Skip to the content
2 layers50.5 × 230.7 mmVco, the printed circuit board in 3D

A Voltage Contolled Oscillator (VCO) is the backbone module for subtractive synthesis. It generates an audio signal which can then be shaped by myriad filters and amplifiers. Without a VCO you don't have a synth.

Size
50.5 × 230.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
124
Nets
84
Pads
330
Tracks, vias
770, 44
Pours
2
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
15 Feb 2023
Updated
29 Mar 2025

Overview

Vco is an open-source printed circuit board by thismatters, from the thismatters/EurorackVco repository on GitHub. It is a 2-layer board of 50.5 × 230.7 mm with 124 parts on 84 nets, routed with 770 tracks and 44 vias.

It is built around the OPA2134UA, LM311 and MMBFJ113. Its parts include 51 resistors, 13 capacitors, 11 connectors, 8 diodes and 7 ICs. It belongs with the audio and music boards of this library.

Main components

3

README

README.md

Voltage Controlled Oscillator

A Voltage Contolled Oscillator (VCO) is the backbone module for subtractive synthesis. It generates an audio signal which can then be shaped by myriad filters and amplifiers. Without a VCO you don't have a synth.

The circuit here is based on the Yusynth VCO with minor tweaks to make it more Eurorack friendly. The changes I've made are thus:

  • Selected resistors appropriate for +/-12V rails,
  • Added polarity protection so that a backward power header doesn't fry anything (twin series schotty diodes: BAT54SL),
  • Selected a modern dual NPN diode package for the exponential converter,
  • Full surface mount design,
  • Toggle switch on front face for sync hardness.

The Yusynth page is a treasure trove of information about this circuit that I am too amateur to claim as my own; please read that outstanding page before using this circuit. The page provides several other implementations of the circuit that you may find suitable.

The KiCAD project here uses the library/footprints found in my companion repo.

Width

10hp on a standard 3U rack.

Inputs

This VCO features dual inputs for 1V/oct, Linear FM, and Exponential FM, Sync, and PWM. A toggle switch on the front face allows the player to set sync hardness. Two potentiometers allow the setting of frequency offset: coarse and fine. Two potentiometers are devoted to level for each of the frequency modulators (linear and exponential). Another pair of potentiometers gives control over (inherent) pulse width and PWM input level.

Outputs

Four wave shapes are simultaneously available:

  • Sine
  • Triangle
  • Saw (falling)
  • Square

Fiddly bits

Three 100kOhm resistors (R3, R4, R5) should be selected to within 0.1% tolerance (of each other) for good input tracking.

Likewise, two diodes (D5 and D6) ought to be selected which have a closely matched bias voltage in order to ensure a good sine wave symmetry. Testing SMD diodes for bias voltage is no small feat, so I didn't really bother doing this on my test circuits and first printed boards and they seemed fine. I hasten to bet that manufacturing processes have improved to the extent that manual matching is no longer relevant; but that could also just be a justification for laziness!

The schematic shows an OPA2134, however the original circuit calls for an OPA2137. The OPA2134 is a higher quality chip for sound applications, but it is also more expensive and was out of stock when I went to order; the OPA2137 is a suitable alternative.

The schematic calls for a thermally_coupled_transistor_pair; this is actually two components arranged carefully together. First a dual NPN transistor array (BCM847), then a thermco resistor which is nestled directly atop the transistor array package and the couple are blanketed in thermal grease so that the two components stay close to the same temperature.

Adjustment

You'll need an oscilloscope, a CV keyboard, and ideally a tuner.

Waveshape

  1. Set the frequency potentiometers to their middle positions, set the FM and PWM level knobs to minimum (counterclockwise), and the PW knob to the middle position.
  2. Connect the sawtooth output to the oscilloscope.
  3. Power on the circuit.
  4. Adjust RV10 until the sawtooth fills the full covers 10V from peak to peak (no horizontal line at top or bottom).
  5. Adjust RV9 until the sawtooth is centered about 0V. (You may have to revisit RV10 to get this perfect; before moving on the saw wave should fill the +/-5V range)
  6. Connect the triangle output to the oscilloscope.
  7. Adjust RV9 some more to get the triangle shape just right.
  8. Adjust RV11 until the triangle is centered around 0V. (You may have to revisit RV10 to get this perfect)
  9. Connect the sine output to the oscilloscope.
  10. The sine wave ought to look about right, but you may adjust RV9, RV11 (and possibly RV10) to hone this.

Volt/Octave Tracking

  1. Connect the CV source to the 1V/oct input, set the CV to 0V. If you're using a keyboard for this, hit C0.
  2. Connect your tuner to the sine output.
  3. Set CV to 0V, adjust the frequency knobs (coarse, then fine) until the tuner shows A1* (55Hz), then set the CV to 1V (press C1).
  4. If the tuner shows A2 (110Hz) then you're all set, move on to the next step. Otherwise, if the pitch is sharp (>110Hz) adjust RV8 so that the pitch goes sharper (if flat go flatter)! Now go back to the prior step.
  5. Repeat the prior two steps this time jumping an additional octave. Once you've worked through all the octaves you have available then you're done!
ToneFrequency
A155 Hz
A2110 Hz
A3220 Hz
A4440 Hz
A5880 Hz
A61760 Hz
A73520 Hz
A87040 Hz

* A1 was chosen because it has a nice round number for a frequency which makes it easy to dial in on an oscilloscope. If you have a tuner use whatever pitch you like.

Tuning

  1. Disconnect all inputs from circuit.
  2. Connect the tuner to the sine output.
  3. Set the coarse frequency knob to the fully counterclockwise position (0), set the fine frequency knob to the middle position (0).
  4. Connect a CV keyboard to the 1v/oct input, then press A3 (220Hz).
  5. Adjust RV6 until the frequency is 220Hz.

Vendors

There are part numbers in the BOM for many of the parts (not for basic passives though) at the following vendors:

  • Mouser: Needs no introduction. Get your ICs from here (or digikey).
  • Tayda Electronics: Good supplier for passive components; audio jacks, and potentiometers. Their audio jacks are slightly smaller than the thonkiconn from thonk.
  • Thonk: The only place I've found tempco resistors for sale! You're looking for the 1k resistor, their store doesn't support part number searches. These are apparently sold out forever and no longer manufactured... I'll look around for alternatives, and experiment with omitting that resistor...
  • Love My Switches: Has really good knobs to go on those potentiometers!
  • OSHPark: Fast and (relatively) cheap PCB manufacturer. The V1 circuit works great, but you may have a hard time finding the 1K thermco resistor.

Changelog

v1

  • first draft

v2

  • Added polarity protection,
  • bigger holes for toggle switch footprint,
  • reorganized board for easier trace routing,
  • updated design language,
  • narrowed by 2hp,
  • changed some resistor values for more consistent +/-5V output,

Parts

124
QtyValueFootprintReferences
13100KResistor_SMD:R_0805_2012MetricR3, R4, R5, R15, R16, R20, R23, R30, R32, R35, R36, R37, R41
610KResistor_SMD:R_0805_2012MetricR21, R24, R28, R29, R33, R39
61N4148Diode_SMD:D_SOD-323_HandSolderingD1, D2, D3, D4, D5, D6
6B100KEurorack:Potentiometer_RV16AF-41-15R1RV1, RV2, RV3, RV4, RV5, RV7
5100nCapacitor_SMD:C_0805_2012MetricC6, C7, C8, C9, C10
41KResistor_SMD:R_0805_2012MetricR43, R44, R46, R51
4MountingHoleEurorack:Mech-MountingHoleH17, H18, H19, H20
31MResistor_SMD:R_0805_2012MetricR17, R19, R26
322KResistor_SMD:R_0805_2012MetricR18, R22, R48
347KResistor_SMD:R_0805_2012MetricR2, R10, R38
347pCapacitor_SMD:C_0805_2012MetricC1, C11, C13
210Resistor_SMD:R_0805_2012MetricR12, R13
2100KPotentiometer_THT:Potentiometer_Bourns_3296W_VerticalRV9, RV10
2150KResistor_SMD:R_0805_2012MetricR42, R47
2180KResistor_SMD:R_0805_2012MetricR31, R45
21V/OCTEurorack:AudioJack2_Tayda_A-2566J2, J3
21v/octEurorack:Mech-AudioJack-Hole-Input-VoctH1, H2
2220KResistor_SMD:R_0805_2012MetricR7, R27
222u 50VCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC2, C3
227KResistor_SMD:R_0805_2012MetricR9, R14
233KResistor_SMD:R_0805_2012MetricR11, R25
2470KResistor_SMD:R_0805_2012MetricR8, R34
2D_Dual_Series_AKCPackage_TO_SOT_SMD:SOT-23D7, D8
2TL074Package_SO:SOIC-14_3.9x8.7mm_P1.27mmU1, U6
11.2KResistor_SMD:R_0805_2012MetricR49
1100pCapacitor_SMD:C_0805_2012MetricC4
110pCapacitor_SMD:C_0805_2012MetricC12
115KResistor_SMD:R_0805_2012MetricR50
1220pCapacitor_SMD:C_0805_2012MetricC5
1250KPotentiometer_THT:Potentiometer_Bourns_3296W_VerticalRV6
125KPotentiometer_THT:Potentiometer_Bourns_3296W_VerticalRV8
13M3Resistor_SMD:R_0805_2012MetricR6
150KPotentiometer_THT:Potentiometer_Bourns_3296W_VerticalRV11
168KResistor_SMD:R_0805_2012MetricR1
18.2KResistor_SMD:R_0805_2012MetricR40
1Conn_02x05_Odd_EvenEurorack:PinHeader_2x05_P2.54mm_VerticalJ11
1EXP FMEurorack:AudioJack2_Tayda_A-2566J1
1L78L12_SO8Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU3
1L79L12_SO8Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU4
1LIN FMEurorack:AudioJack2_Tayda_A-2566J4
1LM311Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU7
1MMBFJ113Package_TO_SOT_SMD:SOT-23Q1
1OPA2134Package_SO:SO-8_3.9x4.9mm_P1.27mmU2
1PWMEurorack:AudioJack2_Tayda_A-2566J5
1SYNCEurorack:AudioJack2_Tayda_A-2566J6
1SineEurorack:AudioJack2_Tayda_A-2566J7
1SquareEurorack:AudioJack2_Tayda_A-2566J10
1Sync ModeEurorack:Switch_SPDT_Tayda_A-5751SW1
1TriangleEurorack:AudioJack2_Tayda_A-2566J9
1exp fmEurorack:Mech-Potentiometer-Hole_levelH14
1exp fmEurorack:Mech-AudioJack-Hole-Input-CVH3
1fine tuneEurorack:Mech-Potentiometer-Hole_panH12
1frequencyEurorack:Mech-Potentiometer-Hole_levelH11
1lin fmEurorack:Mech-AudioJack-Hole-Input-CVH4
1lin fmEurorack:Mech-Potentiometer-Hole_levelH13
1lockedEurorack:AudioJack2_Tayda_A-2566J8
1pwEurorack:Mech-Potentiometer-Hole_panH15
1pwmEurorack:Mech-AudioJack-Hole-Input-CVH5
1pwm lvlEurorack:Mech-Potentiometer-Hole_levelH16
1sawEurorack:Mech-AudioJack-Hole-OutputH9
1sineEurorack:Mech-AudioJack-Hole-OutputH7
1squareEurorack:Mech-AudioJack-Hole-OutputH10
1syncEurorack:Mech-AudioJack-Hole-Input-ClockH6
1sync hardnessEurorack:Mech-2M_Switch-HoleH21
1thermally_coupled_transistor_pairEurorack:SOT457+thermco_resistorU5
1triangleEurorack:Mech-AudioJack-Hole-OutputH8

Similar boards

  • 2 layers365.8 × 254 mmRaemixx500, the printed circuit board in 3D

    Raemixx500

    SukkoPera/Raemixx500

    Open Hardware Remake of the Commodore Amiga 500+ Mainboard

    372 parts316
  • 4 layers223 × 95 mmAnalog i, the printed circuit board in 3D

    Analog i

    deimoscontrols/deimos

    Realtime data acquisition and controls ecosystem, including hardware, firmware, and software.

    568 parts44
  • 2 layers75 × 90 mmC3lingo unit channel mixer, the printed circuit board in 3D

    C3lingo unit channel mixer

    c3lingo/c3lingo-interpreter-unit

    A customized audio mixer and personal monitoring console for simultaneous interpreters.

    103 parts7CC-BY-SA-4.0
  • 2 layers66 × 99.1 mmEsr meter, the printed circuit board in 3D

    Esr meter

    vpatkov/esr-meter

    AC ohmmeter

    105 parts5
  • 4 layers40.5 × 100 mmVcafd, the printed circuit board in 3D

    Vcafd

    GuavTek/ACID_VCA

    A eurorack VCA with a wavefolder and drive/clipping

    223 parts1CERN-OHL-W-2.0
  • 2 layers43.8 × 31.8 mmCba, the printed circuit board in 3D

    Cba

    0x007E/cba

    CAN-Bus Analog

    68 parts
  • 2 layers43.8 × 31.8 mmCbi, the printed circuit board in 3D

    Cbi

    0x007E/cbi

    CAN-Bus Input

    87 parts
  • 2 layers43.8 × 31.8 mmCbo, the printed circuit board in 3D

    Cbo

    0x007E/cbo

    CAN-Bus Output

    82 parts

Questions

How big is the Vco PCB?

It measures 50.5 × 230.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Vco use?

124 parts, built around the OPA2134UA, LM311 and MMBFJ113. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Vco KiCad files?

From the thismatters/EurorackVco repository on GitHub, at the commit this page was made from: the board is vco.kicad_pcb and its schematic vco.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Vco design in my own project?

Its repository states no licence, so its author keeps all rights: ask thismatters before reusing the design.