Skip to the content
4 layers38.3 × 25.1 mmBLE sensors, the printed circuit board in 3D

PCB and embedded hardware projects by Athanasios Vasiloglou, Embedded Systems & Hardware Engineer.

Size
38.3 × 25.1 mm
Copper layers
4
Thickness
1.6 mm
Parts
51
Nets
62
Pads
221
Tracks, vias
438, 76
Pours
4
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
24 Sep 2026
Updated
24 Sep 2026

Overview

BLE sensors is an open-source printed circuit board by thanvas81, from the thanvas81/hardware-portfolio repository on GitHub. It is a 4-layer board of 38.3 × 25.1 mm with 51 parts on 62 nets, routed with 438 tracks and 76 vias.

It is built around the MCP73871EV, BME280 and TPS63031DSK, with the PRTR5V0U2X among its other parts. Its parts include 21 resistors, 16 capacitors, 6 ICs, 4 diodes and 3 connectors. It belongs with the radio and wireless and sensors and measurement boards of this library.

Main components

4

README

README.md

Hardware Portfolio

PCB and embedded hardware projects by Athanasios Vasiloglou, Embedded Systems & Hardware Engineer.

Each project has 3D renders, schematics, layer views where available, and a write-up of the design. Projects are listed from most to least complex.

At a glance

#ProjectAreaBoardKey parts
1Industrial Controller / GatewayIndustrial control4-layer · 340 × 147 mm · 486 partsSTM32H743, KSZ8863 Ethernet switch, isolated RS-485, mains AC/DC
2Linux SoM Carrier BoardIndustrial IoT4-layer · 167 × 100 mm · 274 partsi.MX 91 SoM, EC25 LTE, Ethernet, RS-485, CAN
3Handheld High-Irradiance LED ControllerPower electronics3 boards · AltiumUSB-C PD, 2S charger, 4-switch buck-boost, nRF52840
4GPS/GSM Tracker (Rev 3)IoT & tracking4-layer · 65 × 94 mm · 192 partsSTM32U575, LTE Cat-1, NEO-M9N GNSS
5BLE Channel Sounding Sensor BoardWireless / thesis4-layer · 38 × 25 mmnRF54L15, Channel Sounding, 17 cm mean error
6Vehicle I/O Validator (Rev 2)Automotive test4-layer · 142 × 72 mm · 232 partsSTM32U545, 20 protected inputs, USB-C
7Compact LTE-M / NB-IoT TrackerIoT & tracking4-layer · 49 × 53 mm · 89 partsBG96, STM32U545, Li-ion charger
8Control Unit Tester (Rev 2)Automotive test4-layer · 194 × 52 mm · 236 partsWindow comparators, 20 switched outputs
9RP2040 Diagnostic Tester (Rev 2)Test tools2-layer · 69 × 54 mmRaspberry Pi Pico, UART sniffer, 24 V input
10CANLink ModuleExpansion module2-layer · 65 × 64 mmPIC18 CAN controller, TCAN3413
11Relay & Analog Input Expansion BoardExpansion module2-layer · 65 × 38 mmTX2 relay, LMV324 analog front end

Featured projects

Industrial Controller / Gateway

Industrial Controller / Gateway

Mains-powered controller bridging a managed Ethernet switch to 24 V field I/O.

  • STM32H743, KSZ8863 2-port Ethernet switch
  • 2× isolated RS-485, 4–20 mA, PT100, opto inputs, relays, smart high-side outputs
  • On-board 90 W AC/DC, four isolation domains, mains relay channel
  • 4-layer, 340 × 147 mm, 486 components

STM32H7 Ethernet Isolation Mains KiCad



Linux SoM Carrier Board

Linux SoM Carrier Board

Industrial IoT carrier for an NXP i.MX 91 Linux SoM. Full design and bring-up.

  • Quectel EC25 LTE (mini-PCIe), dual SIM
  • Ethernet, RS-485, CAN, USB-C, digital I/O, RTC, tamper input
  • Wide-input supply, Li-ion backup with power-path
  • 4-layer, 167 × 100 mm, 274 components

i.MX 91 Embedded Linux LTE KiCad Industrial IoT



Handheld High-Irradiance LED Controller

Handheld High-Irradiance LED Controller

Battery-powered controller for a high-power red LED array. Freelance design across three boards.

  • USB-C PD input, 2S Li-ion charger with power-path
  • 4-switch buck-boost LED rail, 7 constant-current channels
  • nRF52840 Bluetooth LE, IR temperature sensing, fan control

Altium USB-C PD Power electronics nRF52840 LED drivers



GPS/GSM Tracker

GPS/GSM Tracker

LTE Cat-1 + GNSS vehicle tracker, Rev 3 redesigned in KiCad for production.

  • STM32U575 low-power MCU, SIMCom A7672 LTE modem, u-blox NEO-M9N GNSS
  • Li-ion charger with power-path, wide-input buck, backup cell
  • 4-layer, 65 × 94 mm, 192 components

STM32U5 LTE Cat-1 GNSS KiCad 4-layer



BLE Channel Sounding Sensor Board

BLE Channel Sounding Sensor Board

Custom nRF54L15 board for sub-metre indoor positioning with Bluetooth Channel Sounding. NTUA diploma thesis.

  • 17 cm mean ranging error across three anchors
  • 4-layer, 38 × 25 mm PCB in KiCad
  • Accelerometer + magnetometer, temperature / humidity / pressure
  • USB-C or Li-ion, with charger and buck-boost

nRF54L15 Zephyr KiCad BLE Channel Sounding



Vehicle I/O Validator

Vehicle I/O Validator

Test tool that monitors 20 vehicle I/O lines and reports them to a PC over USB.

  • 20 protected inputs with red / blue status LEDs per channel
  • STM32U545, USB-C, 60 V buck from the vehicle supply
  • 4-layer, 142 × 72 mm, 232 components

STM32U5 Automotive Test equipment KiCad



Compact LTE-M / NB-IoT Tracker

Compact LTE-M / NB-IoT Tracker

Small battery-backed asset tracker.

  • Quectel BG96 (LTE-M / NB-IoT + GNSS), STM32U545
  • Accelerometer wake-up, NOR flash logging
  • Li-ion charger, wide-input buck, switched modem rail
  • 4-layer, 49 × 53 mm, 89 components

STM32U5 LTE-M NB-IoT GNSS KiCad



Control Unit Tester

Control Unit Tester

Stand-alone, fully analog bench tester for vehicle control units.

  • 16 inputs with window-comparator status LEDs
  • 20 outputs, each switchable to +Vin / open / GND
  • 60 V buck from the vehicle supply, no MCU needed
  • 4-layer, 194 × 52 mm, 236 components

Analog Automotive Test equipment KiCad



More boards

RP2040 Diagnostic Tester
RP2040 Diagnostic Tester
Raspberry Pi Pico field tool that talks to and sniffs UART links on 24 V equipment, with LCD and buttons
CANLink Module
CANLink Module
Plug-in CAN ↔ UART bridge: PIC18 with on-chip CAN controller and TI TCAN3413 transceiver
Relay and Analog Input Expansion Board
Relay & Analog Input Expansion Board
Stack-on board with a relay output and protected, buffered analog inputs

LinkedIn · GitHub profile

Designs are shown for portfolio purposes only. Projects built for employers and clients are presented without source files, and are not licensed for reuse.

Parts

51
QtyValueFootprintReferences
80.1uCapacitor_SMD:C_0603_1608MetricC1, C2, C3, C4, C6, C11, C14, C16
510kResistor_SMD:R_0603_1608MetricR17, R18, R19, R21, TH1
410uCapacitor_SMD:C_0805_2012MetricC5, C10, C12, C13
3470RResistor_SMD:R_0603_1608MetricR5, R6, R7
3LEDLED_SMD:LED_0603_1608MetricD1, D2, D3
2100RResistor_SMD:R_0603_1608MetricR15, R16
2100kResistor_SMD:R_0603_1608MetricR10, R14
222RResistor_SMD:R_0603_1608MetricR8, R9
24.7kResistor_SMD:R_0603_1608MetricR1, R2
24.7uCapacitor_SMD:C_0603_1608MetricC7, C8
25.11kResistor_SMD:R_0603_1608MetricR11, R12
11.5uInductor_SMD:L_1210_3225MetricL1
110uCapacitor_SMD:C_0603_1608MetricC9
11MResistor_SMD:R_0603_1608MetricR13
14.7uCapacitor_SMD:C_0805_2012MetricC17
1BME280Package_LGA:Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumberingU1
1Conn_01x02Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_VerticalJ2
1Conn_ARM_SWD_TagConnect_TC2030-NLConnector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_VerticalJ1
1LSM303AHTRMy_Libraries:LSM303AHTRU2
1MCP2221AxSTPackage_SO:TSSOP-14_4.4x5mm_P0.65mmU7
1MCP73871Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mmU5
1ME54BS01My_Libraries:ME54BS01U4
1PRTR5V0U2XPackage_TO_SOT_SMD:SOT-143D4
1Rprog1Resistor_SMD:R_0603_1608MetricR3
1Rprog3Resistor_SMD:R_0603_1608MetricR4
1TPS63031DSKPackage_SON:WSON-10-1EP_2.5x2.5mm_P0.5mm_EP1.2x2mmU3
1USB_C_ReceptacleConnector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASVJ3

Similar boards

  • 4 layers60 × 60 mmRocket payload, the printed circuit board in 3D

    Rocket payload

    Gupatron/Gupsfirstpcb

    This is the first pcb that I will manufacture and intend to use for teleop usecases in my personal projects.

    138 parts
  • 2 layers43 × 93 mmLoRaNode, the printed circuit board in 3D

    LoRaNode

    cernohorsky/LoRa-Node-Solar

    LoRa Node based on Arduino Pro mini with RFM95W module and PCB antenna. Includes TPS63031 buck-boost convertor and MCP7381 LiPo charger prepared for solar panel. PCB has I2C pinheader and few GPIO pads.

    59 parts3
  • 4 layers29.5 × 36.1 mmKeyboard, the printed circuit board in 3D

    Keyboard

    anhenaobe/nrf52840-modular-wireless-som

    Reusable four-layer nRF52840 wireless SoM with BLE, USB-C, LiPo charging, buck-boost power management, RF antenna integration, and manufacturing-ready outputs.

    76 partsGPL-3.0
  • 4 layers68 × 100 mmPocket caddy, the printed circuit board in 3D

    Pocket caddy

    bkuhn4/golf-gps

    The Pocket Caddy hardware is built around the ESP32-C3 microcontroller and includes the following components:

    90 parts
  • 4 layers74.4 × 64.2 mmIot device pcb, the printed circuit board in 3D

    Iot device pcb

    ODARI-CHARLES1/iot_device_pcb

    Hardware design for a air conditioner pcb design using Kicad software. This is for learning purpose only not manufacturable.

    76 parts2
  • 4 layers89 × 54.5 mmESP32 sensor board, the printed circuit board in 3D

    ESP32 sensor board

    andreschaparro/udemy-advanced-pcb-design-with-kicad-9

    93 parts1
  • 4 layers101.3 × 50.5 mmESP32 sensor board, the printed circuit board in 3D

    ESP32 sensor board

    Ankithkumarsingh/ESP32-custom-sensor-board

    This PCB contains the power supply unit, ESP32 module as compute, microphone sensor, light sensing sensor, SDCard module for data logging.

    94 parts1
  • 4 layers96.5 × 54.4 mmESP32-IoT, the printed circuit board in 3D

    ESP32-IoT

    ddennis18/ESP32-IoT-DevBoard

    An ESP32-C3 based IoT controller board designed in KiCad. The board combines wireless control, sensor interfaces, local storage, audio/light sensing, USB connectivity, and single-cell Li-ion battery support on a compact…

    88 parts1MIT

Questions

How big is the BLE sensors PCB?

It measures 38.3 × 25.1 mm and has 4 copper layers, 1.6 mm thick.

What parts does the BLE sensors use?

51 parts, built around the MCP73871EV, BME280, TPS63031DSK and PRTR5V0U2X. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the BLE sensors KiCad files?

From the thanvas81/hardware-portfolio repository on GitHub, at the commit this page was made from: the board is ble-channel-sounding-board/kicad/BLE_sensors.kicad_pcb and its schematic ble-channel-sounding-board/kicad/Accelerometer-Magnetometer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the BLE sensors design in my own project?

Its repository states no licence, so its author keeps all rights: ask thanvas81 before reusing the design.