Skip to the content
2 layers100 × 50 mmFlyback, the printed circuit board in 3D

Design reports and schematics on flyback converter

Size
100 × 50 mm
Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
19
Pads
38
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 10.0 (file 20260206)
Created
2 Sep 2026
Updated
22 Oct 2026

Overview

Flyback is an open-source printed circuit board by surycgnuhc, from the surycgnuhc/flyback_converter repository on GitHub. It is a 2-layer board of 100 × 50 mm with 11 parts on 19 nets.

It is built around the MCQ15N10YA-TP and UF4007. Its parts include 3 capacitors, 3 resistors, 2 diodes, 1 transistor and 1 connector.

Main components

2

README

kicad/flyback_kicad/README.md

Flyback KiCad project: 24V in, 12V/2A out, 100kHz

Power stage only, ported from the validated LTspice circuit. Made in KiCad 7 format. KiCad 8 and 9 open it and offer to upgrade the files: click Yes.

Open it

  1. Unzip the folder and keep every file together.
  2. KiCad > File > Open Project > flyback.kicad_pro.
  3. Double-click flyback.kicad_sch (schematic) or flyback.kicad_pcb (board).

Get to a printable PCB

  1. Schematic: double-click T1, set the Footprint field (see gaps below).
  2. References (R1, C1 ...) are already set, no annotation needed.
  3. PCB Editor: Tools > Update PCB from Schematic (F8) > Update PCB. All footprints and nets load; click to drop them on the board.
  4. Place parts, then route with X. Keep GND_PRI and GND_SEC separate.
  5. Draw the board outline on layer Edge.Cuts (Place > Line, then close the shape).
  6. File > Print, or File > Plot for Gerbers.

Nets (matches LTspice)

NetPins
VINJ1.1, T1.1 (dot), C3.1, R1.1
GND_PRIJ1.2, J3.2, Q1.S (1-3), R3.2
DRAINT1.2, Q1.D (5-8), D2 anode
SNUBD2 cathode, C3.2, R1.2
SEC_ACT1.4, D1 anode
VOUTD1 cathode, C1+, C2+, J2.1
GND_SECT1.3 (dot), C1-, C2-, J2.2
GATE_DRVJ3.1, R2.1
GATER2.2, Q1.G (4), R3.1

Parts

RefPartFootprint
Q1MCQ15N10YA-TPSOIC-8 (S=1-3, G=4, D=5-8, from MCC datasheet)
D11N5822 SchottkyDO-201AD
D2UF4007DO-41
C1, C247uF/25V electrolyticRadial D6.3mm, pin 1 = +
C3560nF/100V filmRect 7.2 x 5.5mm, 5mm pitch
R1390 ohm, 5WAxial power 22.4mm
R2, R310 ohm, 10kAxial DIN0207
J1, J22-pin terminal block5.08mm
J32-pin header (gate drive in)2.54mm
T1Lp 20.7uH, Np:Ns = 1:1.57none yet

Known gaps

  • T1 has no footprint. Pick one once the core and bobbin are chosen (or a placeholder header for bench wiring).
  • No PWM controller, current sense resistor or feedback loop. Gate is driven externally through J3.
  • R2 (10 ohm) and R3 (10k) are not in the LTspice simulation yet.
  • Q1 is the only SMD part (SOIC-8); everything else is through-hole.
  • R1 dissipates about 2.3W at the 30V clamp (30V^2 / 390 ohm), so the 5W part has 2x margin.
  • 24V prototype spacing only. The 90-264VAC version needs new creepage and clearance.

Parts

11
QtyValueFootprintReferences
247u/25VCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC1, C2
110Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2
110kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3
11N5822Diode_THT:D_DO-201AD_P15.24mm_HorizontalD1
1390 5WResistor_THT:R_Axial_Power_L20.0mm_W6.4mm_P22.40mmR1
1560n/100V filmCapacitor_THT:C_Rect_L7.2mm_W5.5mm_P5.00mm_FKS2_FKP2_MKS2_MKP2C3
1GATE_DRIVEConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ3
1Lp=20.7uH Np:Ns=1:1.57750311797:WE-FB_EFD20T1
1MCQ15N10YA-TPPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmQ1
1UF4007Diode_THT:D_DO-41_SOD81_P10.16mm_HorizontalD2

Similar boards

  • 2 layers68 × 89 mmParanoiaBox, the printed circuit board in 3D

    ParanoiaBox

    profdc9/ParanoiaBox

    A standalone elliptic curve/AES file encryption and decryption device

    60 parts17
  • 2 layers96.3 × 98 mmAquarium, the printed circuit board in 3D

    Aquarium

    baranovskiykonstantin/aquarium

    Control the lighting and the heating of the aquarium.

    73 parts11
  • 2 layers100 × 70 mmMotorDriver, the printed circuit board in 3D

    MotorDriver

    JeyRunner/actonator

    3D printable robot actuator with belt-driven gearbox and custom FOC driver board.

    177 parts10MIT
  • 2 layers156.5 × 67.5 mmNixieScanDisplay, the printed circuit board in 3D

    NixieScanDisplay

    profdc9/NixieClock

    A Nixie clock that uses IN-14 tubes and very generic components that can be easily sourced.

    106 parts10
  • 4 layers147.8 × 77 mm2xBLDCPicoV3, the printed circuit board in 3D

    2xBLDCPicoV3

    AmericanRework/Pico-2x-BLDC

    One RP2040 Pico drives two brushless motors! SimpleFOC + Halls + 2304 drivers + TO-220 mosfets or IGBTs. Plugs directly into 450x automower motors.

    135 parts7
  • 2 layers373 × 132.3 mmSolarinverter, the printed circuit board in 3D

    Solarinverter

    cpipero/solarinverter

    Kicad Project to build a programmable Solar Inverter

    370 parts5CC0-1.0
  • 2 layers329.9 × 146.6 mmBabyHuey, the printed circuit board in 3D

    BabyHuey

    tristancollins/HiFi-BabyHuey

    An "Engineer's" Baby Huey EL34 PCB

    201 parts5
  • 2 layers30 × 100 mmMoskill, the printed circuit board in 3D

    Moskill

    telagod/moskill

    MosKill - Smart Mosquito Swatter with BLE, Kill Counting & Statistics | ESP32-C3 + KiCad PCB + UniApp

    95 parts2

Questions

How big is the Flyback PCB?

It measures 100 × 50 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Flyback use?

11 parts, built around the MCQ15N10YA-TP and UF4007. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Flyback KiCad files?

From the surycgnuhc/flyback_converter repository on GitHub, at the commit this page was made from: the board is kicad/flyback_kicad/flyback.kicad_pcb and its schematic kicad/flyback_kicad/flyback.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Flyback design in my own project?

Its repository states no licence, so its author keeps all rights: ask surycgnuhc before reusing the design.