Skip to the content
2 layers159.5 × 79.5 mmSection EXTLT, the printed circuit board in 3D

Complete project for the Airbus A319/320/321/330 OverHead Panel

Size
159.5 × 79.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
61
Nets
54
Pads
148
Tracks, vias
315, 35
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
2 Dec 2024
Updated
29 Sep 2026

Overview

Section EXTLT is an open-source printed circuit board by stefanofinetti, from the stefanofinetti/MF_OverHead_Panel repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 159.5 × 79.5 mm with 61 parts on 54 nets, routed with 315 tracks and 35 vias.

It is built around the 100SP1T1B4M2QE. Its parts include 31 diodes, 16 resistors, 8 switches and 2 connectors.

Main components

1

README

Section_EXTLT/README.md

EXT LT section board (v2)

The v2 board under the EXT LT panel. It carries the panel's switches, annunciator LEDs and backlight, at their v1 positions, and reaches the mainboard through one ribbon and one pair of backlight wires. There are no ICs on it. The design rules shared by the eight section boards are in docs/board-split.md.

  • PCB: 159.5 × 79.5 mm, 2 layers, 1.6 mm. Every v1 hole is kept.
  • Status: routed with Freerouting. ERC, DRC and schematic parity are clean. Not yet ordered.

EXT LT board, 3D view

Top, the panel side:

EXT LT, top

Bottom, with the connectors:

EXT LT, bottom

Rendered by KiCad from the board file. The bottom is seen from below, so it is mirrored against the top.

Connectors

Both are new on v2 and sit on the back, so nothing new stands proud of the front.

RefWhatGoes to
J1Shrouded IDC header, 14 pins, SMDJ706 on the mainboard, straight ribbon, pin 1 to pin 1
J2JST PH, 2 pins, SMD. Pin 1 +9V_BL (+), pin 2 the switched return (−)screw terminal J606 on the mainboard

J1 and J2 are at the right, over the mainboard, above its TLC5927 block.

The signal on every ribbon pin is in the design document: EXT LT — 14 pins.

Switches

RefSwitchTypev1 ref
SW1EXTLT STROBEtoggleS7
SW2EXTLT BEACONtoggleS6
SW3EXTLT WINGtoggleS5
SW4EXTLT NAV & LOGOtoggleS4
SW5EXTLT RWY TURNtoggleS8
SW6EXTLT LDG LIGHT LtoggleS1
SW7EXTLT LDG LIGHT RtoggleS2
SW8EXTLT NOSE LIGHTtoggleS3

Backlight

31 LEDs, 1206 (D1–D31), on 9 V: 15 strings of two with 150 Ω, and one single LED with R16, 330 Ω. Each string runs at about 17 mA. K marks every cathode on the silkscreen.

Assembly notes

  • No annunciators, so the ribbon carries no +5V_LED.
  • Toggles: ON-OFF-ON for LDG LIGHT L, LDG LIGHT R, NOSE LIGHT and NAV & LOGO, read on both contacts (1 and 3); ON-OFF for STROBE, BEACON, WING and RWY TURN, read on contact 1. Lever up closes contact 1, the lower pin. They are generic three-terminal PCB-pin lever toggles from AliExpress, fitted by hand. The footprint is the v1 one, whose name still carries the E-Switch number 100SP1T1B4M2QE: that is not the part fitted, and the schematic gives the toggles no part number.
  • D31 is a single-LED string: on v1 it was paired with D139, now on GPWS. R16, 330 Ω on the back, gives it the same 17 mA as a pair on 150 Ω.
  • Every part has its value, polarity or pin 1 on the silkscreen of its own side. Each part's description in the schematic names its v1 reference.

Parts

61
QtyValueFootprintReferences
31LEDLED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolderD1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +15
15150Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11, R12, R13, R14, R15
4M3MountingHole:MountingHole_3.2mm_M3_DIN965_Pad_TopBottomH1, H2, H3, H4
1330Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR16
1BacklightConnector_JST:JST_PH_B2B-PH-SM4-TB_1x02-1MP_P2.00mm_VerticalJ2
1EXTLT BEACONOVHD:Toggle_Switch_100SP1T1B4M2QESW2
1EXTLT LDG LIGHT LOVHD:Toggle_Switch_100SP1T1B4M2QESW6
1EXTLT LDG LIGHT ROVHD:Toggle_Switch_100SP1T1B4M2QESW7
1EXTLT NAV & LOGOOVHD:Toggle_Switch_100SP1T1B4M2QESW4
1EXTLT NOSE LIGHTOVHD:Toggle_Switch_100SP1T1B4M2QESW8
1EXTLT RWY TURNOVHD:Toggle_Switch_100SP1T1B4M2QESW5
1EXTLT STROBEOVHD:Toggle_Switch_100SP1T1B4M2QESW1
1EXTLT WINGOVHD:Toggle_Switch_100SP1T1B4M2QESW3
1EXTLT ribbonConnector_IDC:IDC-Header_2x07_P2.54mm_Vertical_SMDJ1

More from stefanofinetti/MF_OverHead_Panel

9
  • 4 layers313 × 206 mmOverHead v1, the printed circuit board in 3D

    OverHead v1

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    416 parts5GPL-3.0
  • 2 layers137 × 89 mmOVHD Mainboard, the printed circuit board in 3D

    OVHD Mainboard

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    127 parts5GPL-3.0
  • 2 layers108.5 × 79.5 mmSection SIGNS, the printed circuit board in 3D

    Section SIGNS

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    57 parts5GPL-3.0
  • 2 layers177.5 × 40 mmSection FUEL, the printed circuit board in 3D

    Section FUEL

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    55 parts5GPL-3.0
  • 2 layers150.5 × 39 mmSection AIRCOND, the printed circuit board in 3D

    Section AIRCOND

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    46 parts5GPL-3.0
  • 2 layers132.5 × 81.5 mmSection ADIRS, the printed circuit board in 3D

    Section ADIRS

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    41 parts5GPL-3.0
  • 2 layers159.5 × 39 mmSection GPWS, the printed circuit board in 3D

    Section GPWS

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    38 parts5GPL-3.0
  • 2 layers177.5 × 39.5 mmSection ELEC, the printed circuit board in 3D

    Section ELEC

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    35 parts5GPL-3.0
  • 2 layers39 × 79.5 mmSection APU, the printed circuit board in 3D

    Section APU

    stefanofinetti/MF_OverHead_Panel

    Complete project for the Airbus A319/320/321/330 OverHead Panel

    24 parts5GPL-3.0

Similar boards

  • 4 layers117.7 × 100.9 mmShield, the printed circuit board in 3D

    Shield

    adamgreen/rugrover

    A Work In Progress: My modern interpretation of the Rug Warrior Pro

    46 parts1
  • 2 layers59.1 × 101.4 mmFlight computer, the printed circuit board in 3D

    Flight computer

    nakujaproject/N3FlightComputer-PCB

    Electrical schematics and PCB for N3 flight computer

    48 parts1MIT
  • 2 layers715.5 × 705.5 mmFrontpanel, the printed circuit board in 3D

    Frontpanel

    Pconst167/sol-1

    Sol-1 is a homebrew CPU and Minicomputer built from 74HC logic. It is published here for educational purposes.

    299 parts1
  • 2 layers152.9 × 93.6 mmController, the printed circuit board in 3D

    Controller

    dst5rfcar/Controller_Pcb

    67 parts
  • 2 layers116.5 × 47.5 mmProj3 potencia, the printed circuit board in 3D

    Proj3 potencia

    Edson8101/EA801---Turma-D

    Este repositório apresenta os projetos desenvolvidos pelos estudantes da FEEC-UNICAMP na disciplina de graduação denominada Laboratório de Sistemas Embarcados.

    27 partsMIT
  • 14 layers260.2 × 212.8 mmAutomation, the printed circuit board in 3D

    Automation

    jeshinbabu27/pcb-with-realy-final

    258 parts
  • 4 layers113.1 × 57 mmProjet, the printed circuit board in 3D

    Projet

    karimabdellaziz/Projet-robot-carte-PCB

    74 parts

Questions

How big is the Section EXTLT PCB?

It measures 159.5 × 79.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Section EXTLT use?

61 parts, built around the 100SP1T1B4M2QE. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Section EXTLT KiCad files?

From the stefanofinetti/MF_OverHead_Panel repository on GitHub, at the commit this page was made from: the board is Section_EXTLT/Section_EXTLT.kicad_pcb and its schematic Kicad Files/OverHead_v1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Section EXTLT design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).