL-07W | Q2 |
| 1 | BMI-S-204-F | Base Station v3b:SHIELD-32MM | U$1 |
| 1 | BUTTON4 | Base Station v3b:BUTTON4 | RESET1 |
| 1 | CP11009 | Base Station v3b:CP11009-THX | IC6 |
| 1 | CSTCR6M00G55-R0 | Base Station v3b:CSTCR6M | Q1 |
| 1 | DP83848CVV | Base Station v3b:LQFP48 | IC7 |
| 1 | FL520WFMT1 | Base Station v3b:CRYSTAL-7M | Q4 |
| 1 | FT2232ST | Base Station v3b:LQFP48-ST | IC2 |
| 1 | LP5907MFX-3.3 | Base Station v3b:SOT23-5L | IC10 |
| 1 | N/A | Base Station v3b:EXB28V | RN7 |
| 1 | SC189-3.3 | Base Station v3b:SOT23-5 | IC3 |
| 1 | SI-60062-F | Base Station v3b:RJ45-LED | ETH0 |
| 1 | SKY66112 | Base Station v3b:SMCM-22 | IC8 |
| 1 | STM32F767VIT6 | Base Station v3b:LQFP100-ST | IC5 |
| 1 | SX1280 | Base Station v3b:QFN24L | IC9 |
| 1 | USB-BU | Base Station v3b:USB-BMICRO | USB1 |
| 1 | rd | Base Station v3b:CHIP-LED0603 | LED1 |
More from TIGERs-Mannheim/electronics
8- 4 layers90 × 80 mm

- 4 layers80 × 85 mm

- 2 layers90 × 41 mm

- 2 layers140 × 85 mm

- 2 layers95 × 94 mm

- 2 layers82 × 14 mm

- 2 layers15 × 17 mm

- 2 layers10 × 51 mm

Similar boards
- 4 layers80 × 85 mm

Mainboard v13
DVA490-474-Project-Course/SSL-Hardware-Development
Contains all hardware related material. (No software).
118 partsMIT - 2 layers93.5 × 48.2 mm

SPACEDOS01
UniversalScientificTechnologies/SPACEDOS01
Silicon diode dosimeter optimized for spacecraft dosimetry
92 parts5GPL-3.0 - 4 layers90.9 × 50.3 mm

- 2 layers50 × 100 mm

Parrot imu
LucienMorey/parrot_imu
This design will host an IMU board for the Parody tripedal robotic platform. It will expose connect an IMU to the teensy 4.1 microcontroller with the ability to deliver this data over CAN bus and over an ethernet…
29 parts3MIT - 8 layers200 × 115 mm

- 4 layers100 × 67.8 mm

- 4 layers65 × 56 mm

I2S Hat
raptorlightning/I2S-Hat
An SPDIF Hat for the Raspberry Pi 2-X for SPDIF Communication
98 parts19GPL-3.0 - 2 layers99.1 × 40 mm

Questions
How big is the Base Station v3b PCB?
It measures 58 × 85 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Base Station v3b use?
130 parts, built around the STM32F767VIT6, 74LVC1G125DBV, DP83848CVV and SKY66112-11. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Base Station v3b KiCad files?
From the TIGERs-Mannheim/electronics repository on GitHub, at the commit this page was made from: the board is v2020/KiCad9/Base Station v3b/Base Station v3b.kicad_pcb and its schematic v2020/KiCad9/Ball Detection v4/Ball Detection v4.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Base Station v3b design in my own project?
Its repository states no licence, so its author keeps all rights: ask TIGERs-Mannheim before reusing the design.