
Ogham merged v1.0
keeos-io/ogham
Ogham — a dual-voice bytebeat synthesizer for Eurorack. Firmware (MIT) and hardware (CC BY-SA 4.0).

A custom configurable gauge for K-line OBD interfaces
OBDGauge is an open-source printed circuit board by tealvince, from the tealvince/OBDGauge repository on GitHub, published under the GPL-2.0 licence. It is a 2-layer board with 25 parts on 37 nets, routed with 167 tracks and 0 vias.
It is built around the TM1637 and LM2903. Its parts include 8 resistors, 4 connectors, 2 diodes, 2 switches and 1 capacitor. It belongs with the interfaces and adapters boards of this library.
By Vince Lee (c)2024-2026
This project is a custom OBD cluster gauge and experimentation platform for ECUs with a k-line interface, driven by an Arduino nano and intended to be installed in a 2" diameter circular pod.



To read to and write from the K-Line, a dual comparator chip does the work of converting between 5V and 12V logic levels, using voltage dividers to yield 6V and 2.5V reference voltages. The output of the "write" comparator goes to a PNP transistor to pull the k-line low when sending data back to the PCM, safely sinking more current than the comparator can on its own.
To power the arduino, an ignition-switched 12V output is fed to the built-in regulator on the Arduino Nano Every (previous iterations used an external voltage regulator with a plain Arduino Nano, whole upper voltage limit was only 12V). A large capacitor briefly keeps the unit running long enough to save state to persistent memory after the ignition is turned off.
The gauge software is written in C++ with minimal libraries to drive the LED displays. Serial communication is done with raw bit banging, implementing serial port communication purely in software timed off the Arduino microsecond timer.
Try out the software or experiment with code changes in a simulated environment using the following WOKWI project. Recommend enabling Demo Mode from the settings menu since the ECU itself is not simulated:
https://wokwi.com/projects/430523461712229377
The case and internal spacers and supports are 3D printed. Stl files are included, as well as an svg for the front glass with laser cut holes for the buttons.
Case parts include:
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 15K | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R2, R3, R4, R6 |
| 2 | GND | TEST2, TEST3 LOG | |
| 2 | MountingHole_2.1mm | MountingHole:MountingHole_2.1mm | HOLE1, HOLE2 |
| 1 | +12 | TestPoint:TestPoint_Loop_D3.50mm_Drill0.9mm_Beaded | TEST1 |
| 1 | 10000uF | Capacitor_THT:CP_Radial_D8.0mm_P5.00mm | C1 |
| 1 | 10K | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R8 |
| 1 | 1K | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R7 |
| 1 | 30K | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R5 |
| 1 | 3906 | Package_TO_SOT_THT:TO-92 | Q1 |
| 1 | 9V REG | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | Diode | Diode_THT:D_DO-35_SOD27_P12.70mm_Horizontal | D1 |
| 1 | LED | LED_THT:LED_D3.0mm | D2 |
| 1 | LM2903 | Package_DIP:DIP-8_W7.62mm_Socket_LongPads | U1 |
| 1 | NANO EVERY | Module:Arduino_Nano | A1 |
| 1 | Neopixel | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | OBD | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | SW1 | Button_Switch_THT:SW_PUSH_6mm_H8.5mm | SW1 |
| 1 | SW2 | Button_Switch_THT:SW_PUSH_6mm_H8.5mm | SW2 |
| 1 | TM1637 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |

keeos-io/ogham
Ogham — a dual-voice bytebeat synthesizer for Eurorack. Firmware (MIT) and hardware (CC BY-SA 4.0).

bitsandpixels-io/kids-control-panel
Spaceship-like control panel for kids, based on Arduino

fehlfarbe/ESP32-Alarm-clock
This is an ESP32 based alarm clock that plays mp3 files from SD, webstreams or even FM radio. You can configure multiple alarms and add new songs to your sd card with a simple webinterface.

galopago/panel-mount-7-segment-display
Open source 7 segment serially controlled led display that fits inside a generic 45x26mm panel mount plastic enclosure. Upgrade your function specific panel meter PCB with a new one controllable by your preferred MCU.

pmalessa/homegreen-Node
The system is based on an inexpensive node, which is able to control up to 3 pumps and can be powered by nearly any conventional powerbank.


25 parts, built around the TM1637 and LM2903. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the tealvince/OBDGauge repository on GitHub, at the commit this page was made from: the board is src/kicad/OBDGauge.kicad_pcb and its schematic src/kicad/OBDGauge.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).