

KakuteHAT v2
Useful Raspberry Pi HATs for ArduPilot
- Size
- 65 × 56 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 50
- Nets
- 40
- Pads
- 217
- Tracks, vias
- 439, 24
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 8 May 2019
- Updated
- 22 Sep 2024
Overview
KakuteHAT v2 is an open-source printed circuit board by stephendade, from the stephendade/AP-HAT repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 65 × 56 mm with 50 parts on 40 nets, routed with 439 tracks and 24 vias.
It is built around the TPS54331DR-JSM, CAT24C32LI- and NC7SZ00P5X, with the TPS22810DBV, DMG2305UX and DMMT5401 among its other parts. Its parts include 11 resistors, 10 connectors, 9 capacitors, 6 ICs and 3 diodes.
Main components
7TPS54331DR-JSM
SOP-8-40℃~+125℃ 1 2mA 3A 4.5V~40V 400kHz Adjustable Buck Built-in No Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting Step-down type SOP-8 DC-DC Converters ROHSJSMSEMIDC-DC ConvertersCAT24C32LI-
PDIP-8-40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 100 Years 1MHz 2mA 3.5us 32Kbit 5ms 5uA Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C PDIP-8 EEPROM ROHSonsemiEEPROMNC7SZ00P5X
SC-70-5Logic GatesTECH PUBLICTPS22810DBV
SOT-23-6-40℃~+105℃ 1 2.7V~18V 2A 79mΩ Active High Load Switch Undervoltage Protection(UVP)、Over Temperature Protection SOT-23-6 Power Distribution Switches ROHSTexas InstrumentsPower Distribution SwitchesDMG2305UX
SOT-23-55℃~+150℃ 1 P-Channel 1.7W 190pF 1V 20V 4.1A 52mΩ@4.5V 7.8nC 740pF P-Channel SOT-23 MOSFETs ROHSTECH PUBLICMOSFETsDMMT5401
SOT-26(SC74R)-55℃~+150℃ 150V 2 PNP 200mA 200mV 300MHz 300mW 50uA 5V 60 PNP SOT-26(SC74R) Bipolar (BJT) ROHSDiodes IncorporatedBipolar (BJT)PDS560-13-FS
TO-277BTO-277B Schottky Diodes ROHSFUXINSEMISchottky Diodes
README
README.mdAP-HAT: Useful Raspberry Pi HATs for ArduPilot
This repository contains 3x archived hardware PCB designs for Raspberry Pi HAT's, created in KiCAD.
[!NOTE] These boards are retired and their designs not will be be maintained into the future
Pi-Kakute
The Kakute HAT is an expansion board for the Raspberry Pi, which allows a KakuteF4 (non-AIO) to be interfaced (send telemetry to the Pi). Additionally, it contains breakout ports for RC In, GPS, Servo Out and others.
It contains a 5V, 2.5A power supply for the Raspberry Pi and has power switches for both the Kakute and Pi.
AP-HAT 1
A forerunner of the Pi-Connect Lite V1 series. It features many useful connectivity options and a robust power supply:
- 7-30V, 3.5A power supply for the Raspberry Pi
- Power button for safe shutdown of the Pi
- Voltage monitoring (both input voltage and 5V rail) via ADC
- 3x ADC channels
- 3x Telementry ports (UART). 1x unpowered, 1x powered at 3.3V and 1x powered at 5V
- Reverse voltage and ESD protected
Pi-Connect Lite
The V1.x series of the Pi-Connect Lite, as previously sold on the Rpanion Electronics webstore. It features:
- High current power supply (7-30V input, 5.1V/3.5A output)
- 1x Telemetry (serial) port using a JST-GH 6-pin Dronecode standard connector
- Additional UART port (Pi 4 only) (Version 1.4+)
See the product manual for full details.
Parts
50| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 3.9K | Resistor_SMD:R_0603_1608Metric | R1, R2, R6, R7 |
| 4 | 3mm_Mounting_Hole | MountingHole:MountingHole_3.2mm_M3_ISO7380 | H2, H3, H4, H5 |
| 3 | 10K | Resistor_SMD:R_0603_1608Metric | R3, R5, R11 |
| 2 | 1.0UF-50V | Capacitor_SMD:C_0805_2012Metric | C3, C4 |
| 1 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C8 |
| 1 | 1.5nF, 50V | Capacitor_SMD:C_0402_1005Metric | C10 |
| 1 | 1.96K | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 10.2K | Resistor_SMD:R_0402_1005Metric | R9 |
| 1 | 100uF | Capacitor_SMD:C_1210_3225Metric | C9 |
| 1 | 10uF, 50V | Capacitor_SMD:C_1206_3216Metric | C6 |
| 1 | 10uH | Inductor_SMD:L_10.4x10.4_H4.8 | L1 |
| 1 | 2.2UF-25V | Capacitor_SMD:C_0805_2012Metric | C7 |
| 1 | 30V | Diode_SMD:D_SMA | D1 |
| 1 | 30pF, 25V | Capacitor_SMD:C_0402_1005Metric | C11 |
| 1 | 36.5k | Resistor_SMD:R_0402_1005Metric | R10 |
| 1 | 40HAT | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J1 |
| 1 | 47K | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 8.2nF | Capacitor_SMD:C_0402_1005Metric | C5 |
| 1 | CAT24C32 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | CameraHole | MountingHole:MountingHole_2.2mm_M2_ISO7380 | H1 |
| 1 | DMG2305UX | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | DMMT5401 | Package_TO_SOT_SMD:SOT-23-6_Handsoldering | Q1 |
| 1 | D_Schottky | Diode_SMD:D_2010_5025Metric | D2 |
| 1 | EEPROM_W | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | Ext_Switch | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J10 |
| 1 | FC_Socket | Connector_PinSocket_2.54mm:PinSocket_1x09_P2.54mm_Vertical | J12 |
| 1 | FC_Socket2 | Connector_PinHeader_2.54mm:PinHeader_2x09_P2.54mm_Vertical | J9 |
| 1 | GPS2 | Connector_JST:JST_GH_SM06B-GHS-TB_1x06-1MP_P1.25mm_Horizontal | J7 |
| 1 | I2C | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | Kakute Power Switch | Button_Switch_THT:SW_CuK_OS102011MA1QN1_SPDT_Angled | SW1 |
| 1 | KakuteF4_V2 | Kakute:Kakute F4 V2_NoPin | U3 |
| 1 | Mout | Kakute:PinHeader_4x03_P2.54mm_Horizontal | J4 |
| 1 | NC7SZ00P5X | Silicon-Standard:SC70 | U5 |
| 1 | PDS560-13 | PowerDI:POWERDI5 | D3 |
| 1 | Pi Power Switch | Button_Switch_THT:SW_CuK_OS102011MA1QN1_SPDT_Angled | SW2 |
| 1 | Power_Pad | Connector_Molex:Molex_Nano-Fit_105313-xx02_1x02_P2.50mm_Horizontal | J8 |
| 1 | RC_IN | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | J6 |
| 1 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged2Bar12_Pad1.0x1.5mm | JP1 |
| 1 | TPS22810 | Package_TO_SOT_SMD:SOT-23-6_Handsoldering | U1 |
| 1 | TPS54331DR | Package_SO:TI_SO-PowerPAD-8 | U4 |
| 1 | TPS709 | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U2 |
More from stephendade/AP-HAT
2- 2 layers65 × 30.5 mm

- 2 layers65 × 30.5 mm

Similar boards
- 4 layers200 × 100 mm

Heteromycin
hasenbanck/heteromycin
A 3D printer board using a powerfull STM32 MCU, TMC5160/TMC2160 driver and a Raspberry Pi or compatible SBC
373 parts40 - 2 layers65 × 56 mm

- 2 layers65 × 56 mm

- 2 layers65 × 56 mm

- 2 layers182.5 × 65 mm

V1Panel
pilotniq/MJoulnir
Hardware and software for the control system of a full size electric boat.
171 parts2 - 2 layers65 × 56 mm

ACYONP SMD LCSC
SkullKill/ACYONP-PCB
PCB for Access Control Yubikey OTP NFC Pi (ACYONP). For Raspberry Pi. This is a Door Access Control using Electronic Door Strike, with Yubikey OTP via NFC / KeyPad / WebInterface for Authentication.
93 parts1GPL-3.0 - 4 layers65 × 56 mm

- 4 layers65 × 56 mm

Questions
How big is the KakuteHAT v2 PCB?
It measures 65 × 56 mm and has 2 copper layers, 1.6 mm thick.
What parts does the KakuteHAT v2 use?
50 parts, built around the TPS54331DR-JSM, CAT24C32LI-, NC7SZ00P5X and TPS22810DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the KakuteHAT v2 KiCad files?
From the stephendade/AP-HAT repository on GitHub, at the commit this page was made from: the board is Pi-Kakute/KakuteHAT_v2.kicad_pcb and its schematic Pi-Connect Lite/PiConnectLite.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the KakuteHAT v2 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).