4 layers43 × 25.8 mm
DVI receiver
openconcepts-ar/accel2d
This project aims to provide a graphics server system based on hardware accelerated graphics, and a easy way to develop the graphics primitives.
59 parts1
4 layers52.1 × 40.7 mm
100% Digital Video Solution for Original Xbox!
- Size
- 52.1 × 40.7 mm
- Copper layers
- 4
- Thickness
- 1.58 mm
- Parts
- 61
- Nets
- 106
- Pads
- 389
- Tracks, vias
- 662, 122
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 15 Sep 2024
- Updated
- 15 Sep 2024
Overview
XDV is an open-source printed circuit board by TeamFoxbat, from the TeamFoxbat/XDV repository on GitHub, published under the CERN-OHL-P-2.0 licence. It is a 4-layer board of 52.1 × 40.7 mm with 61 parts on 106 nets, routed with 662 tracks and 122 vias.
It is built around the STM32F030C8T6, RCLAMP0524P and YC124-JR-0733RL, with the 10029449-111RLF, 150060BS75000 and 150060VS75000 among its other parts. Its parts include 20 capacitors, 19 resistors, 6 diodes, 4 connectors and 4 inductors. It belongs with the STM32 boards of this library.
Main components
9
STM32F030C8T6
LQFP-48(7x7)-40℃~+85℃ 12bit 2.4V~3.6V 32 Bit 39 48MHz 64KB 8KB ARM Cortex-M0 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)RCLAMP0524P
DFN2510-10-55℃~+125℃ 0.35pF、0.8pF 17V 4.5A 5V 6.8V 80nA ESD Four channels IEC 61000-4-2 Unidirectional DFN2510-10 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)
YC124-JR-0733RL
0402x433Ω 4 62.5mW 8 ±200ppm/℃ ±5% 0402x4 Resistor Networks, Arrays ROHSYAGEOResistor Networks & Arrays
10029449-111RLF
SMDSMD HDMI Connectors ROHSAmphenolHDMI Connectors
150060BS75000
0603-40℃~+85℃ 1.1mm x 0.8mm square LED 1000V 105mW 140° 145mcd 20mA 25nm 3.2V 465nm 470nm Blue Discrete Diode InGaN Water Clear 0603 LED Indication - Discrete ROHSWürth ElektronikLight Emitting Diodes (LED)150060VS75000
SMD,1.6x0.8mm-40℃~+85℃ 140° 2.4V 20mA 40mcd 570nm 572nm 72mW Discrete Diode Green SMD,1.6x0.8mm LED Indication - Discrete ROHSWürth ElektronikLight Emitting Diodes (LED)
B5819WS-TP
SOD-323-65℃~+125℃ 1 Independent 10A 1A 40V 40uA@40V 600mV@1A SOD-323 Schottky Diodes ROHSMicro Commercial ComponentsSchottky Diodes
MIC5357-SGYMME
MSOP-8-EP-40℃~+125℃@(Tj) 1.8V、3.3V 130mV@(500mA) 160uA 2 45dB@(20kHz)、70dB 5.5V 500mA、500mA 51uVrms Fixed Over Current Protection、Over Temperature Protection、Enable Positive MSOP-8-EP Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMicrochip TechnologyUncategorised
MLZ1608N100LT000
060310uH 300mA 600mΩ 60mA Consumer grade Multilayer inductor ±20% 0603 Inductors (SMD) ROHSTDKInductors (SMD)
README
README.mdXDV
100% digital-to-digital video encoder inspired by existing projects for the Original Xbox. Currently no firmware released but is compatible with existing digital video encoding solutions.
Installation Notes
The v1.0-1.4 Xbox boards have a big electrolytic cap next to the stock encoder that will interfere with installation. Recommendation is to replace with a S1206 10uF ceramic.
The ferite bead on the bottom right of the stock encoder must be removed.
Notes for installing the power and SMBus harnesses to come soon.
Status Update
The Rev B board (not available here) does successfully take MakeMHz XboxHD+ firmware but has some visual glitches likely due to the flex PCB (not publicly available yet). Further work needs to be done to determine the cause but it's likely the flex.
The Rev C offers some minor improvements to reduce impedence mismatch on the TMDS traces but has not been ordered, a minor improvement to get closer to the spec.
Parts
61| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C4, C5, C6, C7, C8, C9, C10, C11, C12, C13, C20 |
| 5 | 10u | Capacitor_SMD:C_0603_1608Metric | C14, C15, C16, C17, C19 |
| 5 | 2k | Resistor_SMD:R_0402_1005Metric | R18, R19, R20, R21, R22 |
| 5 | 887R 1% | Resistor_SMD:R_0402_1005Metric | R4, R5, R7, R8, R16 |
| 3 | 220R@100MHz | Inductor_SMD:L_0603_1608Metric | L2, L3, L4 |
| 3 | 4k7 | Resistor_SMD:R_0402_1005Metric | R13, R15, R17 |
| 3 | RCLAMP0524P | footprints:DIO_RCLAMP0524PATCT | D1, D2, D3 |
| 3 | YC124-JR-0733RL | xboxhdmi:R_Array_Convex_4x0402 | R9, R10, R11 |
| 2 | MountingHole_Pad | MountingHole:MountingHole_4.3mm_M4_DIN965_Pad_TopBottom | H1, H2 |
| 1 | 0530470810 | footprints:MOLEX_0530470810 | J3 |
| 1 | 10029449-111RLF | footprints:HDMI_10029449 | J2 |
| 1 | 100R | Resistor_SMD:R_0402_1005Metric | R14 |
| 1 | 150060BS75000 | LED_SMD:LED_0603_1608Metric | LED2 |
| 1 | 150060VS75000 | LED_SMD:LED_0603_1608Metric | LED1 |
| 1 | 27k | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 47u | Capacitor_SMD:C_1206_3216Metric | C18 |
| 1 | 5034802400 | footprints:MOLEX_5034802400 | J1 |
| 1 | 53047-0210 | footprints:MOLEX_53047-0210 | J4 |
| 1 | ADV7511 | Package_QFP:LQFP-100_14x14mm_P0.5mm | U2 |
| 1 | B5819WS-TP | Diode_SMD:D_SOD-323 | D4 |
| 1 | Jumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | REC1 |
| 1 | MIC2091 | Package_TO_SOT_SMD:SOT-23-5 | VREG2 |
| 1 | MIC5357-SGYMME | Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP2.5x3mm_Mask1.73x2.36mm_ThermalVias | VREG1 |
| 1 | MLZ1608N100LT000 | Inductor_SMD:L_0603_1608Metric | L1 |
| 1 | PINHD-1X5 | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | JP1 |
| 1 | STM32F030C8T6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | YC124-JR-0733RL | Resistor_SMD:R_Array_Convex_4x0402 | R12 |
Questions
How big is the XDV PCB?
It measures 52.1 × 40.7 mm and has 4 copper layers, 1.58 mm thick.
What parts does the XDV use?
61 parts, built around the STM32F030C8T6, RCLAMP0524P, YC124-JR-0733RL and 10029449-111RLF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the XDV KiCad files?
From the TeamFoxbat/XDV repository on GitHub, at the commit this page was made from: the board is XDV-hardware/XDV.kicad_pcb and its schematic XDV-hardware/XDV.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the XDV design in my own project?
Its repository publishes it under the CERN-OHL-P-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 4 layers88.1 × 34.5 mm
Servid rp2040-hdmi proto rev1
baldengineer/Mega-IIe
Using the Mega II from a IIgs to make a Apple IIe compatible computer: The Mega IIe!
105 parts33MIT - 2 layers240 × 110 mm
- 8 layers245 × 129 mm
- 4 layers72.8 × 75 mm
Rover circuit
Project-Emerge/rover-circuit
The Rover Circuit is a comprehensive controller board designed for robotics applications, specifically targeted at robot rovers.
108 partsMIT - 4 layers76.9 × 67.3 mm
- 2 layers80 × 100 mm
- 4 layers90 × 40 mm
Linear act controller
Talw3g/linear_act_controller
Controller for 24V linear actuator with potentiometer position control and feedback.
80 parts