
Iot risk logger stm32l4
polesskiy-dev/iot-risk-logger-stm32l4
Open IoT risk data logger based on STM32L4 MCU

The Pocket Caddy hardware is built around the ESP32-C3 microcontroller and includes the following components:
Pocket caddy is an open-source printed circuit board by bkuhn4, from the bkuhn4/golf-gps repository on GitHub. It is a 4-layer board of 68 × 100 mm with 90 parts on 71 nets, routed with 481 tracks and 233 vias.
It is built around the ESP32-C3-WROOM-02-H4, MCP73871EV and NEO-M9N-00B, with the SHT30-DIS, TPS63031DSKR and BQ27411DRZT-G1A among its other parts. Its parts include 25 resistors, 23 capacitors, 7 diodes, 6 ICs and 5 switches. It belongs with the ESP32 and RISC-V boards of this library.
Pocket Caddy is a handheld golf GPS and shot tracking device designed to help golfers track their performance and environmental conditions. It utilizes a high-precision u-blox GNSS module to measure shot distances and logs them to a micro SD card along with real-time temperature and humidity data. The device features an OLED display for easy navigation, a battery fuel gauge for power management, and a robust menu system for managing user profiles and reviewing shot history.
The Pocket Caddy hardware is built around the ESP32-C3 microcontroller and includes the following components:
| Component | Pin Name | ESP32-C3 Pin |
|---|---|---|
| Buttons | Button 1 (Down) | GPIO 9 |
| Button 2 (Up) | GPIO 20 | |
| Button 3 (Select) | GPIO 2 | |
| I2C Bus | SDA | GPIO 10 |
| SCL | GPIO 4 | |
| GPS | Enable | GPIO 3 |
| Reset | GPIO 21 |
To compile the firmware, you will need to install the following libraries via the Arduino Library Manager:
When programming the device for the first time (or if it becomes unresponsive), you need to manually enter the bootloader mode:
To ensure the device communicates correctly over USB for serial monitoring and subsequent uploads:
Tools > Board > Boards Manager and search "esp32".Tools > Board > esp32 > ESP32C3 Dev Module.Tools > USB CDC On Boot > Enabled.Tools > Port > COM#.The device is operated using three buttons:
Active Development - Version 0.1
| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7, C9, C11, C12, C15, C16, C17, C20, C23 |
| 9 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R11, R12, R16, R17, R18, R19, R20, R25 |
| 7 | 10u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4, C5, C6, C8 |
| 5 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R8, R9, R10, R15 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad | H1, H2, H3, H4 |
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C10, C21, C22 |
| 3 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D3, D4 |
| 2 | 18p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13, C14 |
| 2 | 1M | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R23, R24 |
| 2 | 27R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 2 | 4k7 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13, R14 |
| 2 | 5k1 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5, R6 |
| 2 | TBD | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C18, C19 |
| 1 | 10m | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R21 |
| 1 | 1A | Fuse:Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 1 | 1k3 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | 1u5 | Project_Library:TDK_VLS3012_3.0x3.0mm | L1 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | 470k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R22 |
| 1 | BAT54C | Package_TO_SOT_SMD:SOT-23_Handsoldering | D6 |
| 1 | BQ27411DRZT-G1A | Package_SON:Texas_S-PDSO-N12 | U5 |
| 1 | BTN_1_BOOT | Button_Switch_THT:SW_PUSH_6mm | SW4 |
| 1 | BTN_2 | Button_Switch_THT:SW_PUSH_6mm | SW3 |
| 1 | BTN_3 | Button_Switch_THT:SW_PUSH_6mm | SW5 |
| 1 | CR2032 | Battery:BatteryHolder_Keystone_3002_1x2032 | BT1 |
| 1 | ESP32-C3-WROOM-02 | RF_Module:ESP32-C3-WROOM-02 | U3 |
| 1 | GPS_PWR | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D7 |
| 1 | LED_PWR | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D5 |
| 1 | LOGO | Project_Library:bradysTag_3.5mm | G*** |
| 1 | LOGO | Project_Library:Coat of Arms Logo | G*** |
| 1 | MCP73871 | Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm | U1 |
| 1 | Molex 104031-0811 | Connector_Card:microSD_HC_Molex_104031-0811 | J4 |
| 1 | NEO-M9N | RF_GPS:ublox_NEO | U4 |
| 1 | NetTie_2 | NetTie:NetTie-2_SMD_Pad0.5mm | NT1 |
| 1 | PMOS | Package_TO_SOT_SMD:SOT-23_Handsoldering | Q1 |
| 1 | PROG | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | PRTR5V0U2X | Package_TO_SOT_SMD:SOT-143 | D2 |
| 1 | RESET | Button_Switch_THT:SW_PUSH_6mm | SW2 |
| 1 | SCL | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | SDA | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | SGGP.25.4.A.02 | Project_Library:Antenna_Taoglas_SGGP.25.4.A.02_25x25mm | AE1 |
| 1 | SHT30-DIS | Sensor_Humidity:Sensirion_DFN-8-1EP_2.5x2.5mm_P0.5mm_EP1.1x1.7mm | U6 |
| 1 | SW_PWR | Button_Switch_THT:SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | SW1 |
| 1 | Screw_Terminal_01x03 | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-3_1x03_P2.54mm_Horizontal | J3 |
| 1 | TBD | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L2 |
| 1 | TPS63031DSKR | Package_SON:WSON-10-1EP_2.5x2.5mm_P0.5mm_EP1.2x2mm | U2 |
| 1 | Test_Points | Connector_PinSocket_2.54mm:PinSocket_2x04_P2.54mm_Vertical | J2 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | VBCKP_TP | TestPoint:TestPoint_Pad_D1.0mm | VBCKP |
| 1 | VUSB | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | ~ | Project_Library:OLED_128x64_0.96in | DS1 |

polesskiy-dev/iot-risk-logger-stm32l4
Open IoT risk data logger based on STM32L4 MCU

Stab-Rabbit-coding/Serenity-UAV
A functional, security conscious, Unmanned Aerial Vehicle based on the Firefly Class spacecraft Serenity from the 2002 show..


jayis1/hardware-design-lab
Full-cycle hardware device designs — each device in its own subfolder with architecture, schematics, PCB layout, and software stack


polesskiy-dev/iot-risk-data-logger-nfc-samd21-hardware
Hardware (schematics, PCB, BOM) for iot-risk-data-logger-nfc-samd21 project

westphae/kingfisher
Go flight data recorder for a turbonormalized Beech Bonanza V35B, running on a Raspberry Pi 5

It measures 68 × 100 mm and has 4 copper layers, 1.6 mm thick.
90 parts, built around the ESP32-C3-WROOM-02-H4, MCP73871EV, NEO-M9N-00B and SHT30-DIS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the bkuhn4/golf-gps repository on GitHub, at the commit this page was made from: the board is src/hw/board_files/pocket-caddy.kicad_pcb and its schematic src/hw/board_files/KuhnYork_rev_0_1/microcontroller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask bkuhn4 before reusing the design.