
Antenna switch comms
sq9nje/matrix_antenna_switch
A 2x6 matrix antenna switch for HF HAM radio

A 2x6 matrix antenna switch for HF HAM radio
Relay module is an open-source printed circuit board by sq9nje, from the sq9nje/matrix_antenna_switch repository on GitHub, published under the Unlicense licence. It is a 2-layer board of 213.3 × 96 mm with 154 parts on 81 nets, routed with 762 tracks and 2,209 vias.
It is built around the 1N4148WS, TESDU24V and BC817, with the SL1002A600SM, 0ZCJ0025AF2E and ER1B among its other parts. Its parts include 45 diodes, 37 resistors, 18 switches, 14 capacitors and 12 transistors. It belongs with the radio and wireless and home automation and IoT boards of this library.
This directory contains all hardware design files for the 6x2 Matrix Antenna Switch Interface Module, designed in KiCad.
The interface module is the control hub for the 6x2 matrix antenna switch system, designed by SQ9NJE (Quirky Solutions). The main component of the interface module is an ESP32 DevKit v1 development board. The module is also equipped with a half-duplex RS485 interface with automatic transmission direction detection and a 5V voltage regulator.
Next to the control signal connector for connecting the relay module, there is an additional SAO (Simple Add-On) connector. This connector provides access to I2C bus signals, two GPIO pins, and 3.3V power supply with ground. In the future, it may be used to extend the hardware capabilities of the switch, such as adding a display, band decoder, etc.
🔧 Interactive BOM{:target="_blank"}
| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | 1N4148WS | Diode_SMD:D_SOD-323 | D3, D4, D13, D14, D17, D18, D19, D20, D28, D29, D33, D34, D35, D36, D43, D44 +2 |
| 18 | Fujitsu_FTR-K1C | QS_RF:Relay_DPDT_Fujitsu_FTR-K1C | K1, K2, K3, K4, K5, K6, K7, K10, K11, K12, K13, K14, K15, K16, K17, K18 +2 |
| 13 | 4.7k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R7, R8, R11, R12, R19, R20, R21, R24, R25, R32, R33, R36, R37 |
| 13 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D7, D8, D11, D12, D21, D22, D23, D26, D27, D37, D38, D41, D42 |
| 13 | TESDU24V | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D2, D9, D10, D15, D16, D24, D25, D30, D31, D32, D39, D40 |
| 12 | 100 | Resistor_SMD:R_2512_6332Metric_Pad1.52x3.35mm_HandSolder | R3, R4, R5, R6, R15, R16, R17, R18, R28, R29, R30, R31 |
| 12 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R2, R9, R10, R13, R14, R22, R23, R26, R27, R34, R35 |
| 12 | 1n | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C2, C3, C4, C5, C6, C9, C10, C11, C12, C13, C14 |
| 12 | BC817 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8, Q9, Q10, Q11, Q12 |
| 8 | Conn_Coaxial | QS_RF:UC1-Square-2HolesRight | A1, A2, A3, A4, A5, A6, TRX1, TRX2 |
| 8 | SL1002A600SM | QS_RF:GDT_SL1002A_HandSolder | E1, E2, E3, E4, E5, E6, E7, E8 |
| 2 | L_Small | Resistor_THT:R_Axial_DIN0411_L9.9mm_D3.6mm_P12.70mm_Horizontal | L1, L2 |
| 1 | 0ZCJ0025AF2E | Fuse:Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 1 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C7 |
| 1 | 470u | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C8 |
| 1 | Conn_01x02 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J2 |
| 1 | Conn_02x07_Odd_Even | Connector_IDC:IDC-Header_2x07_P2.54mm_Vertical | J1 |
| 1 | ER1B | Diode_SMD:D_SMA_Handsoldering | D45 |
The 147 most common of 154 parts.

sq9nje/matrix_antenna_switch
A 2x6 matrix antenna switch for HF HAM radio

sq9nje/matrix_antenna_switch
A 2x6 matrix antenna switch for HF HAM radio


ByTechLab/RF---Mostly-3D-Printed-Discone-Antenna--0.08-1-GHz-
Mostly 3D printed discone antenna for Software Definied Radio.

ondras12345/multicdc
RP2040-based 6-channel USB to UART converter with Zephyr RTOS

ondras12345/vetrnik
Electronics for heating water with power from a 2 kW wind turbine

MR-DOS/TDR_diploma_thesis
Time domain reflectometer. Includes Hardware, firmware and GUI in Octave. Also a diploma thesis.



It measures 213.3 × 96 mm and has 2 copper layers, 1.6 mm thick.
154 parts, built around the 1N4148WS, TESDU24V, BC817 and SL1002A600SM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the sq9nje/matrix_antenna_switch repository on GitHub, at the commit this page was made from: the board is relay_module/hardware/relay_module.kicad_pcb and its schematic archive/rs485_interface_module/hardware/antenna_switch_comms.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).