
Tinynode
Stary2001/my-mesh-nodes
Here's all my mesh stuff. Everything here is licensed under CERN OHL-P.

Here's all my mesh stuff. Everything here is licensed under CERN OHL-P.
Ebyte e80-22-zero is an open-source printed circuit board by Stary2001, from the Stary2001/my-mesh-nodes repository on GitHub, published under the CERN-OHL-P-2.0 licence. It is a 2-layer board of 65 × 30 mm with 18 parts on 43 nets, routed with 127 tracks and 70 vias.
It is built around the CAT24C256LI. Its parts include 5 connectors, 4 resistors, 2 capacitors and 2 ICs.
Here's all my mesh stuff. Everything here is licensed under CERN OHL-P.
Tested, works (as much as STM32 can).
Tested, works. See here for documentation.
Tested, works. See here for documentation.
Untested. Use at your own risk.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole_2.7mm_M2.5 | MountingHole:MountingHole_2.7mm_M2.5 | MH1, MH2, MH3, MH4 |
| 2 | 0 | Resistor_SMD:R_0402_1005Metric | R3, R4 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | Conn_Coaxial | Connector_Coaxial:SMA_Amphenol_901-144_Vertical | J4, J5 |
| 1 | 100n | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 22u | Capacitor_SMD:C_1206_3216Metric | C2 |
| 1 | CAT24C256 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | Conn_01x02_Pin | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J1 |
| 1 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | E80-xxxM2213S | stary:E80-xxxM2213S | U2 |
| 1 | GPIO | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J3 |
| 1 | ID_WP | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |

Stary2001/my-mesh-nodes
Here's all my mesh stuff. Everything here is licensed under CERN OHL-P.

Stary2001/my-mesh-nodes
Here's all my mesh stuff. Everything here is licensed under CERN OHL-P.

Stary2001/my-mesh-nodes
Here's all my mesh stuff. Everything here is licensed under CERN OHL-P.

Stary2001/my-mesh-nodes
Here's all my mesh stuff. Everything here is licensed under CERN OHL-P.

Stary2001/my-mesh-nodes
Here's all my mesh stuff. Everything here is licensed under CERN OHL-P.

Stary2001/my-mesh-nodes
Here's all my mesh stuff. Everything here is licensed under CERN OHL-P.






eamars/RaspberryPi-Pico-Motor-Expansion-Board
A raspberry pi pico expansion board designed for OpenTrickler project
nullstalgia/NullWiiCon
AVR Firmware to convert Nintendo Extension port controllers to USB for use on Switch and PC

bmo/tuning-knob-pcboard
KiCAD PC Board design for a tuning knob that works with Flex Radio SmartSDR, PowerSDR, and RHR. Uses STM32 hardware.
It measures 65 × 30 mm and has 2 copper layers, 1.6 mm thick.
18 parts, built around the CAT24C256LI. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Stary2001/my-mesh-nodes repository on GitHub, at the commit this page was made from: the board is hardware/ebyte-e80-22-zero/ebyte-e80-22-zero.kicad_pcb and its schematic hardware/1x-lipo-board/1s-lipo-board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CERN-OHL-P-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).