

Telemetry emulator pcb
- Size
- 100 × 50 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 56
- Nets
- 70
- Pads
- 225
- Tracks, vias
- 463, 65
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 2 Aug 2022
- Updated
- 3 Dec 2022
Overview
Telemetry emulator pcb is an open-source printed circuit board by supermileage, from the supermileage/telemetry-emulator-pcb repository on GitHub, published under the MIT licence. It is a 2-layer board of 100 × 50 mm with 56 parts on 70 nets, routed with 463 tracks and 65 vias.
It is built around the ATMEGA328-PU, CH340C and MCP2551-I/P, with the MCP2515-I and BSS138 among its other parts. Its parts include 14 resistors, 13 capacitors, 8 connectors, 5 diodes and 4 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
5ATMEGA328-PU
PDIP-28-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH PDIP-28 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)CH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersMCP2551-I/P
PDIP-8-40℃~+85℃ 1Mbps 365uA 4.5V~5.5V 75mA CAN Transceiver PDIP-8 CAN Transceivers ROHSMicrochip TechnologyCAN TransceiversMCP2515-I
TSSOP-20-40℃~+85℃ 1Mbps 1uA 2.7V~5.5V 5mA CAN Controller SPI TSSOP-20 CAN Controllers ROHSTokmasCAN ControllersBSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETs
README
README.mdtelemetry-emulator-pcb
Parts
56| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C1, C2, C4, C7, C8, C11, C13 |
| 7 | 10K | Resistor_SMD:R_0805_2012Metric | R1, R8, R9, R10, R11, R12, R13 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H2, H3, H4, H5 |
| 2 | 1.2K | Resistor_SMD:R_0805_2012Metric | R5, R6 |
| 2 | 1.5K | Resistor_SMD:R_0805_2012Metric | R4, R7 |
| 2 | 10uF | Capacitor_SMD:C_1206_3216Metric | C3, C12 |
| 2 | 16pF | Capacitor_SMD:C_0805_2012Metric | C9, C10 |
| 2 | 18pF | Capacitor_SMD:C_0805_2012Metric | C5, C6 |
| 2 | 1K | Resistor_SMD:R_0805_2012Metric | R2, R3 |
| 2 | BSS138 | digikey-footprints:SOT-23-3 | Q1, Q2 |
| 2 | CAN | Connector_Molex:molex-sl-1x03-horizontal | J7, J8 |
| 1 | 120 | Resistor_SMD:R_0805_2012Metric | R14 |
| 1 | 16MHz | Crystal:Crystal_SMD_HC49-SD | Y1 |
| 1 | 500mA | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | 8MHz | Crystal:Crystal_SMD_HC49-SD | Y2 |
| 1 | ATmega328P | Package_QFP:TQFP-32_7x7mm_P0.8mm | IC1 |
| 1 | CAN_TERM | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | CH340C | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U1 |
| 1 | GPIO | Connector_PinHeader_2.54mm:PinHeader_2x13_P2.54mm_Vertical | J3 |
| 1 | ICSP | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | H1 |
| 1 | LOGO | LOGO | G*** |
| 1 | MCP2515 | Package_SO:SOIC-18W_7.5x11.6mm_P1.27mm | IC2 |
| 1 | MCP2551 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | IC3 |
| 1 | RESET | Button_Switch_THT:SW_PUSH_6mm | S1 |
| 1 | RX_TX | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J2 |
| 1 | Schottky | Diode_SMD:D_SOD-323 | D5 |
| 1 | UART | Molex_SL:molex_sl_1x04_horizontal | J6 |
| 1 | USB | Connector_USB:USB_Micro-B_Molex_47346-0001 | J1 |
| 1 | V_INT | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | blue | LED_SMD:LED_0805_2012Metric | D3 |
| 1 | green | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | orange | LED_SMD:LED_0805_2012Metric | D4 |
| 1 | red | LED_SMD:LED_0805_2012Metric | D1 |
Similar boards
- 2 layers105.4 × 67.6 mm

- 2 layers140 × 90 mm

Metaldetector
sharst/metaldetector-shield
Hardware and Software for a custom build metaldetector + pressure sensing shield
149 parts4LGPL-3.0 - 2 layers68.7 × 53.5 mm

Sensor interface 1.1.0
WATonomous/interfacing-mono
repo for all firmware, ROS nodes, messages, and schematics to live
61 parts1 - 2 layers97 × 58 mm

- 2 layers100 × 51 mm

- 2 layers70 × 55 mm

- 2 layers31.8 × 54.6 mm

- 2 layers

ControlBoard
knoerk/MicroGasExchange
Software, Circuits and PCB for microcontroller based gas exchange system
106 partsGPL-3.0
Questions
How big is the Telemetry emulator pcb PCB?
It measures 100 × 50 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Telemetry emulator pcb use?
56 parts, built around the ATMEGA328-PU, CH340C, MCP2551-I/P and MCP2515-I. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Telemetry emulator pcb KiCad files?
From the supermileage/telemetry-emulator-pcb repository on GitHub, at the commit this page was made from: the board is telemetry-emulator-pcb.kicad_pcb and its schematic telemetry-emulator-pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Telemetry emulator pcb design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).