

Block esp32c3
- Size
- 40 × 40 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 31
- Nets
- 28
- Pads
- 128
- Tracks, vias
- 204, 27
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 31 May 2025
- Updated
- 31 May 2025
Overview
Block esp32c3 is an open-source printed circuit board by Stary2001, from the Stary2001/blocks repository on GitHub. It is a 2-layer board of 40 × 40 mm with 31 parts on 28 nets, routed with 204 tracks and 27 vias.
It is built around the ESP32-C3-WROOM-02-H4 and CIGT201610LH2R2MNE. Its parts include 11 resistors, 5 capacitors, 5 connectors, 2 ICs and 2 diodes. It belongs with the ESP32 and RISC-V boards of this library.
Main components
2ESP32-C3-WROOM-02-H4
SMD,20x18mm-105dBm -40℃~+105℃ 2.4GHz 20.5dBm 345mA 3V~3.6V 82mA Bluetooth5.0 ESP32-C3 On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,20x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesCIGT201610LH2R2MNE
08061.8A 116mΩ 2.2uH 2.3A ±20% 0806 Power Inductors ROHSSamsung Electro-MechanicsPower Inductors
README
README.mdHardware Blocks
great idea dont steal
How to block?
- 40x40mm, round the corners if you can plz.
- If not, at least get it roughly in 10x10mm grid
- Use 2.5mm pitch JST-XH (clone) headers - 2pin for power, 4pin for I2C.
- For i2c: Qwiic pinout - GND VCC (3.3-5v) SDA SCL
- For UART: ?
- for power: VCC then GND
- Either I get this right or I have to repin all my cables when they come in. Ah well.
- KiCad footprint Connector_JST:JST_XH_S4B-XH-A_1x04_P2.50mm_Horizontal
- 4x M3 mounting holes in the corners with 30x30mm between holes
- KiCad footprint MountingHole:MountingHole_3.2mm_M3_Pad
ESP32C3 block
- Done
- It's an ESP32. What more do you want?
- 5v->3.3 buck I guess
Buck block
- Done (?)
- 24V input, 85% Vin output
- 5v->3.3
- Programmable output voltage - see https://www.ti.com/lit/an/slyt777/slyt777.pdf
- Defaults to 5v
INA3221 block
- Done
- I2C voltage and current sensor.
Voltmeter block
- Not yet
- Uses https://www.digikey.co.uk/en/products/detail/mornsun-america-llc/IB0505S-W75R3/16571441 to get an isolated (!) supply
- maybe
- Whack in a 16bit ADC and some op amps, gg ez
- i2c isolator. how
- ch32v003 cant split tx/rx :(
- samd11 has 4-wire i2c
- we can just simply tm use sda_out to drive an optoisolator
- or get ISO1641BDR
- idk
- power isolation
- Choose some random dcdc: https://www.digikey.co.uk/en/products/detail/mornsun-america-llc/IB0505S-W75R3/16571441
USB switch block
- Done
- Can run off a potato
- gets 5v from either the i2c connector, or either of the usb-c host connectors
- Switches one USB-A device between two hosts, with corresponding power.
- Just replace the diodes with links if you have issues I guess, idk
Parts
31| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad | H1, H2, H3, H4 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric | R7, R8, R11 |
| 3 | 10u | Capacitor_SMD:C_0603_1608Metric | C1, C2, C5 |
| 2 | 5k1 | Resistor_SMD:R_0603_1608Metric | R4, R5 |
| 2 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4, J5 |
| 2 | Conn_01x04_Pin | Connector_JST:JST_XH_S4B-XH-A_1x04_P2.50mm_Horizontal | J1, J2 |
| 2 | LED_Small | Diode_SMD:D_0603_1608Metric | D1, D2 |
| 2 | R_Small | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | enough | Resistor_SMD:R_0603_1608Metric | R9, R10 |
| 1 | 100n | Capacitor_SMD:C_0603_1608Metric | C4 |
| 1 | 150k | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 1u | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | 33.2k | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | CIGT201610LH2R2MNE | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | ESP32-C3-WROOM-02 | RF_Module:ESP32-C3-WROOM-02 | U1 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | TLV62568DDC | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J3 |
More from Stary2001/blocks
3- 4 layers40 × 40 mm

- 2 layers40 × 40 mm

- 2 layers30 × 50 mm

Similar boards
- 2 layers131.1 × 149.9 mm

HEDC B001
Thaddeus-Maximus/dotclock
An ESP32-based alarm clock with a dot matrix LED display, rotary encoder interface, MP3 audio playback, and a web configuration UI.
70 parts - 2 layers155.5 × 130 mm

Einkpicframe
Spritetm/picframe_colepd
A WiFi picture frame allowing for remote photo uploads, using an ESP32-C3 and a 5.6" color E-ink display
60 parts97 - 2 layers18 × 14.4 mm

- 2 layers60 × 30 mm

- 2 layers88.6 × 30 mm

- 2 layers79.9 × 36.2 mm

Desk display
nepyope/Project-Homunculus
Project Homunculus is open-source, low-cost hardware for capturing human hand and arm motions. It has two parts.
63 parts51 - 2 layers76.8 × 23.5 mm

SommerESP
exico91/SommerESP
A plug and play ESP32-C3 board to control Sommer garage doors
41 parts29MIT - 2 layers51 × 71 mm

Questions
How big is the Block esp32c3 PCB?
It measures 40 × 40 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Block esp32c3 use?
31 parts, built around the ESP32-C3-WROOM-02-H4 and CIGT201610LH2R2MNE. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Block esp32c3 KiCad files?
From the Stary2001/blocks repository on GitHub, at the commit this page was made from: the board is esp32c3/v0/block-esp32c3.kicad_pcb and its schematic buck/v0/block-buck.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Block esp32c3 design in my own project?
Its repository states no licence, so its author keeps all rights: ask Stary2001 before reusing the design.