4 layers75 × 55 mm
HIDMorph
cedarhacks/HIDMorph
Hardware/Firmware of HIDMorph, a lua configurable HID translation/generation device
50 parts4
4 layers76.7 × 45.3 mm
ReMapper
sulicat/hardware- Size
- 76.7 × 45.3 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 46
- Nets
- 91
- Pads
- 255
- Tracks, vias
- 447, 97
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 29 Mar 2025
- Updated
- 8 Nov 2025
Overview
ReMapper is an open-source printed circuit board by sulicat, from the sulicat/hardware repository on GitHub. It is a 4-layer board of 76.7 × 45.3 mm with 46 parts on 91 nets, routed with 447 tracks and 97 vias.
It is built around the RP2040, ESP32-S3-WROOM-1-N8R8 and W25Q128JVEIQ, with the SPX1117M3-L-3-3/TR and SKRPABE010 among its other parts. Its parts include 14 capacitors, 9 diodes, 7 resistors, 5 ICs and 3 switches. It belongs with the ESP32 and RP2040 boards of this library.
Main components
5
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
ESP32-S3-WROOM-1-N8R8
SMD,25.5x18mm-104.5dBm -40℃~+65℃ 2.4GHz 20.5dBm 330mA 3V~3.6V 97mA Bluetooth5.0 ESP32-S3R8 On-board PCB Antenna UART、SPI、I2C、GPIO、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi Modules
W25Q128JVEIQ
WSON-8-EP(6x8)-40℃~+85℃ 100,000 cycles 10uA 128Mbit 133MHz 2.7V~3.6V 20 Years Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection、Power lock protection SPI WSON-8-EP(6x8) NOR FLASH ROHSWinbondNAND FLASH
SPX1117M3-L-3-3/TR
SOT-223-3-40℃~+125℃ 0.003%Vout 1 1.3V@(800mA) 10mA 20V 3.3V 70dB@(120Hz) 800mA Fixed Over Current Protection、Over Temperature Protection Positive SOT-223-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMaxLinearVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
SKRPABE010
SMD-4P,4.2x3.2mm-30℃~+85℃ 1.6N 100,000 cycles 16V 2.5mm 3.2mm 4.2mm 50mA J-Lead Oval button SPST-NO Surface Mount,Vertical SMD-4P,4.2x3.2mm Tactile Switches ROHSALPSALPINETactile Switches
Parts
46| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 500 | Resistor_SMD:R_0603_1608Metric | R5, R6, R7, R8 |
| 4 | ESD | Diode_SMD:D_SOD-523 | D2, D3, D4, D5 |
| 3 | 2.2uf | Capacitor_SMD:C_0603_1608Metric | C4, C9, C13 |
| 3 | 47uF | Capacitor_SMD:C_0603_1608Metric | C8, C14, C16 |
| 3 | SKRPABE010 | footprints:push_button_SKRPABE010 | S1, S2, S3 |
| 2 | 0.1uf | Capacitor_SMD:C_0603_1608Metric | C2, C15 |
| 2 | 100nf | Capacitor_SMD:C_0603_1608Metric | C5, C10 |
| 2 | 15 pF | Capacitor_SMD:C_0603_1608Metric | C11, C12 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | LED RP5 | LED_SMD:LED_0603_1608Metric | LED3, LED4 |
| 2 | W25Q128JVE | Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm | U3, U5 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 12MHZ | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y2 |
| 1 | 1uf | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | 22uf | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | D_Schottky | Diode_SMD:D_SOD-123 | D1 |
| 1 | ESP32-S3-WROOM-1-N8R8 | RF_Module:ESP32-S3-WROOM-1 | U1 |
| 1 | ESP_UART0 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | ESP_UART0 |
| 1 | LED 33V | LED_SMD:LED_0603_1608Metric | LED1 |
| 1 | LED USB VIN | LED_SMD:LED_0603_1608Metric | LED2 |
| 1 | QSPI_Debug | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | ESP_QSPI1 |
| 1 | RP2040 | footprints:rp2040 | U2 |
| 1 | SPX1117M3-L-3-3/TR | Package_TO_SOT_SMD:SOT-223 | U6 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | RP_SWD1 |
| 1 | USB_IN | footprints:USBA_Female | J2 |
| 1 | USB_IN_Debug | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | USB_IN1 |
| 1 | USB_OUT | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J5 |
| 1 | VIN_Schottky | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1 |
Questions
How big is the ReMapper PCB?
It measures 76.7 × 45.3 mm and has 4 copper layers, 1.6 mm thick.
What parts does the ReMapper use?
46 parts, built around the RP2040, ESP32-S3-WROOM-1-N8R8, W25Q128JVEIQ and SPX1117M3-L-3-3/TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ReMapper KiCad files?
From the sulicat/hardware repository on GitHub, at the commit this page was made from: the board is ReMapper/electrical/ReMapper/ReMapper.kicad_pcb and its schematic ReMapper/W25Q128JV_breakout/W25Q128JV_breakout/W25Q128JV_breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ReMapper design in my own project?
Its repository states no licence, so its author keeps all rights: ask sulicat before reusing the design.
Similar boards
- 2 layers20 × 20 mm
B SPX1117-3V3-BRK R1.0
Boardoza/Boardoza_SPX1117-3V3_LDO_Regulator_Breakout_Board
Boardoza SPX1117-3V3 Breakout Board provides a stable and low-noise 3.3V regulated power supply with up to 800mA output current.
11 partsCC-BY-SA-4.0 - 2 layers43 × 43 mm
- 2 layers133.1 × 77.2 mm
- 2 layers55 × 55 mm
- 4 layers50.8 × 25.4 mm
- 4 layers17.8 × 41.9 mm
- 2 layers323.9 × 115.5 mm
