
A1200KB DB37
steveed/a1200kb-external-case
Some ideas for using an external Amiga keyboard with an A1200 in a desktop or tower case.

Some ideas for using an external Amiga keyboard with an A1200 in a desktop or tower case.
A1200KB Encoder is an open-source printed circuit board by steveed, from the steveed/a1200kb-external-case repository on GitHub. It is a 2-layer board of 75.1 × 29.6 mm with 18 parts on 49 nets, routed with 759 tracks and 61 vias.
It is built around the ATMEGA4809-AF, CC0603KRX7R9BB104 and PESD5V0S1BA,115-MS, with the CL21A106KAYNNNE and DIN-504 among its other parts. Its parts include 5 resistors, 4 capacitors, 4 connectors, 2 diodes and 1 IC. It belongs with the keyboards and input boards and the AVR (ATmega, ATtiny) boards of this library.
Run an A1200KBv2 mechanical keyboard in its own external case, connected by cable to an A1200 motherboard in a case with no built-in keyboard, such as the Checkmate 1500 Plus.
Normally an external case means a PS/2 or USB keyboard and an adapter. This project keeps the real A1200 keyboard instead.

Setting one up, or stuck? The setup guide shows each way of connecting, what (if anything) has to change on the A1200, the cable wiring, and a troubleshooting table.
The A1200 keyboard has no controller of its own. It is a bare switch matrix scanned by the keyboard controller on the motherboard, so every one of the 31 lines on the keyboard ribbon (FFC) has to reach the motherboard. DB25 has too few pins, so this uses DB37:
A1200 motherboard ── FFC ── [adapter] ══ DB37 cable ══ [adapter] ── FFC ── A1200KBv2 keyboard
LED header ──────────── J2 J2 ──────────────── keyboard LED headerBoth ends use the same adapter board. See adapter/Readme.md for the pinout, build options and parts.
On A1200 boards with the CN17 "KB TEST" header, the keyboard controller's serial lines are available directly:
A1200KBv2 ── [encoder] ══ DIN 5 cable ══ [din5 board] ── A1200 CN17din5/ gives the A1200 a standard 5-pin DIN keyboard socket. An A2000/A3000 keyboard (or an A4000 one through a PS/2-to-AT adapter) plugs straight in. No firmware.encoder/ turns the A1200KBv2 into a standard Amiga keyboard with that same DIN 5, so it also works on an A2000/A3000. It has the same outline as the DB37 adapter, so either fits the case. The activity LEDs don't come across; the power LED does.adapter/ — KiCad 10 project for the FFC ⇄ DB37 adapter board, with Gerbers in adapter/fab/encoder/ — KiCad 10 project for the A1200KBv2 to Amiga keyboard (DIN 5) encoder, with Gerbers in encoder/fab/din5/ — KiCad 10 project for the A1200 standard keyboard socket (CN17 to DIN 5), with Gerbers in din5/fab/lib/A1200KB.pretty — footprints shared by those boards (DIN 5)case/ — OpenSCAD model of the keyboard case (see case/Readme.md)docs/ — setup guide, wiring diagrams and renders (docs/render.sh regenerates the images)Rev 1 of the adapter is designed but not built or tested. The encoder and din5 boards are designed and routed; the encoder has no firmware yet. Before ordering adapter boards:
CC-BY-NC-SA 4.0, the same as A1200KBv2, whose FFC footprint this reuses. See LICENSE.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3 |
| 2 | 100 | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2 |
| 2 | PESD5V0S1BA | Diode_SMD:D_SOD-323 | D1, D2 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | 150 | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | ATmega4809 | Package_QFP:TQFP-48_7x7mm_P0.5mm | U1 |
| 1 | Amiga keyboard | A1200KB:DIN-5_180deg_DIN-504_Horizontal | J3 |
| 1 | KB FFC | Amiga_FFC:FFC-1.25mm-RA-5204403245 | J1 |
| 1 | LED HDR (symmetric) | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Horizontal | J2 |
| 1 | UPDI | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |

steveed/a1200kb-external-case
Some ideas for using an external Amiga keyboard with an A1200 in a desktop or tower case.

steveed/a1200kb-external-case
Some ideas for using an external Amiga keyboard with an A1200 in a desktop or tower case.


MF-Room/mseq_pcb
KiCad 10 hardware design for MSeq embedded, the microcontroller implementation of the MSeq MIDI sequencer.




noahzhy/cc_glasses
tools/ 为此次整改的重建和检查脚本;日常直接编辑 KiCad 工程。重建脚本会覆盖设计,不能在人工修改后直接重跑。Python 工具不引入继承类;需要 KiCad 10 的 pcbnew Python,以及 Python 3 的 sexpdata、numpy、scipy、shapely、pymupdf。


10htts/5S-Blower-Controller
Open-source reference controller for a two-wire brushed-DC blower powered by a removable 5-series lithium-ion battery (approximately 15–21 V).
It measures 75.1 × 29.6 mm and has 2 copper layers, 1.6 mm thick.
18 parts, built around the ATMEGA4809-AF, CC0603KRX7R9BB104, PESD5V0S1BA,115-MS and CL21A106KAYNNNE. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the steveed/a1200kb-external-case repository on GitHub, at the commit this page was made from: the board is encoder/A1200KB-Encoder.kicad_pcb and its schematic adapter/A1200KB-DB37.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask steveed before reusing the design.