Skip to the content
4 layers215.1 × 113.2 mmRear node board, the printed circuit board in 3D

Rear 존의 말단 두 노드를 한 장의 PCB로 합친 보드. H723 존 컨트롤러는 Nucleo-144 모듈 그대로 두고 J2 로 연결한다.

Size
215.1 × 113.2 mm
Copper layers
4
Thickness
1.62 mm
Parts
88
Nets
141
Pads
364
Tracks, vias
1,070, 172
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
23 Jul 2026
Updated
13 Sep 2026

Overview

Rear node board is an open-source printed circuit board by sngmn7, from the sngmn7/STM32_CAN_RTOS_ETHERNET repository on GitHub. It is a 4-layer board of 215.1 × 113.2 mm with 88 parts on 141 nets, routed with 1,070 tracks and 172 vias.

It is built around the STM32F446RET6, SN65HVD230D and AMS1117-3.3. Its parts include 32 capacitors, 23 resistors, 11 connectors, 7 ICs and 5 diodes. It belongs with the STM32 boards of this library.

Main components

3

README

rear_node_board/README.md

REAR NODE BOARD — STM32F446RET6 ×2

Rear 존의 말단 두 노드를 한 장의 PCB로 합친 보드. H723 존 컨트롤러는 Nucleo-144 모듈 그대로 두고 J2 로 연결한다.

text
[H723 Nucleo-144]  ── J2 (CAN 로직신호 4 + GND) ──┐
                                                   │
   ┌───────────────── REAR NODE BOARD ─────────────┴──────────────┐
   │  U3 ─ CAN500 ─ U4 ─ U1 (F446RET6, rear body)                 │
   │  U5 ─ CAN250 ─ U6 ─ U2 (F446RET6, 센서/램프 노드)             │
   │                        └ LED×4, 스위치, HC-SR04, BNO085      │
   └──────────────────────────────────────────────────────────────┘
              │
        J5 ── REAR-CAN-H 500k → 모터 노드(외부)

검증 상태: ERC 0 errors / 0 warnings, 배치검사 통과, 두 MCU 각각 64/64 핀 전부 연결(미연결은 트랜시버 Vref ×4, 의도된 NC).

배선 방식

436개 배선 + 51개 정션으로 실제 선이 그려져 있다. 라벨만 띄워놓은 게 아니다.

실선으로 그린 것방식
CAN 500k / 250k 버스세로 트렁크 + 각 노드로 가지 + 정션
종단 5세트JP→60R→중점→60R→CANL 직렬 체인, 중점에서 4.7nF→GND
LED 4개저항→애노드 실선, 캐소드→GND
크리스탈 2개크리스탈↔로드캡 실선, 캡→GND
스위치 + 풀업같은 노드로 실선 결선
디커플링 15개위쪽 +3V3 레일 / 아래쪽 GND 레일 실선 + 정션

MCU 두 개만 네트 라벨을 쓴다. 핀 128개를 시트 전체로 배선하면 오히려 읽을 수 없어지기 때문이고, 이건 실무 회로도의 표준 방식이다. 전기적 연결은 동일하며 네트리스트로 검증했다.

★ 네트 라벨 = 실제 배선이다

PCB 는 회로도의 선 그림을 보지 않는다. 네트리스트만 읽는다. 그래서 라벨로 연결하든 선으로 연결하든 PCB 결과는 완전히 같다.

이것을 말이 아니라 실물로 확인했다 — 이 회로도에서 PCB 를 실제로 생성했다.

text
netlist : 83 components, 136 nets
placed  : 83 footprints        <- 누락 0
nets    : 136 on board, 404 pads assigned
DRC     : 0 violations, 266 unconnected items

266 unconnected items 가 바로 rats nest 다. pcbnew 가 "이 266 개를 연결해야 한다"고 인식했다는 뜻이고, 곧 MCU 핀을 포함한 모든 연결이 정상적으로 넘어갔다는 증거다.

예를 들어 U2(F446) 의 핀들은 PCB 에서 이렇게 이어진다.

text
pin 11  TOGGLE_SW  -> R18.2, SW1.1
pin 14  LED_LEFT   -> R14.1
pin 30  ND_VCAP1   -> C27.1
pin 44  ND_CAN_RX  -> U6.4
pin 61  I2C1_SCL   -> J8.3, R19.2
pin  2  ND_PC13    -> J14.1

64 핀 전부가 이런 식으로 연결돼 있다.


1. 왜 F446 두 개인가

원래 rear body 노드는 F407VG(LQFP100)였지만 F446RET6(LQFP64)로 통일했다.

통일 전통일 후
MCU 종류F407VG + F446REF446RE ×2
풋프린트LQFP100 + LQFP64LQFP64 ×2
지원회로VCAP 2개 + 1개, 서로 다름완전 동일
BOM 라인21

⚠️ 펌웨어 이식 필요: F407 rear body 펌웨어는 CAN1 이 PD0/PD1 이었다. F446 LQFP64 에는 그 핀이 없어 PA11/PA12 로 옮겨야 한다. 현재 rear body 는 500k ping/echo(0x101→0x181)만 하므로 이식 부담은 작다.


2. 보드 구성

참조부품역할
U1STM32F446RET6rear body 노드, 500k 버스
U2STM32F446RET6센서/램프 노드, 250k 버스
U3SN65HVD230H723 FDCAN1 ↔ 500k
U4SN65HVD230U1 ↔ 500k
U5SN65HVD230H723 FDCAN2 ↔ 250k
U6SN65HVD230U2 ↔ 250k
U7AMS1117-3.35V → 3.3V
Y1, Y28 MHzHSE
JP1~JP5종단 점퍼아래 §3

커넥터

참조용도핀
J1VIN 5 V스크류터미널 2
J2H723 Nucleo (FDCAN1 TX/RX, FDCAN2 TX/RX, GND×2)6
J3 / J4SWD (U1 / U2) — 3V3, SWCLK, GND, SWDIO, NRST, SWO6
J5REAR-CAN-H 500k → 모터 노드3
J6REAR-CAN-L 250k 예비3
J7HC-SR04 (5 V)4
J8BNO085 IMU6
J9UART 콘솔 (U2)3
J10~J13U1 브레이크아웃 (43핀 전부)12/12/12/11
J14~J16U2 브레이크아웃 (30핀 전부)12/12/9

3. ★ 종단 점퍼 — 이것만은 틀리면 안 됨

버스드롭점퍼기본
REAR-CAN-H 500k3개 (H723, U1, 모터노드)JP1 (H723)삽입
JP2 (U1, 버스 중간)개방
JP3 (모터노드 쪽)삽입
REAR-CAN-L 250k2개JP4, JP5둘 다 삽입

3개를 다 끼우면 40 Ω 이 되어 드라이버가 규정 차동전압을 못 만들고 통신이 깨진다. 종단은 스플릿(60 Ω + 60 Ω, 중점 4.7 nF → GND) 방식.


4. 조립 시 반드시 지킬 것

① C26 / C27 (VCAP, 각 MCU 30번핀) — 필수 내부 레귤레이터 안정화용. 없거나 멀면 칩이 아예 부팅하지 않는다. 디커플링처럼 "있으면 좋은" 부품이 아니다. 핀 바로 옆에 배치할 것.

② R2 / R3 (BOOT0 풀다운, 각 60번핀) — 필수 빠지면 플래시 부팅이 안 되고 무작위로 시스템 부트로더로 들어간다. 커스텀 보드 첫 제작에서 가장 흔한 실패 원인.

③ SWD 헤더에 NRST 포함 클럭 설정을 잘못 넣었을 때 connect-under-reset 으로만 살릴 수 있다. NRST 가 없으면 그대로 벽돌이 된다.

④ VDD 핀마다 100 nF MCU 하나당 VDD 4개(19, 32, 48, 64) → 각각 바로 옆에.

⑤ J2 의 GND 를 반드시 연결 H723 Nucleo 는 자기 전원을 쓰지만, 트랜시버가 기준 전위를 공유해야 CAN 이 성립한다. GND 미공통이 CAN 무응답의 가장 흔한 원인이다.


5. 펌웨어 쪽 확인 사항

클럭을 HSE 로 바꿔야 한다. 현재 F446 펌웨어 SystemClock_Config() 는 HSI 를 쓴다 (RCC_OSCILLATORTYPE_HSI, PLLM=16, PLLN=336, PLLP=4 → 84 MHz).

STM32F4 의 HSI 는 25 °C 에서 ±1 %, 온도 범위 전체로는 더 나빠진다. CAN 은 통상 ±0.5 % 이하를 요구하므로 HSI 로는 마진이 없다. Nucleo 로 책상에서 짧은 배선일 때는 돌아가지만, 실제 배선이 길어지면 마진이 사라진다. Y1/Y2 를 달았으니 HSE 로 전환할 것.


6. PCB 뜰 때

  • 2층으로 충분하다. 최고 속도가 CAN 500 kbps 라 임피던스 제어·길이 매칭 불필요
  • 바텀은 통 GND 플레인
  • CANH/CANL 은 반드시 쌍으로 나란히, 트랜시버→커넥터 스터브 최소화
  • LQFP64 는 0.5 mm 피치 — 이것만 주의
  • HC-SR04 는 5 V 라 J7 전원만 5 V 레일에서 따온다

7. 아직 확인 못 한 것

항목왜
BNO085 모듈 내부 I2C 풀업있으면 R19/R20 을 빼야 한다 (중복 시 값 반토막)
모터 노드 자체 종단 유무있으면 JP3 를 개방해야 한다
VCAP 정확한 용량2.2 µF 는 ST 표준 권장값. 발주 전 데이터시트 재확인

8. 재생성

bash
# 회로도 + ERC + 네트리스트 + BOM + PDF
python tools/build.py

# 네트리스트 -> PCB (풋프린트 전부 로드 + 네트 할당 + 개략 배치)
"E:\Program files\bin\python.exe" tools\make_pcb.py rear_node_board

회로 수정은 tools/gen_rear_board.py 에서. KiCad GUI 에서 직접 고치면 다음 빌드에 덮어써진다.

make_pcb.py 는 레이아웃 시작점을 만들어 줄 뿐이다. 부품은 격자에 대충 뿌려져 있으니 pcbnew 에서 배치를 정리하고 라우팅하면 된다. 이미 만든 배치를 유지하려면 다시 돌리지 말고, 회로도를 고친 뒤 pcbnew 의 "회로도에서 PCB 업데이트" 를 쓰는 편이 낫다.

Parts

88
QtyValueFootprintReferences
19100nCapacitor_SMD:C_1206_3216MetricC2, C3, C5, C10, C11, C12, C15, C16, C17, C18, C19, C28, C29, C30, C31, C32 +3
6330Resistor_SMD:R_0805_2012MetricR19, R20, R21, R22, R23, R24
510kResistor_SMD:R_0805_2012MetricR2, R3, R7, R8, R9
5330RResistor_SMD:R_0805_2012MetricR10, R11, R12, R13, R14
410pCapacitor_SMD:C_1206_3216MetricC23, C24, C26, C27
4SN65HVD230DLibrary:SOIC127P599X175-8NU10, U11, U12, U13
310nCapacitor_SMD:C_0603_1608MetricC13, C20, C25
3120RResistor_SMD:R_0805_2012MetricR4, R5, R6
210uCapacitor_SMD:CP_Elec_4x5.4C1, C4
21kResistor_SMD:R_0805_2012MetricR28, R29
21uCapacitor_SMD:CP_Elec_4x5.4C14, C21
24u7Capacitor_SMD:CP_Elec_4x5.3C9, C22
2Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalACCEL1, ADC_BRAKE1
2FerriteBeadResistor_SMD:R_0805_2012MetricFB1, FB2
2STM32F446RET6Package_QFP:LQFP-64_10x10mm_P0.5mmU4, U7
11KResistor_SMD:R_0805_2012MetricR1
12KResistor_SMD:R_0805_2012MetricR15
1AMS1117-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2U1
1CAN-H 500k -> MOTORConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ5
1Conn_01x03Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ10
1Conn_01x03_PinConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalDHT1
1Conn_01x06Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Verticalfront2
1ECS-80-10-30B-CWN-TR-1Library:XTAL_ECS-80-10-30B-CWN-TRY4
1ECS-80-10-30B-CWN-TR-2Library:XTAL_ECS-80-10-30B-CWN-TRY3
1GF063P1Library:GF063P1VR1
1H723 NUCLEO-144Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ2
1LED_BLED_THT:LED_D5.0mmD4
1LED_LLED_THT:LED_D5.0mmD2
1LED_RLED_THT:LED_D5.0mmD3
1LED_SLED_THT:LED_D5.0mmD5
1PWRLED_THT:LED_D5.0mmD1
1SWButton_Switch_THT:SW_PUSH_6mmSW1
1SWD - U1 REAR BODYConnector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ3
1SWD - U2 NODEConnector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ4
1UART CONSOLE (U1)Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ8
1UART CONSOLE (U2)Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ9
1VIN 5VTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_HorizontalJ1
1bno085_1Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ7
1bno085_2Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ6
1hc04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ11

Similar boards

  • 4 layers140 × 70 mmRcm, the printed circuit board in 3D

    Rcm

    Twistiee/rcm

    A CAN-controlled relay driver for a car. 21 universal channels, each of which is simultaneously a low-side output and an input — so the same board builds as a relay controller or as a switch panel, decided in firmware…

    159 parts
  • 4 layers224.7 × 185.5 mmLine follow stm, the printed circuit board in 3D

    Line follow stm

    Lonelybarbarian0/stm32-line-follower

    An advanced line follower based on STM32f446RE. This design consists of 12 Analog IR sensors (CNY70) , a dual H-bridge driver (TB6612FNG) , has I2C ports for oled display , push buttons , 12V battery accomodation , SWD…

    96 parts
  • 2 layers96 × 74.4 mmMonolith, the printed circuit board in 3D

    Monolith

    luftaquila/monolith

    DIY wireless real-time datalogging platform for Student Formula and Baja.

    138 parts45
  • 4 layers180 × 120 mmMG ZS V2, the printed circuit board in 3D

    MG ZS V2

    damienmaguire/MG-EV-Inverter

    Reverse engineering of the drive motor and inverter used in MG Electric Vehicles

    177 parts17GPL-3.0
  • 4 layers110 × 80 mmPNP MOBO V2, the printed circuit board in 3D

    PNP MOBO V2

    GabrielD98/PickUS_and_PlacUS

    pick and place de PCB pour projet S4 de robotique

    126 parts5MIT
  • 4 layers84.5 × 60 mmBldc driver, the printed circuit board in 3D

    Bldc driver

    koson/spel-bldc-esc

    Open-source BLDC motor electronic speed controller (yet another)

    100 parts4
  • 2 layers96.6 × 63.9 mmPDU, the printed circuit board in 3D

    PDU

    OpenSkyHawk/OpenSkyhawk

    DCS A-4E Skyhawk home cockpit — 3D-printed panels, custom PCBs, STM32/RP2040 firmware

    72 parts3
  • 4 layers32 × 25.5 mmEngineControl, the printed circuit board in 3D

    EngineControl

    Badger-Embedded/BadgerHW-EngineControl

    62 parts2

Questions

How big is the Rear node board PCB?

It measures 215.1 × 113.2 mm and has 4 copper layers, 1.62 mm thick.

What parts does the Rear node board use?

88 parts, built around the STM32F446RET6, SN65HVD230D and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Rear node board KiCad files?

From the sngmn7/STM32_CAN_RTOS_ETHERNET repository on GitHub, at the commit this page was made from: the board is rear_node_board/rear_node_board.kicad_pcb and its schematic rear_node_board/rear_node_board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Rear node board design in my own project?

Its repository states no licence, so its author keeps all rights: ask sngmn7 before reusing the design.