Skip to the content
4 layers99.6 × 99.6 mmThemis tc2, the printed circuit board in 3D

Hardware and software for a direct-drive brushless DC motor and encoder.

Size
99.6 × 99.6 mm
Copper layers
4
Thickness
1.6 mm
Parts
109
Nets
63
Pads
273
Tracks, vias
363, 439
Pours
5
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
16 May 2025
Updated
22 Apr 2026

Overview

Themis tc2 is an open-source printed circuit board by thomabir, from the thomabir/themis-motor repository on GitHub. It is a 4-layer board of 99.6 × 99.6 mm with 109 parts on 63 nets, routed with 363 tracks and 439 vias.

It is built around the AD8130ARMZ-REEL, NE5532DR-MS and ADS131M03QPWRQ1, with the LT3097ADJC#PBF, MAX8887EZK33+T and C0805C102J5GACTU among its other parts. Its parts include 41 capacitors, 19 connectors, 14 resistors, 7 ICs and 4 diodes. It belongs with the robots and motor control boards of this library.

Main components

11

README

README.md

Themis Telescope Mount

Hardware and software for a direct-drive brushless DC motor and encoder for a telescope mount

Control Scheme

  • PWM
    • 50 to 100 kHz
    • Input: desired PWM duty cycle
    • Output: PWM signals to gate drivers
  • Inner Loop: Current Control (FOC)
    • Controls flux and torque currents.
    • Runs at 10–20 kHz.
    • Inputs: Torque target (from position control loop), Phase current measurements (from current sensor), rotor electrical angle (from encoder).
    • Outputs: PWM duty cycles via inverse Park/Clarke
  • Outer Loop: Position Control
    • Controls angular position and/or velocity, which is commanded from the observatory
    • Runs at 100–500 Hz.
    • Inputs: Position setpoint, measured position from encoder
    • Output: Torque command

Motor Specifications

  • Type: BLDC, direct drive (salvaged from a hoverboard)
  • Quantity: 2 motors
  • Electrical: 3 Phases, 30 Poles, 27 Slots, 36 V, 13 A RMS peak, 7A RMS continuous, 0.45 Ω, Y
  • Mechanical: ≈ 10 Nm continuous, ≈ 1.43 Nm/A, ≈ 16 rpm/V, 350 W (estimates, not necessarily accurate)

Encoder

DIY inductosyn, 0.05 arcseconds resolution, 1000 Hz sampling rate, custom SPI-like interface with absolute position, latency 1 ms.

System Requirements

  • Telescope Alt/Az axis control
  • Tracking speed: 1 rev / 24 hr
  • Slewing speed: 1 rev / 10 s
  • Tracking error: < 1 arcsecond RMS
  • Power: Mains
  • System inertia: Low (balanced 8" SCT)

Thermal: motor will be at low currents most of the time, so convection will probably be fine, with short peaks when slewing. (Motors are from a hoverboard, which was also only passively cooled)

Mechanical: Very low backlash; bearing friction (esp. static) likely to influence control scheme.

Parts

109
QtyValueFootprintReferences
13Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ1, J3, J5, J6, J7, J9, J10, J11, J13, J15, J17, J18, J19
1210uCapacitor_SMD:C_0805_2012MetricC1, C2, C3, C5, C6, C7, C9, C10, C12, C25, C30, C39
910nCapacitor_SMD:C_0805_2012MetricC11, C14, C15, C18, C23, C32, C33, C36, C38
91nCapacitor_SMD:C_0805_2012MetricC16, C19, C22, C26, C28, C29, C35, C37, C41
6100nCapacitor_SMD:C_0805_2012MetricC13, C17, C27, C31, C34, C40
61kResistor_SMD:R_0805_2012MetricR3, R4, R6, R11, R12, R14
5GNDTestPoint:TestPoint_Keystone_5010-5014_MultipurposeTP2, TP5, TP6, TP12, TP13
44.7kResistor_SMD:R_0805_2012MetricR7, R8, R9, R10
4BAT54Diode_SMD:D_SOD-323D1, D2, D3, D4
4MountingHoleMountingHole:MountingHole_3.2mm_M3_DIN965H1, H2, H3, H4
3Screw_Terminal_01x02TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-2_1x02_P2.54mm_HorizontalJ4, J8, J16
210kPotentiometer_THT:Potentiometer_Bourns_3296W_VerticalRV1, RV2
210kResistor_SMD:R_0805_2012MetricR5, R13
2120kResistor_SMD:R_0805_2012MetricR1, R2
21uCapacitor_SMD:C_0805_2012MetricC20, C21
24.7uCapacitor_SMD:C_0805_2012MetricC4, C8
2A1TestPoint:TestPoint_Keystone_5010-5014_MultipurposeTP8, TP15
2A2TestPoint:TestPoint_Keystone_5010-5014_MultipurposeTP9, TP16
2A3TestPoint:TestPoint_Keystone_5010-5014_MultipurposeTP10, TP17
2A4TestPoint:TestPoint_Keystone_5010-5014_MultipurposeTP7, TP14
2A5TestPoint:TestPoint_Keystone_5010-5014_MultipurposeTP11, TP18
2AD8130easyeda2kicad:SOIC-8_L4.9-W3.9-P1.27-LS6.0-BLU3, U6
2NE5532Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU4, U7
1+12VTestPoint:TestPoint_Keystone_5010-5014_MultipurposeTP1
1-12VTestPoint:TestPoint_Keystone_5010-5014_MultipurposeTP3
1220nCapacitor_SMD:C_0805_2012MetricC24
13.3VTestPoint:TestPoint_Keystone_5010-5014_MultipurposeTP4
1ADS131M03easyeda2kicad:TSSOP-20_L6.5-W4.4-P0.65-LS6.4-BLU5
1Conn_01x03_PinConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ14
1Conn_01x08_PinConnector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalJ12
1LT3097Snapeda:05-08-7071_ADIU1
1MAX8887Package_TO_SOT_SMD:SOT-23-5U2
1Screw_Terminal_01x03TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-3_1x03_P2.54mm_HorizontalJ2

More from thomabir/themis-motor

2
  • 2 layers100 × 100 mmThemis mc v3, the printed circuit board in 3D

    Themis mc v3

    thomabir/themis-motor

    Hardware and software for a direct-drive brushless DC motor and encoder.

    94 parts
  • 4 layers99.6 × 99.6 mmThemis tc1, the printed circuit board in 3D

    Themis tc1

    thomabir/themis-motor

    Hardware and software for a direct-drive brushless DC motor and encoder.

    69 parts

Similar boards

  • 2 layers157.5 × 72 mmNixie tube clock, the printed circuit board in 3D

    Nixie tube clock

    mbelanger0/nixie-tube-clock

    A nixie tube clock as a final PCB design project for ENGR3430: Eclectronics at Olin College of Engineering

    145 parts
  • 2 layers254 × 254 mmFin panel, the printed circuit board in 3D

    Fin panel

    Helios-Rocket/fin-strain-gauge

    188 parts1
  • 6 layers254 × 130 mmQuartz, the printed circuit board in 3D

    Quartz

    osprey-dcs/Quartz

    Quartz ADC PCB OSH repository

    1,244 parts
  • 4 layers100 × 106 mmDelivery robot 1, the printed circuit board in 3D

    Delivery robot 1

    ECE49022Team22/delivery-robot-pcb

    Delivery robot KiCad PCB project and reusable 3.3 V LDO module

    181 parts
  • 4 layers120 × 94 mmAlfred, the printed circuit board in 3D

    Alfred

    mkol-ME/A1-4RD

    Local voice assistant with a character: Whisper and a 26B LLM on a reflashed datacenter GPU, a custom voice, a 3D-printed body and a KiCad PCB

    125 partsMIT
  • 4 layers100 × 70 mmSEM, the printed circuit board in 3D

    SEM

    Serhio4522/SEM_hitachi-

    Digitization of a Hitachi scanning electron microscope (SEM) — hardware design, FPGA firmware, and analog frontend schematics.

    288 parts1
  • 4 layers250 × 140 mmThermocouple 8ch, the printed circuit board in 3D

    Thermocouple 8ch

    mahmoud-elghamry/thermocouple

    This directory is a self-contained KiCad 10 project. It does not share files with, and must not be confused with, the single-channel board in hardware/single-channel/.

    209 parts1
  • 4 layers243.8 × 171.5 mmNeotron Pico, the printed circuit board in 3D

    Neotron Pico

    Neotron-Compute/Neotron-Pico

    A Neotron powered by the Raspberry Pi Pico

    242 parts250

Questions

How big is the Themis tc2 PCB?

It measures 99.6 × 99.6 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Themis tc2 use?

109 parts, built around the AD8130ARMZ-REEL, NE5532DR-MS, ADS131M03QPWRQ1 and LT3097ADJC#PBF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Themis tc2 KiCad files?

From the thomabir/themis-motor repository on GitHub, at the commit this page was made from: the board is encoder-electronics/tc2/kicad/themis_tc2.kicad_pcb and its schematic encoder-electronics/tc1/kicad/themis_tc1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Themis tc2 design in my own project?

Its repository states no licence, so its author keeps all rights: ask thomabir before reusing the design.