Skip to the content
2 layers92.5 × 41.3 mmButton panel, the printed circuit board in 3D

ROS based UAV (Unmanned Autonomous Vehicle), Master's degree final project

Size
92.5 × 41.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
36
Nets
26
Pads
133
Tracks, vias
389, 9
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
4 Dec 2020
Updated
7 Nov 2021

Overview

Button panel is an open-source printed circuit board by Tai-Min, from the Tai-Min/Statek-UAV repository on GitHub, published under the MIT licence. It is a 2-layer board of 92.5 × 41.3 mm with 36 parts on 26 nets, routed with 389 tracks and 9 vias.

Its parts include 14 resistors, 9 switches, 7 diodes and 2 connectors. It belongs with the sensors and measurement and robots and motor control boards of this library.

README

README.md

Statek-UAV

ROS based UAV, Master's degree final project.

This repository consists of CAD files for the chassis, CAD files for electronic boards, catkin workspace for all ROS nodes created for the project and some additional scripts used during development.

The core part of this project is the real, 3D printed vehicle along with all the hardware attached to it (Jetson Nano B01 for main controller and STM32f103RBT6 for real time core).

The software part of this project can be split into real time (closed loop wheel control), short term navigation (movement between two GPS waypoints) and long term navigation (navigation through series of GPS waypoints). During the project's development, my main focus was on short term navigation, which is also the biggest and most complicated part of the project. Short term navigation stack consists of static local map generator, dynamic local map generator (human leg detector mostly based on U-Net fully convolutional neural network), Voronoi graph generator, A* path planner and non linear model predictive controller for navigation.

For more info see this arcitle.

Just to warn you: If you want to use this project somehow, use it as reference only. It is NOT meant to be assembled as it contains some design flaws both in hardware and software that I don't intent to fix in this iteration of the project as code in this repository will stay in unchanged since the moment I handed over my thesis. Most of the files in the "instructions" folder consists of the steps I've did to setup my hardware and Ipopt solver. Those might not work for you/could be dangerous (I might've abused sudo a bit) so use them at your own risk. The code quality depends on the time I had untill the deadline to hand over my thesis. In my opinion it should be fine for the most part, well documented and easy to follow but judge for yourself.

Disclaimer: I've tried to credit all authors of 3D files used in the project. All of the models had permissive license allowing me to use them. If you see your work here without being credited or you just don't want to have your files used here - open an issue on this project and I'll fix any problems.

The files in this folder have the following structure:

  • CAD
    • detailed - Inventor files for the 3D printing and assembling.
    • low_poly - Inventor files for simple low poly model for Gazebo and Rviz.
  • catkin_ws/src
    • statek - Metapackage for the project
    • statek_calibrate - Calibration algorithms for cameras, GPS Kalman filter, IMU, Motor's PI controller autotuning.
    • statek_config - Config files for the robot, including transformations, urdf and parameters for ROS nodes.
    • statek_hw - code to launch hardware based nodes (lidar, rosserial, cameras etc.) along with source code for real time controller.
    • statek_map - Mapping algorithms (dynamic local mapper, voronoi generator and GPS to hyperplane casting).
    • statek_ml - Leg detector based mostly on U-net fully convolutional neural network
    • statek_nav - Navigation algorithms (NMPC and GPS waypoint follower script).
    • statek_plan - A* path planner for short term navigation.
    • statek_playground - Simple launch nodes to play with the hardware.
    • statek_rviz - Rviz visualization files.
    • statek_sim - Gazebo simulation files.
    • statek_srv - Server files to communicate with web application (really rough draft).
    • statek_teleop - Teleoperation nodes for Dualshock 4 gamepad.
  • electronics
    • AM4096_encoder - KiCad's files for AM4096 encoder board.
    • Nucleo_screw_shield - KiCad's files for screw shield that fits morpho connector.
    • button_panel - Unused in the project.
    • connections - Electrical connections of the project.
  • instructions - Rough draft of what I did to setup the robot.
  • media - Contains camera's calibration chessboard.
  • thesis_scripts - Some files used to add more value to the project.

alt text

Parts

36
QtyValueFootprintReferences
14RResistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolderR1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11, R12, R13, R14
1AUTO CTRLButton_Switch_THT:SW_PUSH_6mmSW4
1AUTO CTRLLED_THT:LED_D5.0mm_ClearD2
1Conn_01x09Connector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_VerticalJ2
1Conn_01x10Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_VerticalJ1
1FC RECButton_Switch_THT:SW_PUSH_6mmSW5
1PWRLED_THT:LED_D5.0mm_ClearD4
1PWRButton_Switch_THT:SW_PUSH_6mmSW1
1RSTButton_Switch_THT:SW_PUSH_6mmSW2
1USR0LED_THT:LED_D5.0mm_ClearD3
1USR0Button_Switch_THT:SW_PUSH_6mmSW3
1USR1Button_Switch_THT:SW_PUSH_6mmSW6
1USR1LED_THT:LED_D5.0mm_ClearD7
1USR2LED_THT:LED_D5.0mm_ClearD6
1USR2Button_Switch_THT:SW_PUSH_6mmSW7
1USR3Button_Switch_THT:SW_PUSH_6mmSW8
1USR3LED_THT:LED_D5.0mm_ClearD5
1USR4Button_Switch_THT:SW_PUSH_6mmSW9
1USR4LED_THT:LED_D5.0mm_ClearD1

The 32 most common of 36 parts.

More from Tai-Min/Statek-UAV

2
  • 2 layers91 × 95.3 mmScrew connector, the printed circuit board in 3D

    Screw connector

    Tai-Min/Statek-UAV

    ROS based UAV (Unmanned Autonomous Vehicle), Master's degree final project

    642 parts6MIT
  • 2 layers39.9 × 40 mmEnkoder, the printed circuit board in 3D

    Enkoder

    Tai-Min/Statek-UAV

    ROS based UAV (Unmanned Autonomous Vehicle), Master's degree final project

    21 parts6MIT

Similar boards

  • 2 layers65 × 30 mmRgb to hdmi, the printed circuit board in 3D

    Rgb to hdmi

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    36 parts1kGPL-3.0
  • 2 layers55 × 70 mmArduino v1, the printed circuit board in 3D

    Arduino v1

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    36 parts915
  • 2 layers50.4 × 24.8 mmLEDboardRev3, the printed circuit board in 3D

    LEDboardRev3

    Architeuthis-Flux/Jumperless

    A jumperless breadboard

    36 parts914
  • 2 layers45.7 × 31.8 mmLEDx16 board, the printed circuit board in 3D

    LEDx16 board

    tardate/LittleArduinoProjects

    a collection of "Little Electronic & Arduino Projects", most involving electronics or an Arduino in one way or another!

    36 parts803MIT
  • 2 layers32 × 24 mmEsp onelayer3, the printed circuit board in 3D

    Esp onelayer3

    cnlohr/colorchord

    Chromatic Sound to Light Conversion System

    36 parts712
  • 2 layers69 × 53.8 mmTUSS4470 shield, the printed circuit board in 3D

    TUSS4470 shield

    Neumi/open_echo

    Open Source echo sounder / depth sounder / SONAR for bathymetry and research. Arduino based and compatible.

    36 parts530
  • 2 layers99.1 × 53.3 mmABSIS Mega, the printed circuit board in 3D

    ABSIS Mega

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    36 parts431
  • 2 layers16.1 × 119 mmConnectorL, the printed circuit board in 3D

    ConnectorL

    thpoll83/PolyKybd

    PolyKybd

    36 parts411CERN-OHL-W-2.0

Questions

How big is the Button panel PCB?

It measures 92.5 × 41.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Button panel use?

36 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Button panel KiCad files?

From the Tai-Min/Statek-UAV repository on GitHub, at the commit this page was made from: the board is electronics/button_panel/button_panel.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Button panel design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).