2 layers72 × 66 mm
6 layers72 × 44 mm
Nes shell
TheBadZhang/nes_shell1NES 掌上游戏机，也不只是游戏机
- Size
- 72 × 44 mm
- Copper layers
- 6
- Thickness
- 1.6 mm
- Parts
- 62
- Nets
- 399
- Pads
- 684
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 29 Feb 2024
- Updated
- 14 Apr 2024
Overview
Nes shell is an open-source printed circuit board by TheBadZhang, from the TheBadZhang/nes_shell repository on GitHub. It is a 6-layer board of 72 × 44 mm with 62 parts on 399 nets.
It is built around the CH343P, USB3300-EZK and W25Q32JVZPIQ, with the CH334P, MPU-9250 and MT48LC16M16A2TG among its other parts. Its parts include 29 capacitors, 9 ICs, 8 connectors, 3 crystals and 2 resistors. It belongs with the retro computing and games boards and the STM32 boards of this library.
Main components
8
CH343P
TQFN-16-EP(3x3)-40℃~+85℃ 3.3V、5V 3mA 6Mbps 90uA USB 2.0 USB to UART TQFN-16-EP(3x3) USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB Converters
USB3300-EZK
QFN-32-EP(5x5)-40℃~+85℃ 3V~3.6V 54.7mA 83uA Controller USB 2.0 QFN-32-EP(5x5) USB Converters ROHSMicrochip TechnologyUSB Converters
W25Q32JVZPIQ
WSON-8-EP(5x6)-40℃~+85℃ 100,000 cycles 10uA 133MHz 2.7V~3.6V 20 Years 32Mbit 3ms SPI WSON-8-EP(5x6) NOR FLASH ROHSWinbondNOR FLASH
CH334P
QFN-16(3x3)-40℃~+85℃ 0.4mA 3.3V 4 480Mbps 85mA Hub USB 2.0 QFN-16(3x3) USB HUB Controllers ROHSWCH (Nanjing Qinheng Microelectronics)USB HUB Controllers
MPU-9250
QFN-24-EP(3x3)-40℃~+85℃ 2.4V~3.6V 8uA IMU (accelerometer + gyroscope) Motion event detection SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(3x3) Accelerometers ROHSTDK InvenSenseAccelerometers
MT48LC16M16A2TG
TSOP-54TSOP-54 DRAM ROHSMicron TechDRAM
RT9193-33GB
SOT-23-5-40℃~+125℃@(Tj) -50dB@(10kHz) 1 100uVrms 220mV@(300mA) 3.3V 300mA 5.5V 90uA Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSRICHTEKVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
ESD9B3.3ST5G
SOD-923(0402)ESD And Surge Protection (TVS/ESD)TECH PUBLIC
README
readme.md掌上 NES 游戏机
也不只是游戏机
基于 STM32H7B0VBT6 设计的 NES 掌上游戏机
包含 ESP8684 组成的 wifi 蓝牙 扩展 STM32G431CBU6 的可编程输入控制
本项目基于 weact stm32h7b0 开发板而来，主要用于学习 stm32h7b0 的使用。 移植了大量的有趣的程序，包括但不限于：
贪吃蛇、汉诺塔、俄罗斯方块
一些动画
ui效果
按键驱动
音频采集与输出
Parts
62| Qty | Value | Footprint | References |
|---|---|---|---|
| 21 | 0.1uF | Capacitor_SMD:C_0201_0603Metric | C10, C11, C12, C13, C14, C15, C16, C17, C19, C20, C21, C22, C23, C24, C25, C26 +5 |
| 5 | Conn_02x06_Odd_Even | Connector_PinSocket_1.27mm:PinSocket_2x06_P1.27mm_Vertical_SMD | J3, J4, J5, J6, J7 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 2 | 1.5pF | Capacitor_SMD:C_0402_1005Metric | C5, C18 |
| 2 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C96, C99 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric | R29, R30 |
| 2 | 8pF | Capacitor_SMD:C_0402_1005Metric | C6, C7 |
| 2 | Conn_01x20_MountingPin | Connector_FFC-FPC:TE_2-1734839-0_1x20-1MP_P0.5mm_Horizontal | J1, J2 |
| 2 | ESD9B3.3ST5G | Diode_SMD:D_SOD-923 | D4, D5 |
| 1 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C97 |
| 1 | 12M | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm | Y4 |
| 1 | 22nF | Capacitor_SMD:C_0402_1005Metric | C98 |
| 1 | CH334P | Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm_ThermalVias | U13 |
| 1 | CH343P | Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm_ThermalVias | U18 |
| 1 | Crystal | Crystal:Crystal_SMD_2012-2Pin_2.0x1.2mm | Y2 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm | Y1 |
| 1 | DMU | TestPoint:TestPoint_Pad_D1.0mm | TP7 |
| 1 | DPU | TestPoint:TestPoint_Pad_D1.0mm | TP8 |
| 1 | M0S | my_chips:M0S | U5 |
| 1 | MPU-9250 | Sensor_Motion:InvenSense_QFN-24_3x3mm_P0.4mm | U17 |
| 1 | MT48LC16M16A2TG | Package_SO:TSOP-II-54_22.2x10.16mm_P0.8mm | U16 |
| 1 | RT9193-33GB | Package_TO_SOT_SMD:SOT-23-5 | U19 |
| 1 | STM32H7B0IBKxQ | Package_BGA:UFBGA-201_10x10mm_Layout15x15_P0.65mm | U1 |
| 1 | SW_Push | my_footprint:KEY-SMD_4P-L4.2-W3.4-P2.15-LS4.5-TL | SW3 |
| 1 | USB3300-EZK | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm | U20 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J10 |
| 1 | W25Q32JVZP | Package_SON:WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4.3mm | U15 |
| 1 | hub_gnd | TestPoint:TestPoint_Pad_D1.0mm | TP6 |
| 1 | hub_ldo_3v3 | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
Questions
How big is the Nes shell PCB?
It measures 72 × 44 mm and has 6 copper layers, 1.6 mm thick.
What parts does the Nes shell use?
62 parts, built around the CH343P, USB3300-EZK, W25Q32JVZPIQ and CH334P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Nes shell KiCad files?
From the TheBadZhang/nes_shell repository on GitHub, at the commit this page was made from: the board is hardware/nes_shell/nes_shell.kicad_pcb and its schematic hardware/key_board/key_board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Nes shell design in my own project?
Its repository states no licence, so its author keeps all rights: ask TheBadZhang before reusing the design.
More from TheBadZhang/nes_shell
4- 2 layers72 × 66 mm
- 2 layers72 × 44 mm
- 2 layers84.7 × 15.9 mm
Similar boards
- 2 layers110 × 67 mm
- 4 layers68.6 × 53.3 mm
- 4 layers310 × 123 mm
- 2 layers33.2 × 40 mm
- 4 layers81 × 80.9 mm
- 4 layers100 × 100 mm
- 2 layers
- 2 layers44 × 44 mm
