
Alpakka
stormbots/MarketingBot
See the attached Wiki for documentation about the general system functionality

See the attached Wiki for documentation about the general system functionality
Control Board is an open-source printed circuit board by stormbots, from the stormbots/MarketingBot repository on GitHub. It is a 2-layer board of 120.7 × 77.5 mm with 57 parts on 77 nets, routed with 300 tracks and 29 vias.
It is built around the SN74LVC245APW, ULN2003 and BSS138. Its parts include 17 resistors, 6 diodes, 2 ICs, 1 transistor and 1 connector.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 22 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | 12V_INPUT1, MC1A1, MC1B1, MC1C1, MC2A1, MC2B1, MC2C1, MC3, MC4, MC5, MC6, MC7, MC8, PCM1, PCM2, PCM3 +6 |
| 9 | 10kOhms | Resistor_SMD:R_0805_2012Metric | R9, R10, R11, R12, R13, R14, R15, R16, R17 |
| 8 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R2, R3, R4, R5, R6, R7, R8 |
| 4 | Conn_01x04_Pin | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | D36V6F3, I2C1, QUAD1, QUAD2 |
| 2 | 3220-10-0100-00 | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical | QUAD1_CTRE1, QUAD2_CTRE1 |
| 2 | SolderJumper_3_Open | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabels | JP4, JP5 |
| 2 | SolderJumper_3_Open | Jumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabels | JP2, JP3 |
| 1 | Adafruit_Feather_M0_RFM9x_LoRa_Radio | Module:Adafruit_Feather_M0_RFM | A1 |
| 1 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | Conn_01x02_Pin | TerminalBlock_MetzConnect:TerminalBlock_MetzConnect_Type086_RT03402HBLC_1x02_P3.81mm_Horizontal | J1 |
| 1 | D | Diode_SMD:D_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | D | Diode_SMD:D_1206_3216Metric | D1 |
| 1 | SN74LVC245APW | Package_DIP:DIP-20_W7.62mm_LongPads | U1 |
| 1 | SolderJumper_2_Bridged | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP1 |
| 1 | ULN2003 | Package_DIP:DIP-16_W7.62mm_LongPads | U2 |

stormbots/MarketingBot
See the attached Wiki for documentation about the general system functionality

stormbots/MarketingBot
See the attached Wiki for documentation about the general system functionality


Anderman/Renovent
Display is een liteon De 8 segementen worden in volgorde aan gestuurd met een freq van 500uS Welke segmenten verlicht worden gaat met digit 1 - 4


TheYoctoJester/dutler
A bench butler for your Device Under Test: turns a Raspberry Pi Pico into a USB-serial console bridge with power-relay and MOSFET strap/reset control for embedded-Linux bring-up and hardware-in-the-loop.


MicroCoreLabs/Projects
Ted Fried's MicroCore Labs Projects - FPGA CPU cores and emulators for the 8088, 8086, 8051, 6502, 68000, Z80, Risc-V, and also Typewriter and EPROM Emulator projects.

fliperama86/neopico-hd
Digital video and audio capture with HDMI output for Neo Geo MVS arcade hardware using Raspberry Pi Pico 2

lmcapacho/ESP32_LogicAnalyzer
Low-cost logic analyzer using ESP32 for fast digital signal debugging
It measures 120.7 × 77.5 mm and has 2 copper layers, 1.6 mm thick.
57 parts, built around the SN74LVC245APW, ULN2003 and BSS138. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the stormbots/MarketingBot repository on GitHub, at the commit this page was made from: the board is ControlBoard/Control Board.kicad_pcb and its schematic Control Box Interface Board/board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask stormbots before reusing the design.