Skip to the content
2 layers159.5 × 39 mmSection GPWS, the printed circuit board in 3D

Complete project for the Airbus A319/320/321/330 OverHead Panel

Size
159.5 × 39 mm
Copper layers
2
Thickness
1.6 mm
Parts
38
Nets
43
Pads
102
Tracks, vias
208, 18
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
2 Dec 2024
Updated
29 Sep 2026

Overview

Section GPWS is an open-source printed circuit board by stefanofinetti, from the stefanofinetti/MF_OverHead_Panel repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 159.5 × 39 mm with 38 parts on 43 nets, routed with 208 tracks and 18 vias.

It is built around the M2.5. Its parts include 15 diodes, 5 resistors, 4 switches and 2 connectors.

Main components

1

README

Section_EXTLT/README.md

EXT LT section board (v2)

The v2 board under the EXT LT panel. It carries the panel's switches, annunciator LEDs and backlight, at their v1 positions, and reaches the mainboard through one ribbon and one pair of backlight wires. There are no ICs on it. The design rules shared by the eight section boards are in docs/board-split.md.

  • PCB: 159.5 × 79.5 mm, 2 layers, 1.6 mm. Every v1 hole is kept.
  • Status: routed with Freerouting. ERC, DRC and schematic parity are clean. Not yet ordered.

EXT LT board, 3D view

Top, the panel side:

EXT LT, top

Bottom, with the connectors:

EXT LT, bottom

Rendered by KiCad from the board file. The bottom is seen from below, so it is mirrored against the top.

Connectors

Both are new on v2 and sit on the back, so nothing new stands proud of the front.

RefWhatGoes to
J1Shrouded IDC header, 14 pins, SMDJ706 on the mainboard, straight ribbon, pin 1 to pin 1
J2JST PH, 2 pins, SMD. Pin 1 +9V_BL (+), pin 2 the switched return (−)screw terminal J606 on the mainboard

J1 and J2 are at the right, over the mainboard, above its TLC5927 block.

The signal on every ribbon pin is in the design document: EXT LT — 14 pins.

Switches

RefSwitchTypev1 ref
SW1EXTLT STROBEtoggleS7
SW2EXTLT BEACONtoggleS6
SW3EXTLT WINGtoggleS5
SW4EXTLT NAV & LOGOtoggleS4
SW5EXTLT RWY TURNtoggleS8
SW6EXTLT LDG LIGHT LtoggleS1
SW7EXTLT LDG LIGHT RtoggleS2
SW8EXTLT NOSE LIGHTtoggleS3

Backlight

31 LEDs, 1206 (D1–D31), on 9 V: 15 strings of two with 150 Ω, and one single LED with R16, 330 Ω. Each string runs at about 17 mA. K marks every cathode on the silkscreen.

Assembly notes

  • No annunciators, so the ribbon carries no +5V_LED.
  • Toggles: ON-OFF-ON for LDG LIGHT L, LDG LIGHT R, NOSE LIGHT and NAV & LOGO, read on both contacts (1 and 3); ON-OFF for STROBE, BEACON, WING and RWY TURN, read on contact 1. Lever up closes contact 1, the lower pin. They are generic three-terminal PCB-pin lever toggles from AliExpress, fitted by hand. The footprint is the v1 one, whose name still carries the E-Switch number 100SP1T1B4M2QE: that is not the part fitted, and the schematic gives the toggles no part number.
  • D31 is a single-LED string: on v1 it was paired with D139, now on GPWS. R16, 330 Ω on the back, gives it the same 17 mA as a pair on 150 Ω.
  • Every part has its value, polarity or pin 1 on the silkscreen of its own side. Each part's description in the schematic names its v1 reference.

Parts

38
QtyValueFootprintReferences
9LEDLED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolderD7, D8, D9, D10, D11, D12, D13, D14, D15
8M2.5MountingHole:MountingHole_2.7mm_M2.5H5, H6, H7, H8, H9, H10, H11, H12
4150Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1, R2, R3, R4
4M3MountingHole:MountingHole_3.2mm_M3_DIN965_Pad_TopBottomH1, H2, H3, H4
4whiteOVHD:LED_Rectangular_W3.9mm_H1.8mm_FlatTopD2, D4, D5, D6
2amberOVHD:LED_Rectangular_W3.9mm_H1.8mm_FlatTopD1, D3
1330Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR5
1BacklightConnector_JST:JST_PH_B2B-PH-SM4-TB_1x02-1MP_P2.00mm_VerticalJ2
1GPWS G/S MODEOVHD:G-Switch_PS-7054DVB-6PNSW3
1GPWS LDG FLAPS 3OVHD:G-Switch_PS-7054DVB-6PNSW4
1GPWS SYSOVHD:G-Switch_PS-7054DVB-6PNSW2
1GPWS TERROVHD:G-Switch_PS-7054DVB-6PNSW1
1GPWS ribbonConnector_IDC:IDC-Header_2x07_P2.54mm_Vertical_SMDJ1

More from stefanofinetti/MF_OverHead_Panel

9
  • 4 layers313 × 206 mmOverHead v1, the printed circuit board in 3D

    OverHead v1

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    416 parts5GPL-3.0
  • 2 layers137 × 89 mmOVHD Mainboard, the printed circuit board in 3D

    OVHD Mainboard

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    127 parts5GPL-3.0
  • 2 layers159.5 × 79.5 mmSection EXTLT, the printed circuit board in 3D

    Section EXTLT

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    61 parts5GPL-3.0
  • 2 layers108.5 × 79.5 mmSection SIGNS, the printed circuit board in 3D

    Section SIGNS

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    57 parts5GPL-3.0
  • 2 layers177.5 × 40 mmSection FUEL, the printed circuit board in 3D

    Section FUEL

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    55 parts5GPL-3.0
  • 2 layers150.5 × 39 mmSection AIRCOND, the printed circuit board in 3D

    Section AIRCOND

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    46 parts5GPL-3.0
  • 2 layers132.5 × 81.5 mmSection ADIRS, the printed circuit board in 3D

    Section ADIRS

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    41 parts5GPL-3.0
  • 2 layers177.5 × 39.5 mmSection ELEC, the printed circuit board in 3D

    Section ELEC

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    35 parts5GPL-3.0
  • 2 layers39 × 79.5 mmSection APU, the printed circuit board in 3D

    Section APU

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    24 parts5GPL-3.0

Similar boards

  • 2 layers40.9 × 85 mmStudio mic, the printed circuit board in 3D

    Studio mic

    Spirit532/studio_mic

    A simple, easy to build preamplifier for any true condenser capsule, to make a condenser microphone

    63 parts150MIT
  • 2 layers65 × 56 mmPi1541io, the printed circuit board in 3D

    Pi1541io

    hackup/Pi1541io

    Raspberry Pi extension board for the PI1541 project.

    57 parts109CC-BY-SA-4.0
  • 2 layers65 × 56 mmClumsyMIDI, the printed circuit board in 3D

    ClumsyMIDI

    gmcn42/clumsyMIDI

    A THT-only Raspberry Pi expansion board containing a MIDI interface, DAC, and OLED display

    26 parts90CC-BY-SA-4.0
  • 6 layers203 × 151.8 mmPDNode Baseboard, the printed circuit board in 3D

    PDNode Baseboard

    DvidMakesThings/HW_PDNode-600-Pro

    The PDNode-600 is a professional-grade, 600W USB Power Delivery Unit designed specifically for compact 10-inch rack systems, targeting embedded developers, homelab enthusiasts, test benches, and smart infrastructure.

    236 parts86AGPL-3.0
  • 4 layers60 × 127 mmOpenHT RF, the printed circuit board in 3D

    OpenHT RF

    M17-Project/OpenHT-hw

    Repository for the hardware parts of the OpenHT project

    199 parts63
  • 2 layers85 × 56.5 mmModemHAT, the printed circuit board in 3D

    ModemHAT

    astuder/ModemHAT

    Classic Phone Modem HAT for the Raspberry Pi

    111 parts56
  • 4 layers70 × 60 mmMarelleo, the printed circuit board in 3D

    Marelleo

    Zebra-Rodeo/marelleo

    Une boîte qui raconte une histoire quand on pose une figurine dessus. Boîtier, carte, micrologiciel et doc pour la refaire.

    57 parts47
  • 2 layers285.8 × 124.6 mmPunk75, the printed circuit board in 3D

    Punk75

    dsanchezseco/punk75

    Ortholinear keyboard with 75 keys and all components through hole

    194 parts44GPL-3.0

Questions

How big is the Section GPWS PCB?

It measures 159.5 × 39 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Section GPWS use?

38 parts, built around the M2.5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Section GPWS KiCad files?

From the stefanofinetti/MF_OverHead_Panel repository on GitHub, at the commit this page was made from: the board is Section_GPWS/Section_GPWS.kicad_pcb and its schematic Kicad Files/OverHead_v1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Section GPWS design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).