

TimekillerXtreme
Hardware part of the SDA Project.
- Size
- 61.5 × 105.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 114
- Nets
- 120
- Pads
- 425
- Tracks, vias
- 2,959, 150
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 30 Oct 2018
- Updated
- 4 Sep 2026
Overview
TimekillerXtreme is an open-source printed circuit board by stanislavbrtna, from the stanislavbrtna/SDA_Wonder_HW repository on GitHub. It is a 2-layer board of 61.5 × 105.3 mm with 114 parts on 120 nets, routed with 2,959 tracks and 150 vias.
It is built around the STM32F407VGT6, FT230XS-R and NCP1529ASN, with the USBLC6-4, AOZ1310CI-1 and MCP73831 among its other parts. Its parts include 30 capacitors, 24 resistors, 17 connectors, 9 ICs and 8 switches. It belongs with the STM32 boards of this library.
Main components
9STM32F407VGT6
LQFP-100(14x14)-40℃~+85℃ 1.8V~3.6V 12bit 12bit 168MHz 192KB 1MB 32 Bit 82 ARM Cortex-M4 Built-in FLASH LQFP-100(14x14) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)FT230XS-R
SSOP-16-150mil-40℃~+85℃ 125uA 3.3V~5V 8mA USB 2.0 USB to UART SSOP-16-150mil USB Converters ROHSFTDIUSB ConvertersNCP1529ASN
TSOP-5-40℃~+85℃ 1 1.7MHz 1A 2.7V~5.5V 28uA 900mV~3.9V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting Step-down type Yes TSOP-5 DC-DC Converters ROHSonsemiDC-DC ConvertersUSBLC6-4
UncategorisedSTMicroelectronicsAOZ1310CI-1
SOT-23-5-40℃~+85℃ 1 2.7V~5.5V 80mΩ Active High High Side Switch SOT-23-5 Power Distribution Switches ROHSAlpha & Omega SemiconductorPower Distribution SwitchesMCP73831
UncategorisedMicrochip TechnologyTLV431ASN
TSOP-5-1.5mm-40℃~+85℃@(Ta) 1.24V~16V 150nA 20mA 80uA Adjustable Parallel ±1% TSOP-5-1.5mm Voltage Reference ROHSonsemiVoltage ReferenceIRLML6302
SOT-23-55℃~+150℃ 1 P-Channel 1.5V 2.4nC@4.5V 20V 28pF 53pF 540mW 600mΩ@4.5V 780mA 97pF P-Channel SOT-23 MOSFETs ROHSGuangdong HottechMOSFETsPMBT3904,215-JSM
SOT-231 NPN 200mA 200mV、300mV 250mW 300 300MHz 40V 50nA 6V NPN SOT-23 Bipolar (BJT) ROHSJSMSEMIBipolar (BJT)
README
README.mdSDA Mk. 2 Hardware Sources
In the Board directory are KiCad project files for the Boards used in the SDA and in the case Directory there are FreeCAD files for the SDA case. You can find more info about the SDA Project on its project page on hackaday.io.
Known Bugs - Rev2b (current)
- SD card slot casing is not grounded on the pcb, sd card insertion detection doesn't work because of it. This can be fixed by scraping off the protective mask near the pin and bridging ground and shielding with a bit of solder.
- Pads for battery connector are too small and can be ripped out of place when device falls form sufficient height. This is sort-of fixed with second revision of the case by giving the battery better support.
- The stacked PCBs are a point of failure, stress is built up in the connecting pins during soldering. This stress can break the contacts after few years of use, temperature changes, drops of the device. Luckily, re-soldering these pins is an easy job.
Known Bugs - Rev1
- Vcc is used as Vref, if battery goes under 3.3V, then ADC measurements are wrong.
- There is no under-voltage protection at the moment.
- There is currently no guide for battery connector alignment, if battery connector is misaligned battery doesn't make good contact.
Case R2 notes
Second revision was printed and tested. It contains optional holes for a speaker and a microphone. The add-on module and cradle works well.
Case notes
Only the 3D printable case for SDA was printed and tested, the FreeCAD file also contains drawings of a cradle and an add-on module, those are still work-in progress.
Parts
114| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 100n | Capacitors_SMD:C_0805_HandSoldering | C5, C7, C8, C13, C15, C16, C19, C20, C23, C28, C31, C32 |
| 9 | timekiller-footprints:hole-1_6-head-2_0 | , , , , , , , , | |
| 5 | 2.2u | Capacitors_SMD:C_0805_HandSoldering | C14, C21, C22, C29, C33 |
| 5 | 47k | Resistors_SMD:R_0805_HandSoldering | R7, R20, R21, R22, R23 |
| 4 | 0 | Resistors_SMD:R_0603 | R10, R11, R17, R18 |
| 4 | 10k | Resistors_SMD:R_0805_HandSoldering | R1, R12, R13, R24 |
| 4 | 4.7u | Capacitors_SMD:C_0805_HandSoldering | C3, C4, C18, C30 |
| 3 | 15k | Resistors_SMD:R_0805_HandSoldering | R2, R14, R15 |
| 3 | USBLC6 | TO_SOT_Packages_SMD:SOT-23-6_Handsoldering | U6, U8, U9 |
| 2 | 27R | Resistors_SMD:R_0805_HandSoldering | R3, R4 |
| 2 | 3.3p | Capacitors_SMD:C_0805_HandSoldering | C9, C10 |
| 2 | 47p | Capacitors_SMD:C_0805_HandSoldering | C1, C2 |
| 2 | 47u | Capacitors_SMD:C_1210_HandSoldering | C6, C17 |
| 2 | 8.2p | Capacitors_SMD:C_0805_HandSoldering | C11, C12 |
| 1 | 0 | Resistors_SMD:R_0805_HandSoldering | R19 |
| 1 | 100u | Capacitors_SMD:C_1210_HandSoldering | C24 |
| 1 | 150K | Resistors_SMD:R_0805_HandSoldering | R9 |
| 1 | 16MHz | timekiller-footprints:Crystal_SMD_HC49-HS-mini | Y2 |
| 1 | 1A | Resistors_SMD:R_0805_HandSoldering | F1 |
| 1 | 1N4148 | Diodes_SMD:D_MiniMELF | D2 |
| 1 | 220 | Resistors_SMD:R_0805_HandSoldering | R16 |
| 1 | 2k | Resistors_SMD:R_0805_HandSoldering | R5 |
| 1 | 32.768 KHz | timekiller-footprints:xtall_epso_mc146 | Y1 |
| 1 | 4.7uH | timekiller-footprints:L4x4mm | L1 |
| 1 | 470R | Resistors_SMD:R_0805_HandSoldering | R6 |
| 1 | 680K | Resistors_SMD:R_0805_HandSoldering | R8 |
| 1 | A | Buttons_Switches_THT:SW_PUSH_6mm_h5mm | SW2 |
| 1 | AOZ1310 | TO_SOT_Packages_SMD:SOT-23-5_HandSoldering | U7 |
| 1 | B | Buttons_Switches_THT:SW_PUSH_6mm_h5mm | SW3 |
| 1 | Battery | timekiller-footprints:Conn_Nokia_BL-5C | J1 |
| 1 | CHRG_LED | LEDs:LED_D3.0mm_FlatTop | D1 |
| 1 | CONN_01X03 | Pin_Headers:Pin_Header_Straight_1x03_Pitch1.27mm | J13 |
| 1 | Conn_01x02 | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.00mm | SPKR |
| 1 | Conn_Bottom_Expansion | timekiller-footprints:Pin_Header__1x06_Pitch2.54mm-NoSilk | J3 |
| 1 | Conn_Internal_Expansion | Pin_Headers:Pin_Header_Straight_2x08_Pitch1.27mm | EXP |
| 1 | Conn_LCD_Board | Pin_Headers:Pin_Header_Straight_2x10_Pitch2.00mm | J5 |
| 1 | DOWN | Buttons_Switches_THT:SW_PUSH_6mm_h5mm | SW6 |
| 1 | FT230XS-R | Housings_SSOP:SSOP-16_5.3x6.2mm_Pitch0.65mm | U2 |
| 1 | IRLML6302 | TO_SOT_Packages_SMD:SOT-23_Handsoldering | Q1 |
| 1 | LEFT | Buttons_Switches_THT:SW_PUSH_6mm_h5mm | SW4 |
| 1 | MCP73831 | TO_SOT_Packages_SMD:SOT-23-5_HandSoldering | U1 |
| 1 | NCP1529 | TO_SOT_Packages_SMD:SOT-23-5_HandSoldering | U3 |
| 1 | PD0 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J21 |
| 1 | PD1 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J20 |
| 1 | PD3 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J22 |
| 1 | PD4 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J19 |
| 1 | PE10 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J18 |
| 1 | PE11 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J23 |
| 1 | PE8 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J16 |
| 1 | PE9 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J17 |
| 1 | PMBT3904.215 | TO_SOT_Packages_SMD:SOT-23_Handsoldering | Q2 |
| 1 | PROG | Pin_Headers:Pin_Header_Straight_1x06_Pitch1.27mm | PRG |
| 1 | PWR | Buttons_Switches_THT:SW_PUSH_6mm_h5mm | SW1 |
| 1 | Pb12 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J24 |
| 1 | RIGHT | Buttons_Switches_THT:SW_PUSH_6mm_h5mm | SW5 |
| 1 | RST | Buttons_Switches_THT:SW_PUSH_6mm_h4.3mm | SW8 |
| 1 | STM32F407VGT6 | Housings_QFP:LQFP-100_14x14mm_Pitch0.5mm | U5 |
| 1 | SYS_LED | LEDs:LED_D3.0mm_FlatTop | D4 |
| 1 | TLV431 | TO_SOT_Packages_SMD:TSOT-23 | U4 |
| 1 | TP_3.3V | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | V3.3 |
| 1 | TP_AUDIO_L | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J9 |
| 1 | TP_AUDIO_R | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | J8 |
| 1 | TP_BATT | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | VBATT |
| 1 | TP_USB | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | VUSB |
| 1 | UP | Buttons_Switches_THT:SW_PUSH_6mm_h5mm | SW7 |
| 1 | USB_OTG | timekiller-footprints:USB_Micro-B-CircularHoles | J2 |
| 1 | VCAP | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | VCAP |
| 1 | VREF | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | VREF |
| 1 | uSD | timekiller-footprints:ATTEND-SD-TME | J6 |
More from stanislavbrtna/SDA_Wonder_HW
1- 2 layers35 × 18.8 mm

Similar boards
- 2 layers46 × 90 mm

- 2 layers109 × 64 mm

- 2 layers110 × 23 mm

- 2 layers66 × 99.1 mm

- 2 layers92.5 × 82.8 mm

Rifle and sensors
DAlexis/caustic-lasertag-system
Caustic project is a full-featured indoor and outdoor lasertag system
268 parts16 - 2 layers49 × 25.4 mm

- 6 layers60.6 × 100 mm

Gecko5education
logisim-evolution/GECKO5Education
Openhardware educational platform based on the ideas of the ulx3s and Gecko4Education
311 parts18MIT - 4 layers88.8 × 70.1 mm

Cyusb3014-breakout
danielkucera/cyusb3014-breakout
This design is a copy of QM Tech board: https://github.com/ChinaQMTECH/QMCYUSB3014USB3.0
70 parts11
Questions
How big is the TimekillerXtreme PCB?
It measures 61.5 × 105.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the TimekillerXtreme use?
114 parts, built around the STM32F407VGT6, FT230XS-R, NCP1529ASN and USBLC6-4. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the TimekillerXtreme KiCad files?
From the stanislavbrtna/SDA_Wonder_HW repository on GitHub, at the commit this page was made from: the board is Board/timekillerXtreme/timekillerXtreme.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the TimekillerXtreme design in my own project?
Its repository states no licence, so its author keeps all rights: ask stanislavbrtna before reusing the design.