Skip to the content
2 layers172 × 98 mmMIDI Keyboard, the printed circuit board in 3D

A board to create my own beats, to make it mine, I will add my own doodles.

Size
172 × 98 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
23
Pads
76
Tracks, vias
171, 2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
19 Oct 2026
Updated
25 Oct 2026

Overview

MIDI Keyboard is an open-source printed circuit board by TheTank87, from the TheTank87/MIDI-Keyboard repository on GitHub. It is a 2-layer board of 172 × 98 mm with 14 parts on 23 nets, routed with 171 tracks and 2 vias.

It is built around the SK6812MINI-E. Its parts include 4 switches, 3 diodes, 1 IC and 1 connector. It belongs with the audio and music and keyboards and input boards and the ESP32 boards of this library.

Main components

1

README

README.md

MIDI-Keyboard

A board to create my own beats, to make it mine, I will add my own doodles. Screenshot 2026-10-24 at 4 33 40 PM

This is the MIDI Keyboard. It is a small hand-held device that creates musical sounds in the right hands. It uses capacitative touch keys, buttons, switches, and a rotary knob. It also includes SK6812 MINI-E Neopixels that light up whenever I press those keyboard buttons. It also includes that USB plugin brain thing from the Starbie, but this time it's a little bit more powerful, featuring the waveshare.

Features

  • EC11 Rotary Encoders
  • SK6812 MINI-E Neopixels
  • Bourns Slide Potentiometers
  • Kailh Choc Low-Profile Switches

BOM

DesignatorFootprintQuantityValueTotal CostLinks
D1, D2, D3LED_SK6812MINI-E_3.2x2.8mm_P1.5mm_ReverseMount3SK6812MINI-E$3.36Link
J1Capacitative Keys1Capacitative Touch Buttons
RV1, RV2Potentiometer_Bourns_PTA1543_Single_Slide2Slider$3.16Link
SW1, SW2, SW3Kailh Choc Low-Profile Switches3SW_Push$6.04Link
SW4RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm1RotaryEncoder_Switch_MP$1.44Link
U1Waveshare ESP32-S3-Zero1Waveshare ESP32-S3-ZERO$6.62Link
Total Parts Cost$17.46
Total Digikey Cost-Not using fast shipping$8.67
Total JLCPCB$12.20
Total Cost$38.33

Process:

Screenshot 2026-10-23 at 12 02 36 PM

I started with the schematic design of my PCB and wired up everything using the guide as reference. However, I did make a mistake of accidentally swapping the TX and RX ports so I fixed that asap. Screenshot 2026-10-23 at 4 56 44 PM

After that as fixed, I then went into the PCB editor and created my first design. Screenshot 2026-10-23 at 11 55 53 AM

However, there was a major flaw in this design, that is, the wiring of the waveshare was not efficient and the entire layout was doomed to be messy. So I had to go back the schematic editor and redo the wiring so that it fits with a better layout. Screenshot 2026-10-24 at 4 33 40 PM

As one can see, everything now wires up more cleanly. Insert crying-relief emoji...

Adding 3D Models and Decorations

3DRenderFrontWeek3

I got the 3D models from the guide repo, and everything was pretty straight forward. It was pretty easy to figure out that you need to align the ports from the 3D model through the holes in the PCB. There was a mishap with the rotary encoder where rotating the x and z produced same side rotations which was not supposed to happen. So I had to restart kicad.

I then decided to add some silkscreen to my builds. Silkscreen

Firmware & Other Additions

I also needed the circuit python for my board, so I went and downloaded the code.py and made changes to where the pins were wired so that it fits my board schematic. It turns out that I didn't need Ardunio IDE for this one as it's just using notepad and turning it into a .py file.

From past experiences, I also needed to add a whole lot more files not listed in the guide checklist on the HalfLife website. Which includes all my PCB files, the .pro file, and either a .cpl or .csv listing out all the positions of the components. I then reorganized the repo into folders.

Parts

14
QtyValueFootprintReferences
3SK6812MINI-ELED_SMD:LED_SK6812MINI-E_3.2x2.8mm_P1.5mm_ReverseMountD1, D2, D3
3SW_PushHackclub Footprints:Kailh Choc Low-Profile SwitchesSW1, SW2, SW3
2SliderPotentiometer_THT:Potentiometer_Bourns_PTA1543_Single_SlideRV1, RV2
1Conn_01x07Tank's Library-Capacitative Keys:Capacitative KeysJ1
1LOGOGraphics:Silkscreen2G***
1LOGOGraphics:SilkscreenB1G***
1LOGOGraphics:Silkscreen1G***
1RotaryEncoder_Switch_MPRotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mmSW4
1Waveshare ESP32-S3-ZEROHackclub Footprints:Waveshare ESP32-S3-ZeroU1

Similar boards

  • 4 layers234 × 84 mmMain panel, the printed circuit board in 3D

    Main panel

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    234 parts3kApache-2.0
  • 4 layers180.8 × 300.3 mmDilemma, the printed circuit board in 3D

    Dilemma

    Bastardkb/Dilemma

    The Dilemma is a vertical stagger low-profile keyboard with mods.

    383 parts590
  • 4 layers48 × 32 mmFlatSat, the printed circuit board in 3D

    FlatSat

    Pwnsat/FlatSat

    Flatsat v1.0 is a hardware based platform for aerospace cybersecurity research

    106 parts575GPL-2.0
  • 2 layersDemo, the printed circuit board in 3D

    Demo

    adamws/kicad-kbplacer

    KiCad plugin for automatic keyboard's key placement and routing

    48 parts547GPL-3.0
  • 2 layers97 × 78.5 mmDumbpad, the printed circuit board in 3D

    Dumbpad

    imchipwood/dumbpad

    Simple 4x4 numpad with rotary encoder. Powered by QMK via ATmega32u4 Pro Micro

    62 parts517GPL-2.0
  • 4 layers82.5 × 39.4 mmV4head, the printed circuit board in 3D

    V4head

    makerforgetech/modular-biped

    An open source framework for creating a bipedal modular companion robot.

    26 parts493GPL-3.0
  • 2 layers115.7 × 95.7 mmFifi split keeb, the printed circuit board in 3D

    Fifi split keeb

    raychengy/fifi_split_keeb

    Fifi Keyboard 🐶 ⌨️

    66 parts334
  • 4 layers70 × 54 mmPicoLab, the printed circuit board in 3D

    PicoLab

    CoretechR/PicoLab

    Web-GUI Embedded Multitool

    285 parts327GPL-3.0

Questions

How big is the MIDI Keyboard PCB?

It measures 172 × 98 mm and has 2 copper layers, 1.6 mm thick.

What parts does the MIDI Keyboard use?

14 parts, built around the SK6812MINI-E. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MIDI Keyboard KiCad files?

From the TheTank87/MIDI-Keyboard repository on GitHub, at the commit this page was made from: the board is PCB/MIDIKeyboard.kicad_pcb and its schematic PCB/MIDIKeyboard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the MIDI Keyboard design in my own project?

Its repository states no licence, so its author keeps all rights: ask TheTank87 before reusing the design.