
Asac fc rev a
victorhook/asac-fc
asac fc is an rp2040 based flight controller made for FPV drone flying

Pxl is an open-source printed circuit board by souptik-samanta, from the souptik-samanta/fluid-dynamics repository on GitHub. It is a 4-layer board of 50.1 × 32 mm with 102 parts on 102 nets, routed with 781 tracks and 276 vias.
It is built around the RP2040, W25Q128JVSIQ and AMS1117-3.3, with the MPU-6050 and SRV05-4 among its other parts. Its parts include 26 capacitors, 11 resistors, 6 ICs, 3 connectors and 2 diodes. It belongs with the RP2040 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 50 | LED | LED_SMD:LED_0603_1608Metric | D_L_1_1, D_L_1_2, D_L_1_3, D_L_1_4, D_L_1_5, D_L_1_6, D_L_1_7, D_L_1_8, D_L_2_1, D_L_2_2, D_L_2_3, D_L_2_4, D_L_2_5, D_L_2_6, D3, D4 +34 |
| 9 | 100nF | Capacitor_SMD:C_0402_1005Metric | C9, C10, C13, C14, C15, C16, C17, C18, C19 |
| 4 | 220 | Resistor_SMD:R_0402_1005Metric | R1, R2, R14, R15 |
| 3 | 1uF | Capacitor_SMD:C_0402_1005Metric | C11, C12, C20 |
| 3 | 22uF | Capacitor_SMD:C_0603_1608Metric | C5, C7, C8 |
| 2 | .1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C23, C26 |
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric | C4, C6 |
| 2 | 15pF | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R3, R10 |
| 2 | 27.4 | Resistor_SMD:R_0402_1005Metric | R16, R17 |
| 2 | 5.1K | Capacitor_SMD:C_0402_1005Metric | R12, R13 |
| 2 | LED | LED_SMD:LED_0402_1005Metric | D1, D2 |
| 1 | 100n | Capacitor_SMD:C_0402_1005Metric | C3 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C25 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C30 |
| 1 | 120ohm.100Mhz | Inductor_SMD:L_0805_2012Metric | FB1 |
| 1 | 1uF | Capacitor_SMD:C_0805_2012Metric | C31 |
| 1 | 2.2nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C24 |
| 1 | 20K | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R20 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | BOOT_SEL | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW2 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_1.00mm:PinHeader_1x03_P1.00mm_Vertical_SMD_Pin1Left | J4 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_1.00mm:PinHeader_1x04_P1.00mm_Vertical | J5 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mm | Y1 |
| 1 | GP0 | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW1 |
| 1 | IS31FL3731-QF | Package_DFN_QFN:QFN-28-1EP_4x4mm_P0.4mm_EP2.4x2.4mm_ThermalVias | U6 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U5 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U4 |
| 1 | SRV05-4 | Package_TO_SOT_SMD:SOT-23-6 | U1 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J2 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U2 |

victorhook/asac-fc
asac fc is an rp2040 based flight controller made for FPV drone flying

souptik-samanta/Hackducky
Our board is powered by the reliable Raspberry Pi RP2040 microcontroller and includes 16 MB of flash storage, giving plenty of room for scripts and firmware.


khill25/Dreamdrive
Open source Retro Rom Carts and ODEs by Dreamcraft Industries


ArduProject/PCB_DRONE_C8
En este repositorio encontrareis los archivos de fabricación y las listas de montaje del PCB con STM32F103C8 que hemos visto en el curso.

ArduProject/PCB_DRONE_R8
En este repositorio encontrareis los archivos de fabricación y las listas de montaje del PCB con STM32F103R8 que hemos visto en el curso.

JH2k00/BioSensorBox
This repository contains the hardware and software for my project in the Advanced Topics in PCB Design lecture at the Technical University of Darmstadt
It measures 50.1 × 32 mm and has 4 copper layers, 1.6 mm thick.
102 parts, built around the RP2040, W25Q128JVSIQ, AMS1117-3.3 and MPU-6050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the souptik-samanta/fluid-dynamics repository on GitHub, at the commit this page was made from: the board is pxl.kicad_pcb and its schematic pxl.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask souptik-samanta before reusing the design.